2003 NISSAN TEANA service

BRC-2 ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) ... 35
Removal and Installation ........................................ 35
COMPONENTS ................................................... 35
REMOVAL ........................................................... 36
INSTALLATION .................................................... 36
VDC/TCS/ABS
PRECAUTIONS ......................................................... 37
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................. 37
Precautions for Brake System ................................ 37
Precautions for Brake Control ................................ 37
PREPARATION ......................................................... 39
Special Service Tools ............................................. 39
ON-VEHICLE SERVICE ............................................ 40
Adjustment of Steering Angle Sensor Neutral Posi-
tion .......................................................................... 40
OPERATION PROCEDURE ................................ 40
SYSTEM DESCRIPTION .......................................... 41
System Diagram ..................................................... 41
Functions ................................................................ 41
VDC ..................................................................... 41
TCS ..................................................................... 41
ABS ..................................................................... 42
EBD ..................................................................... 42
Fail-Safe Function .................................................. 42
VDC/TCS SYSTEM ............................................. 42
ABS, EBD SYSTEM ............................................ 42
Hydraulic Circuit Diagram ....................................... 43
CAN Communication .............................................. 43
SYSTEM DESCRIPTION .................................... 43
TROUBLE DIAGNOSIS ............................................ 44
How to Perform Trouble Diagnosis Quick and Accu-
rate Repair .............................................................. 44
INTRODUCTION ................................................. 44
DIAGNOSIS FLOW CHART ................................ 45
ASKING COMPLAINTS ....................................... 46
EXAMPLE OF DIAGNOSIS SHEET .................... 46
Component Parts Location ..................................... 47
Schematic ............................................................... 48
Wiring Diagram — VDC — ..................................... 49
Control Unit Input/Output Signal Specifications ...... 55
REFERENCE VALUE FROM CONSULT-II ......... 55
CONSULT-II Functions ........................................... 57
CONSULT-II MAIN FUNCTION ........................... 57
CONSULT-II SETTING PROCEDURE ................ 57
Self-Diagnosis ........................................................ 58
DESCRIPTION .................................................... 58
OPERATION PROCEDURE ................................ 58
ERASE MEMORY ............................................... 58
DISPLAY ITEM LIST ........................................... 59
Data Monitor ........................................................... 61
OPERATION PROCEDURE ................................ 61
DISPLAY ITEM LIST ........................................... 61
Active Test .............................................................. 63
OPERATION PROCEDURE ................................ 63TEST ITEM .......................................................... 64
For Fast and Accurate Diagnosis ............................ 65
PRECAUTIONS FOR DIAGNOSIS ..................... 65
Basic Inspection ...................................................... 66
BRAKE FLUID LEVEL, LEAKAGE AND BRAKE
PAD ...................................................................... 66
POWER SUPPLY CIRCUIT TERMINAL LOOSE-
NESS AND BATTERY ......................................... 66
INSPECTION OF ABS WARNING LAMP, BRAKE
WARNING LAMP, VDC OFF INDICATOR LAMP,
AND SLIP INDICATOR LAMP ............................. 66
TROUBLE DIAGNOSIS FOR SYSTEM .................... 68
Wheel Sensor System ............................................ 68
Engine System ........................................................ 70
ABS Actuator and Electric Unit (Control Unit) 1 ...... 70
Steering Angle Sensor System ............................... 71
Yaw Rate/Side/Decel G Sensor System ................. 72
Pump Motor, Motor Relay System .......................... 74
Park/Neutral Position (PNP) Switch Circuit ............. 75
Solenoid and VDC Change-Over Valve, Actuator
Relay System .......................................................... 76
Stop Lamp Switch System ...................................... 77
ABS Actuator and Electric Unit (Control Unit) Power
Supply and Ground System .................................... 78
Brake Fluid Level Switch System ............................ 80
CAN Communication System ................................. 81
Component Parts Inspection ................................... 81
VDC OFF SWITCH .............................................. 81
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 82
Excessive ABS Function Operation Frequently ...... 82
Unexpected Pedal Reaction ................................... 83
Longer Stopping Distance ....................................... 83
ABS Function Does Not Operate ............................ 84
Pedal Vibration and ABS Operation Sound Occurs ... 84
Vehicle Jerks During VDC/TCS/ABS Control .......... 85
WHEEL SENSORS ................................................... 86
Removal and Installation ......................................... 86
COMPONENTS ................................................... 86
REMOVAL ............................................................ 86
INSTALLATION .................................................... 86
SENSOR ROTOR ...................................................... 87
Removal and Installation ......................................... 87
FRONT ................................................................. 87
REAR ................................................................... 87
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) ... 88
Removal and Installation ......................................... 88
COMPONENTS ................................................... 88
REMOVAL ............................................................ 89
INSTALLATION .................................................... 89
G SENSOR ................................................................ 90
Removal and Installation ......................................... 90
REMOVAL ............................................................ 90
INSTALLATION .................................................... 90
STEERING ANGLE SENSOR ................................... 91
Removal and Installation ......................................... 91
REMOVAL ............................................................ 91
INSTALLATION .................................................... 91

PRECAUTIONS
BRC-3
[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

[ABS]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BFS000CK
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemBFS000CL

Recommended fluid is brake fluid “DOT 3” or “DOT 4”. Refer to MA-14, "RECOMMENDED FLUIDS AND
LUBRICANTS" .

