2003 NISSAN TEANA service

FRONT DISC BRAKE
BR-27
C
D
E
G
H
I
J
K
L
MA
B
BR


It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, suspend cylinder body with wire so as not to stretch
brake hose.

Do not damage piston boot.

If any shim is subject to serious corrosion, replace it with a new one.

Always replace shim and inner shim cover as a set when replacing brake pads.

Keep rotor clean from brake fluid.

Burnish brake contact surface after refinishing or replacing rotors, after replacing pads, or it a soft
pedal occurs at very low mileage. Refer toBR-32, "
BRAKE BURNISHING PROCEDURE" .
Removal and Installation of Brake PadBFS000BZ
REMOVAL
1. Remove tyres from vehicle.
2. Remove lower sliding pin bolt.
3. Suspend cylinder body with wire, and remove pads, pad retain-
ers, shims, and shim cover from torque member.
CAUTION:
When removing pad retainers from torque member, lift pad
retainers in the direction by the arrow (shown in the figure)
so as not to damage it.
INSTALLATION
1. Apply PBC (Poly Butyl Cuprysil) grease or silicone-based
grease to the both sides of inner shim and outer shim, install
inner shim and inner shim cover to inner pad and outer shim to
outer pad.
CAUTION:
Securely install shim cover according to shim mounting
direction.
2. Install pad retainers and pads to torque member.
CAUTION:
Securely assemble pad retainers so that they are not being
lifted up from torque member.
3. Press in piston until pads can be installed, and then install cylin-
der body to torque member.
NOTE:
Using a disc brake piston tool (commercial service tool) to easily
press piston in.
CAUTION:
When replacing pads with new ones, press in piston until
pads can be installed. In this case, carefully monitor brake fluid level in reservoir tank because
brake fluid will return to master cylinder reservoir tank.
4. Install lower sliding pin bolt, and tighten it to the specified torque. Refer to BR-26, "
Components" .
5. Secure disc rotor with wheel nut. Depress brake pedal a few times until it gets a responsive touch.
6. Check front disc brake for drag.
7. Install tyres to vehicle.
SBR556E
PFIA0267E
PFIA0273E

FRONT DISC BRAKE
BR-31
C
D
E
G
H
I
J
K
L
MA
B
BR

2. Apply rubber grease to piston boot. Cover piston end with piston
boot, and install cylinder side lip on piston boot properly into a
groove on cylinder body.
CAUTION:
Do not reuse piston boot.
3. Apply brake fluid to piston, and press piston into cylinder body
by hand to assemble piston side lip on piston boot properly into
groove on piston.
CAUTION:
Press piston evenly and vary the pressing point to prevent
cylinder inner wall from being rubbed.
4. Install sliding pins and sliding pin boots to torque member.
5. Apply PBC (Poly Butyl Cuprysil) grease or silicone-based
grease to the both side of inner shim and outer shim, install
inner shim and inner shim cover to inner pad and outer shim to
outer pad.
CAUTION:
Securely install inner shim cover according to shim mount-
ing direction.
6. Install pad retainer, inner pad assembly and outer pad assembly
to torque member.
CAUTION:

Securely assemble pad retainers so that it is not being
lifted up from torque member.
7. Press in piston until pads can be installed, and then install cylinder body to torque member.
NOTE:
Use a disc brake piston tool (commercial service tool) to easily press piston in.
8. Tighten sliding pin bolts to the specified torque.BR-26, "
Components"
SFIA2498E
SFIA2279E
PFIA0267E
PFIA0273E

BR-34
REAR DISC BRAKE

WARNING:
Clean dust on caliper and brake pads with a vacuum dust collector to minimize the hazard of air borne
particles or other materials.
CAUTION:

While removing cylinder body, do never depress brake pedal because piston will pop out.

It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, hang cylinder body with wire so as not to stretch
brake hose.

Do not damage piston boot.

If any shim is subject to serious corrosion, replace it with a new one.

Always replace shims and shim covers as a set when replacing brake pads.

Keep rotor clean from brake fluid.

