2003 NISSAN TEANA load capacity

CYLINDER BLOCK
EM-83
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM


A widely use engine stand can be used.
CAUTION:
Use engine stand that has a load capacity [approximately
150 kg (331 lb) or more] large enough for supporting the
engine weight.
NOTE:
This example is an engine stand for holding at transaxle
mounting side with drive plate removed.
3. Drain engine oil. Refer to LU-9, "
Changing Engine Oil" .
4. Drain engine coolant by removing water drain plug from inside of
engine.
5. Remove cylinder head. Refer to EM-65, "
CYLINDER HEAD" .
6. Remove knock sensor.
CAUTION:
Carefully handle knock sensor avoiding shocks.
7. Remove crankshaft position sensor (POS).
CAUTION:

Avoid impacts such as a dropping.

Do not disassemble.

Keep it away from metal particles.

Do not place sensor in a location where it is exposed to
magnetism.
8. Remove drive plate.

Secure drive plate with stopper plate, and remove mounting
bolts.
NOTE:
Use TORX socket (size E20).
CAUTION:
Be careful not to damage or scratch drive plate.
PBIC0085E
PBIC2443E
PBIC2191E
PBIC2352E

EM-230
[VQ]
CYLINDER BLOCK


A widely use engine stand can be used.
CAUTION:
Use engine stand that has a load capacity [approximately
220 kg (441 lb) or more] large enough for supporting the
engine weight.
NOTE:
This example is engine stand for holding at transaxle mount-
ing side with drive plate removed.
5. Drain engine oil. Refer to LU-21, "
Changing Engine Oil" .
6. Drain engine coolant by removing water drain plugs from cylin-
der block both sides at “A” and “D” and cylinder block front side
at “B” as shown in the figure.
NOTE:
Water drain plug at the right bank side for VQ35DE is also used
as a connector of water pipe for oil cooler. Refer to LU-23, "
OIL
COOLER (VQ35DE)" .
7. Remove drive plate. Fix crankshaft pulley with pulley holder [SST: KV10109300], and remove mounting
bolts.

Loosen mounting bolts in diagonal order.
CAUTION:

Do not disassemble drive plate.

Do not place drive plate with signal plate facing down.

When handling signal plate, take care not to damage or
scratch it.

Handle signal plate in a manner that prevents it from
becoming magnetized.
8. Remove cylinder head. Refer to EM-210, "
CYLINDER HEAD" .
9. Remove knock sensor.
CAUTION:
Carefully handle sensor avoiding shocks.
PBIC0085E
PBIC2487E
SEM760G

SC-38
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
BatteryBKS001MO
StarterBKS0027G
AlternatorBKS0027H
Applied modelStandard
Ty p e80D23L
Capacity12V -52AH
Applied model VQ23DE VQ35DE QR20DE
Ty p eM0T87181 M1T68681 S114 - 844
MITSUBISHI make HITACHI make
Reduction gear type
System voltage12 V
No-loadTerminal voltage 11 V
Current Less than 90 A
Revolution More than 2,800 rpm More than 2,750 rpm More than 2,700 rpm
Minimum diameter of commutator 28.8 mm (1.134 in) 28.0 mm (1.102 in)
Minimum length of brush 7.0 mm (0.276 in) 10.5 mm (0.413 in)
Brush spring tension18.3 - 24.8 N
(1.87 - 2.53 kg, 4.12 -
5.58 lb)15.0 - 20.4 N
(1.53 - 2.08 kg, 3.3 -
1.5 lb)16.2 N
(1.65 kg, 3.64 lb)
Clearance between bearing metal and armature shaft Less than 0.2 mm (0.008 in)
Clearance “L” between pinion front edge and pinion stopper0.5 - 2.0 mm (0.020 -
0.079 in)––
Movement “L” in height of pinion assembly –0.5 - 2.0 mm (0.020 -
0.079 in)0.3 - 2.5 mm (0.012 -
0.098 in)
Applied model VQ23DE, VQ35DE QR20DE
TypeLR1110 - 723E LR1110 - 713B
HITACHI make
Nominal rating12 V - 110 A
Ground polarityNegative
Minimum revolution under no-load (When 13.5 V is applied) Less than 1,100 rpm
Hot output current (When 13.5 V is applied)(More than 35 A/1,300 rpm)
More than 70 A/1,800 rpm
More than 91 A/2,500 rpm
More than 110 A/5,000 rpm
Regulated output voltage 14.1 - 14.7 V
Minimum length of brush More than 6.00 mm (0.236 in)
Brush spring pressure 1.00 - 3.43 N (102 - 350 g, 3.60 - 12.34 oz)
Slip ring minimum outer diameter More than 26.0 mm (1.024 in)
Rotor (Field coil) resistance 2.16 - 2.46 Ω