Never reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas.

To clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.

Never use mineral oils such as gasoline or kerosene. They will
ruin rubber parts of the hydraulic system.

Using a flare nut wrench when removing flare nuts, and use a
flare nut torque wrench when tighten brake tube flare nuts.

When installing brake tubes, be sure to check torque.

Before working, turn ignition switch OFF and disconnect electri-
cal connector of ABS actuator and electric unit (control unit) or
battery negative terminal.
WARNING:
Clean brake pads and shoes with a waste cloth, then wipe with
a dust collector.
Precautions for Brake ControlBFS000CM

During ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating noise may
be heard from engine room. This is a normal condition of operation check.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.

When an error is indicated by ABS or another warning lamp, collect all necessary information from cus-
tomer (what symptoms are present under what conditions) and check for simple causes before starting
diagnostic servicing. Besides electrical system inspection, check brake booster operation, brake fluid
level, and fluid leaks.

If tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.

If there is a radio, antenna, or antenna lead-in wire (including wiring) near control module, ABS function
may have a malfunction or error.

If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits, and improper wiring.
SBR820BA

BRC-4
[ABS]
PREPARATION

PREPARATIONPFP:00002
Special Service ToolsBFS000CN
Tool number
Tool nameDescription
GG94310000
Flare nut torque wrench
a:10 mm (0.39 in)Installing brake tube
NT406

BRC-30
[ABS]
TROUBLE DIAGNOSIS FOR SYMPTOMS

TROUBLE DIAGNOSIS FOR SYMPTOMSPFP:00007
Excessive ABS Function Operation FrequencyBFS000DC
1. CHECK START
Check front/rear brake force distribution using a brake tester. Refer to BR-40, "
SERVICE DATA AND SPECIFI-
CATIONS (SDS)" .
OK or NG
OK >> GO TO 2.
NG >> Check brake system.
2. CHECK FRONT AND REAR AXLE
Check to make sure that there is no excessive play in the front and rear axles. Refer to Front: FAX-5, "
On-
Vehicle Inspection" , Rear: RAX-3, "On-Vehicle Inspection" .
OK or NG
OK >> GO TO 3.
NG >> Repair.
3. CHECK WHEEL SENSOR AND SENSOR ROTOR
Check wheel sensor and sensor rotor for the following.

Sensor installation for damage

Sensor rotor installation for damage

Sensor connector connection

Sensor harness inspection
OK or NG
OK >> GO TO 4.
NG >>

Replace wheel sensor or sensor rotor.

Repair harness.
4. CHECK ABS WARNING LAMP DISPLAY
Make sure that the warning lamp turns off approximately 1 second after the ignition switch is turned ON or
when driving.
OK or NG
OK >> Normal
NG >> Perform self-diagnosis. Refer to BRC-17, "
Self-Diagnosis" .
Unexpected Pedal ActionBFS000DD
1. CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Refer to BR-6, "
Inspection and Adjustment" .
Is the stroke too big?
YES >>
Bleed air from the brake piping. Refer to BR-10, "Bleeding Brake System" .

Check brake pedal, brake booster, and master cylinder for mount play, looseness, brake fluid
leakage, etc. Repair if necessary. Refer to Brake pedal: BR-7, "
COMPONENTS" , brake
booster and master cylinder: BR-22, "
COMPONENTS" .
NO >> GO TO 2.

BRC-36
[ABS]
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)

REMOVAL
1. Disconnect ABS actuator and electric unit (control unit) connector.
2. Loosen brake tube flare nuts, then remove brake tubes from ABS actuator and electric unit (control unit).
3. Remove ABS actuator and electric unit (control unit) mounting bolts.
4. Remove ABS actuator and electric unit (control unit) from vehicle.
CAUTION:
Be careful of the following when removing ABS actuator and electric unit (control unit).

If the part number on the part number label (pasted on actuator upper surface) is the same, ABS
actuator and electric unit (control unit) cannot be used on another vehicle.
If it is used on another vehicle, ABS warning lamp, may turn ON or ABS may not operate normally.
When replacing ABS actuator and electric unit (control unit), must use new service parts.