Burnish brake contact surface after refinishing or replacing rotors, after replacing pads, or if a soft
pedal occurs at very low mileage. Refer to BR-39, "
BRAKE BURNISHING PROCEDURE" .
Removal and Installation of Brake PadBFS000C4
REMOVAL
1. Remove tyres from vehicle.
2. Remove upper sliding pin bolt.
3. Suspend cylinder body with wire, and remove pads, pad retainers and shims, and shim covers from
torque member.
INSTALLATION
1. Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the bosh side of inner shim and outer
shin, install inner shim, inner shim cover to inner pad, and outer shim, outer shim cover to outer pad.
2. Install pad retainers and pads to torque member.
3. Press in piston until pads can be installed, and then install cylin-
der body to torque member.
NOTE:
Using a disc brake piston tool (commercial service tool) to easily
press piston in.
CAUTION:
When replacing pads with new ones, press in piston until
pads can be installed. In this case, carefully monitor brake
fluid level in reservoir tank because brake fluid will return to
master cylinder reservoir tank.
4. Install upper sliding pin bolt and tighten to the specified torque. Refer to BR-33, "
Components" .
5. Secure disc rotor with wheel nut. Depress brake pedal a few times until it gets a responsive touch.
6. Check rear disc brake for drag.
7. Install tyres to vehicle.
Refer to GI-10, "Components" and the followings for the symbols in the figure.
1: Apply rubber grease.
2: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
3: Apply polyglycol ether based lubricant.
: Apply brake fluid.
PFIA0273E

BR-38
REAR DISC BRAKE

4. Fix piston boot with retaining ring.
CAUTION:

Make sure boot is firmly in cylinder body groove on.

Do not reuse retainer ring.
5. Apply PBC (Poly Butyl Cuprysil) grease or silicone-based
grease to between shim and shim cover. Install inner shim, inner
shim cover to inner pad, and outer shim, outer shim cover to
outer pad.
6. Install pad retainers and, inner pad assembly and outer pad
assembly to torque member.
CAUTION:
Securely assemble pad retainer so that it is not being lifted
up from torque member.
7. Install sliding pin boot to torque member.
8. Press in piston until pads can be installed, and then install cylin-
der body to torque member. Use a disc brake piston tool (commercial service tool) to easily press piston
in.
9. Install cylinder body to torque member, and then tighten sliding pin bolt to the specified torque. Refer to
BR-33, "
Components" .
SFIA2280E
PFIA0273E

BR-40
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsBFS000C7
Unit: mm (in)
Brake PedalBFS000C8
Unit: mm (in)
Brake BoosterBFS000C9
Vacuum type
Check ValveBFS000CA
Front Disc BrakeBFS000CB
Unit: mm (in) Front brakeCylinder bore diameter 57.2 (2.252)
Pad length × width × thickness 125.6 × 46.0 × 11.0 (4.94 × 1.81 × 0.433)
Rotor outer diameter × thickness 296 × 24 (11.65 × 0.945)
Rear brake Cylinder bore diameter 34.93 (1.375)
Pad length × width × thickness 83.0 × 33.0 × 8.5 (3.268 × 1.299 × 0.335)
Rotor outer diameter × thickness 292 × 9 (11.50 × 0.354)
Master cylinder Cylinder bore diameter 23.8 (0.94)
Control valve Valve model Electric brake force distribution
Brake booster Booster model M215T
Diaphragm diameterPrimary 228.5 (9.0)
Secondary 203 (8.0)
Recommended brake fluid DOT 3 or DOT 4
Brake pedal height (from dash lower panel top surface) 195.8 - 205.8 (7.71 - 8.10)
Depressed brake pedal height
[under a force of 490 N (50 kg, 110 lb) with engine running]More than 115 (4.53)
Clearance between threaded end of stop lamp switch, brake
switch and/or ASCD cancel switch and bracket 0.74 - 1.96 (0.0291 - 0.0772)
Pedal play3 - 11 (0.12 - 0.43)
Input rod installation standard dimension 125 mm (4.92 in)
Vacuum leakage
[at vacuum of –66.7 kPa (–500 mmHg, –19.69 inHg)]Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 seconds
Brake padStandard thickness 11.0 (0.433)
Repair limit thickness 2.0 (0.079)
Disc rotorStandard thickness 24.0 (0.945)
Wear limit 22.0 (0.866)
Maximum uneven wear (measured at 8 positions) 0.010 (0.0004) or less
Runout limit (with it attached to vehicle) 0.040 (0.0016) or less

