2003 NISSAN TEANA reverse

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-175
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001PZ
SIDE TURN SIGNAL LAMP
1. Remove side turn signal lamp. Refer to LT- 1 7 5 , "Removal and Installation" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
FRONT TURN SIGNAL LAMP
Refer to LT- 3 5 , "Bulb Replacement" .
REAR TURN SIGNAL LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS001Q2
SIDE TURN SIGNAL LAMP
Removal
1. While pressing side turn signal lamp to direction A (vehicle
front), pull it to direction B and then remove it.
2. Disconnect side turn signal lamp connector.
NOTE:
Support side turn signal lamp harness with tape so that it won't
fall into the front fender.
CAUTION:
Install the side turn signal lamp housing with the bead fac-
ing up.
Installation
Installation is the reverse order of removal.
FRONT TURN SIGNAL LAMP
Refer to LT- 3 6 , "Removal and Installation" .
REAR TURN SIGNAL LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . Side turn signal lamp : 12V - 5W
PKIA0015E
SKIA7249E

LT-176
LIGHTING AND TURN SIGNAL SWITCH

LIGHTING AND TURN SIGNAL SWITCHPFP:25540
Removal and InstallationBKS001Q4
REMOVAL
1. Remove steering column cover. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" .
2. While pressing pawls in direction as shown in the figure, pull
lighting and turn signal switch toward driver door and disconnect
from the base.
INSTALLATION
Installation is the reverse order of removal.
Switch Circuit InspectionBKS001Q5
Refer to LT- 1 8 5 , "Combination Switch Inspection" .
SKIB0899E

HAZARD SWITCH
LT-177
C
D
E
F
G
H
I
J
L
MA
B
LT

HAZARD SWITCHPFP:25290
Removal and InstallationBKS001Q6
REMOVAL
1. Remove cluster lid D. Refer to IP-10, "INSTRUMENT PANEL
ASSEMBLY" .
2. Disconnect connector.
3. Remove screw and remove hazard switch integral with center
ventilator grille from cluster lid D.
4. Pawl on rearward and remove hazard switch.
INSTALLATION
Installation is the reverse order of removal.
PKIB7984E

LT-192
STOP LAMP

Bulb ReplacementBKS001QD
HIGH-MOUNTED STOP LAMP
Replacement integral with high-mounted stop lamp. Refer to LT- 1 9 2 , "Removal and Installation" .
STOP LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS0040N
HIGH-MOUNTED STOP LAMP
Removal
1. Remove rear parcel shelf finisher. Refer to EI-43, "Removal and Installation" .
2. Disconnect high-mounted stop lamp connector.
3. Remove high-mounted stop lamp mounting screws and remove
high-mounted stop lamp from rear parcel shelf finisher.
Installation
Note the following, and installation is the reverse order of removal.
STOP LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . High-mounted stop lamp : LED
SKIA6346E
High-mounted stop lamp
mounting screws: 3.15 N·m (0.32 kg-m, 28in-lb)

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-215
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001QX
LICENSE PLATE LAMP
1. Remove trunk lid finisher inner. Refer to EI-59, "REMOVAL AND
INSTALLATION FOR TRUNK LID FINISHER INNER" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb from its socket.
PARKING LAMP
Refer toLT- 3 5 , "Bulb Replacement" .
TAIL LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS0040M
LICENSE PLATE LAMP
Removal
1. Remove trunk lid finisher. Refer to EI-33, "Removal and Installa-
tion" .
2. While pressing the license plate lamp to left side, pull right side
of it and remove.
3. Disconnect license plate lamp connector.
Installation
Installation is the reverse order of removal.
PARKING LAMP
Refer to LT- 3 6 , "Removal and Installation" .
TAIL LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . License plate lamp : 12V - 5W
SKIA6350E
SKIA6349E

LT-216
REAR COMBINATION LAMP

REAR COMBINATION LAMPPFP:26554
Bulb ReplacementBKS001R0
REAR TURN SIGNAL LAMP BULB, BACK-UP LAMP BULB AND STOP/TAIL LAMP BULB
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Turn tail lamp bulb socket (1), rear turn signal lamp bulb socket
(2), back-up lamp bulb socket (3) (right side) and rear fog lamp
bulb socket (3) (left side) counterclockwise and unlock it.
3. Remove tail lamp bulb (4), rear turn signal lamp bulb (5), back-
up lamp bulb (6) (right side) and rear fog lamp bulb (6) (left
side).
Removal and InstallationBKS001R1
REMOVAL
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting nuts (A).
4. Pull the rear combination lamp (1) toward rear of the vehicle and
remove clip (B) and locating pin (C) from the vehicle.
5. Remove seal packing (2) from rear combination lamp (1).
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Seal packing cannot be reused.Tail lamp : 12V - 5W
Rear turn signal lamp : 12V - 21W
Back-up lamp (Right side) : 12V - 21W
Rear fog lamp (Left side) : 12V - 21W
Stop lamp : LED
SKIB8646J
PKIC9679J
Rear combination lamp mounting nut : 5.1 N·m (0.52 kg-m, 45 in-lb)

LT-242
INTERIOR ROOM LAMP

IGNITION KEYHOLE ILLUMINATION
1. Remove steering column cover. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" .
2. Remove screw, and remove NATS antenna amp.
3. Pull out ring and turn bulb socket to left to release lock.
Removal and InstallationBKS001RF
MAP LAMP
Removal
1. Insert a clip driver or suitable tool and disengage the pawl fit-
tings the map lamp.
2. Disconnect map lamp connector and remove map lamp.
Installation
Installation is the reverse order of removal.
STEP LAMP
Removal
1. Insert a clip driver or a suitable tool and remove lens and bulb
housing.
2. Disconnect step lamp connector.
Installation
Installation is the reverse order of removal.Ignition keyhole illumination : 14V - 1.4W
SKIA6362E
SKIA8659E
SKIB0900E

INTERIOR ROOM LAMP
LT-243
C
D
E
F
G
H
I
J
L
MA
B
LT

PERSONAL LAMP
Removal
1. Use a clip driver or similar tool to press metal clip, and remove
personal lamp.
2. Disconnect personal lamp connector.
Installation
Installation is the reverse order of removal.
TRUNK ROOM LAMP
Removal
1. Remove rear parcel shelf finisher assembly. Refer to EI-43, "REAR PARCEL SHELF FINISHER" .
2. Disconnect trunk room lamp connector.
3. Press pawl and remove trunk room lamp.
Installation
Installation is the reverse order of removal.
SKIA6360E
SKIA6366E