Before servicing, disconnect both battery cables.

To remove brake tube, use a flare nut torque wrench to prevent flare nuts and brake tube from
being damaged. To install, use a flare nut torque wrench (commercial service tool) and tighten
with the specified torque.

Do not apply excessive impact to actuator, such as dropping it.

Do not remove and install ABS actuator and electric unit (control unit) by holding harness.
INSTALLATION
Install is in the reverse order of the removal.
CAUTION:
Be careful of the following when installing ABS actuator and electric unit (control unit).

Tighten the mounting bolts and nuts with the specified torque.

After the work, bleed air from brake piping. Refer to BR-10, "Bleeding Brake System" .

After installing body harness connector in the actuator, make sure connector is securely locked.

PRECAUTIONS
BRC-37
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

[VDC/TCS/ABS]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BFS000G3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemBFS000DL

Recommended fluid is brake fluid “DOT 3” or “DOT 4”. Refer to MA-14, "RECOMMENDED FLUIDS AND
LUBRICANTS" .

Never reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas.

To clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.

Never use mineral oils such as gasoline or kerosene. They will
ruin rubber parts of the hydraulic system.

Using a flare nut wrench when removing flare nuts, and use a
flare nut torque wrench when tighten brake tube flare nuts.

When installing brake tubes, be sure to check torque.

Before working, turn ignition switch OFF and disconnect electri-
cal connector of ABS actuator and electric unit (control unit) or
battery negative terminal.
WARNING:
Clean brake pads and shoes with a waste cloth, then wipe with
a dust collector.
Precautions for Brake ControlBFS000DM

During ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating noise may
be heard from engine room. This is a normal status of operation check.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.

When an error is indicated by ABS or another warning lamp, collect all necessary information from cus-
tomer (what symptoms are present under what conditions) and check for simple causes before starting
diagnostic servicing. Besides electrical system inspection, check brake booster operation, brake fluid
level, and fluid leaks.

If tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.

If there is a radio, antenna, or antenna lead-in wire (including wiring) near control module, ABS function
may have a malfunction or error.

If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits, and improper wiring.

If the following components are replaced with non-genuine components or converted, the VDC OFF indi-
cator lamp and SLIP indicator lamp may turn on or the VDC system may not operate properly. Compo-
nents related to suspension (Shock Absorber, Strut, Spring, Bush, etc.), Tires, wheels (exclude specified
SBR820BA

PREPARATION
BRC-39
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

PREPARATIONPFP:00002
Special Service ToolsBFS000DN
Tool number
Tool nameDescription
GG994310000
Flare nut torque wrench
a:10 mm (0.39 in) / 12 mm (0.47 in)Installing brake tube
NT406

BRC-40
[VDC/TCS/ABS]
ON-VEHICLE SERVICE

ON-VEHICLE SERVICEPFP:00000
Adjustment of Steering Angle Sensor Neutral PositionBFS000DO
In case of doing work that applies to the list below, make sure to adjust neutral position of steering angle sen-
sor before running vehicle.
×: Required
–: Not required
OPERATION PROCEDURE
1. Stop vehicle with front wheels in straight-ahead position.
2. Perform CONSULT-II Starting Procedure. Refer to GI-34, "
CONSULT-II Start Procedure" .
3. Touch the “CONSULT-II screen in the order of “ABS”, “WORK SUPPORT” and “ST ANGLE SENSOR
ADJUSTMENT”. Refer to BRC-57, "
CONSULT-II SETTING PROCEDURE" .
4. Touch “START”.
CAUTION:
Do not touch steering wheel while adjusting steering angle
sensor.
5. After approximately 10 seconds, touch “END”. (After approxi-
mately 60 seconds, it ends automatically.)
6. Turn ignition switch to OFF, then turn to the ON again.
CAUTION:
Be sure to perform above operation.
7. Run vehicle with front wheels in straight-ahead position, then
stop.
8. Select “DATA MONITOR”, “SELECTION FROM MENU”, and “STR ANGLE SIG” on CONSULT-II screen.
Then make sure “STR ANGLE SIG” is within 0 ± 3.5 °. If the value is more than the specification, repeat
steps 3 to 7.
9. Erase memory of ABS actuator and electric unit (control unit) and ECM.
10. Turn ignition switch OFF.
Situation Adjustment of Steering Angle Sensor Neutral Position
Removing/Installing ABS actuator and electric unit (control unit)−
Replacing ABS actuator and electric unit (control unit)×
Removing/Installing steering angle sensor×
Removing/Installing steering components×
Removing/Installing suspension components×
Change 4 tires to new ones–
Tire rotation–
Adjusting wheel alignment×
SFIA0793E