SERVICE DATA AND SPECIFICATIONS (SDS)
BR-41
C
D
E
G
H
I
J
K
L
MA
B
BR

Rear Disc BrakeBFS000CC
Unit: mm (in)
Brake padStandard thickness 8.5 (0.335)
Repair limit thickness 2.0 (0.079)
Disc rotorStandard thickness 9.0 (0.354)
Wear limit 8.0 (0.315)
Maximum uneven wear (measured at 8 positions) 0.015 (0.0006) or less
Runout limit (with it attached to vehicle) 0.050 (0.0020) or less

BR-42
SERVICE DATA AND SPECIFICATIONS (SDS)

BRC-1
BRAKE CONTROL SYSTEM
F BRAKES
CONTENTS
C
D
E
G
H
I
J
K
L
M
SECTION BRC
A
B
BRC

BRAKE CONTROL SYSTEM
ABS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Brake System .................................. 3
Precautions for Brake Control .................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
SYSTEM DESCRIPTION ............................................ 5
System Diagram ....................................................... 5
Functions .................................................................. 5
ABS ....................................................................... 5
EBD ....................................................................... 6
Fail-Safe Function .................................................... 6
ABS, EBD SYSTEM .............................................. 6
Hydraulic Circuit Diagram ........................................ 6
CAN Communication ................................................ 7
SYSTEM DESCRIPTION ...................................... 7
TROUBLE DIAGNOSIS .............................................. 8
How to Perform Trouble Diagnosis For Quick and
Accurate Repair ....................................................... 8
INTRODUCTION ................................................... 8
DIAGNOSIS FLOW CHART ................................. 9
ASKING COMPLAINTS ...................................... 10
EXAMPLE OF DIAGNOSIS SHEET ................... 10
Component Parts Location ...................................... 11
Schematic .............................................................. 12
Wiring Diagram — ABS — ..................................... 13
Control Unit Input/Output Signal Specifications ..... 16
REFERENCE VALUE FROM CONSULT-II ......... 16
CONSULT-II Functions (ABS) ................................ 17
CONSULT-II MAIN FUNCTION ........................... 17
CONSULT-II SETTING PROCEDURE ................ 17
Self-Diagnosis ........................................................ 17
DESCRIPTION .................................................... 17
OPERATION PROCEDURE ............................... 17
ERASE MEMORY ............................................... 17
DISPLAY ITEM LIST ........................................... 18Data Monitor ........................................................... 19
OPERATION PROCEDURE ................................ 19
DISPLAY ITEM LIST ........................................... 19
Active Test .............................................................. 20
OPERATION PROCEDURE ................................ 20
TEST ITEM .......................................................... 21
For Fast and Accurate Diagnosis ........................... 22
PRECAUTIONS FOR DIAGNOSIS ..................... 22
Basic Inspection ..................................................... 22
BRAKE FLUID LEVEL, LEAKAGE AND BRAKE
PAD ..................................................................... 22
POWER SUPPLY CIRCUIT TERMINAL LOOSE-
NESS AND BATTERY ......................................... 22
INSPECTION OF ABS WARNING LAMP AND
BRAKE WARNING LAMP ................................... 23
TROUBLE DIAGNOSIS FOR SYSTEM .................... 24
Wheel Sensor System ............................................ 24
ABS Actuator and Electric Unit (Control Unit) 1 ..... 26
ABS Actuator and Electric Unit (Control Unit) Power
Supply and Ground Circuit ..................................... 26
ABS Actuator Relay or ABS Motor Relay Power Sys-
tem .......................................................................... 28
CAN Communication System ................................. 29
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 30
Excessive ABS Function Operation Frequency ...... 30
Unexpected Pedal Action ....................................... 30
Longer Stopping Distance ...................................... 31
ABS Function Does Not Operate ............................ 31
Pedal Vibration and ABS Operation Sound Occurs ... 31
WHEEL SENSORS ................................................... 33
Removal and Installation ........................................ 33
COMPONENTS ................................................... 33
REMOVAL ........................................................... 33
INSTALLATION ................................................... 33
SENSOR ROTOR ..................................................... 34
Removal and Installation ........................................ 34
FRONT ................................................................ 34
REAR .................................................................. 34