2003 NISSAN TEANA reverse

DOOR MIRROR
GW-77
C
D
E
F
G
H
J
K
L
MA
B
GW

Removal and InstallationBIS0010I
CAUTION:
Be careful not to damage the mirror body.
REMOVAL
1. Remove the front door finisher. Refer to EI-35, "DOOR FINISHER" .
2. Remove the tweeter harness connector from the corner cover (tweeter equipped model).
3. Remove the door mirror harness connector.
4. Remove the corner cover.
5. Remove the door mirror mounting nuts, and remove the door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
PIIA6330E
1. Door mirror assembly 2. Nut 3. Corner cover

GW-80
INSIDE MIRROR

INSIDE MIRRORPFP:96321
Removal and InstallationBIS0010K
REMOVAL
Slide the mirror upward to remove.
INSTALLATION
Install in the reverse order of removal.
1. Inside mirror
PIIA6795E

IP-18
INSTRUMENT PANEL ASSEMBLY

6. Disconnect sunload sensor, auto light sensor, and security indicator harness connectors. Refer to AT C -
111 , "SUNLOAD SENSOR" and LT- 7 4 , "Removal and Installation for Optical Sensor" .
7. Remove instrument panel & pad from passenger side door opening.
8. Remove screws, and then remove instrument panel pad from instrument panel.
(Z) Instrument Center Lower Panel
1. Remove screws from back of instrument panel & pad.
2. Remove instrument center lower panel forward from front side.
INSTALLATION
Install in the reverse order of removal.

IP-20
INSTRUMENT PANEL ASSEMBLY

8. Remove screws, and then remove console box.
9. Remove screws from both sides of bottom of rear end, and then remove console bracket.
Assembly
Assemble in the reverse order of disassembly.
INSTRUMENT PASSENGER LOWER PANEL
Disassembly
1. Remove caught point of tip of damper from back of glove box lid
side using a screwdriver wrapped with tape.
2. Remove screws from center of back surface, and then remove damper body.
3. Remove glove box pin from center of back surface using a
screwdriver wrapped with tape, and then remove glove box from
instrument passenger lower panel.
4. Remove illumination from back surface upper using a screwdriver wrapped with tape.
1. Pocket 2. Instrument passenger lower panel 3. Glove box pin
4. Glove box 5. Damper 6. Screw
7. Glove box illumination
PIIB1793E
PIIB1794E
PIIA6352E

INSTRUMENT PANEL ASSEMBLY
IP-21
C
D
E
F
G
H
J
K
L
MA
B
IP

5. Remove screws, and then remove pocket.
Assembly
Assemble in the reverse order of disassembly.
CLUSTER LID D
Disassembly
1. Remove screws, and then remove instrument upper box.
2. Disconnect pawls, and then remove center ventilator grille. Refer to ATC-126, "
Removal of Center Ventila-
tor Grilles" .
Assembly
Assemble in the reverse order of disassembly.
PIIB0640E
1. Screw 2. Instrument upper box 3. Center ventilator grille
4. Cluster lid D
PIIB0603E

LAN-8
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSIS

Symptom When Error Occurs in CAN Communication SystemBKS0040U
In CAN communication system, multiple units mutually transmit and receive signals. Each unit cannot transmit
and receive signals if any error occurs on CAN communication line. Under this condition, multiple control units
related to the root cause malfunction or go into fail-safe mode.
ERROR EXAMPLE
NOTE:

Each vehicle differs in symptom of each unit under fail-safe mode and CAN communication line wiring.

Refer to LAN-41, "Abbreviation List" for the unit abbreviation.
Example: TCM branch line open circuit
SKIB8738E
Unit name Symptom
ECM Engine torque limiting is affected, and shift harshness increases.
BCM Reverse warning chime does not sound.
EPS control unit Normal operation.
Combination meter

Shift position indicator and OD OFF indicator turn OFF.

Warning lamps turn ON.
ABS actuator and electric unit (control unit) Normal operation.
TCM No impact on operation.
IPDM E/R Normal operation.

LAN-10
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSIS

Example: Main Line Between Data Link Connector and ABS Actuator and Electric Unit (Con-
trol Unit) Open Circuit
SKIB8740E
Unit name Symptom
ECM Engine torque limiting is affected, and shift harshness increases.
BCM

Reverse warning chime does not sound.

The front wiper moves under continuous operation mode even though the front
wiper switch being in the intermittent position.
EPS control unit The steering effort increases.
Combination meter

The shift position indicator and OD OFF indicator turn OFF.

The speedometer is inoperative.

The odo/trip meter stops.
ABS actuator and electric unit (control unit) Normal operation.
TCM No impact on operation.
IPDM E/RWhen the ignition switch is ON,

The headlamps (Lo) turn ON.

The cooling fan continues to rotate.

TROUBLE DIAGNOSIS
LAN-11
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
MA
B
LAN

Example: CAN-H, CAN-L Harness Short Circuit
SKIB8741E
Unit name Symptom
ECM

Engine torque limiting is affected, and shift harshness increases.

Engine speed drops.
BCM

Reverse warning chime does not sound.

The front wiper moves under continuous operation mode even though the front
wiper switch being in the intermittent position.

The room lamp does not turn ON.

The engine does not start (if an error or malfunction occurs while turning the igni-
tion switch is OFF.)

The steering lock does not release (if an error or malfunction occurs while turning
the ignition switch is OFF.)
EPS control unit The steering effort increases.
Combination meter

The tachometer and the speedometer do not move.

Warning lamps turn ON.

Indicator lamps do not turn ON.
ABS actuator and electric unit (control unit) Normal operation.
TCM No impact on operation.
IPDM E/RWhen the ignition switch is ON,

The headlamps (Lo) turn ON.

The cooling fan continues to rotate.