2003 LEXUS LS430 Identifying ac

Fig. 45: Identifying Height Control Sensor Rear RH Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HEIGHT CONTROL SENSOR REAR LH: (C1714)
a. Measure the resistance according to the value (s) in the table below.
TESTER CONNECTION STANDARD SPECIFIED CONDITION
RESULT DESCRIPTION
Tester ConnectionSpecified Condition
1 (SHG) - 3 (SHB)3.0 to 5.6 Kohms
2 (SHRL) - 3 (SHB)0.4 to 3.9 Kohms
OKA
NGE

Fig. 46: Identifying Height Control Sensor Rear LH Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
B: REPLACE HEIGHT CONTROL SENSOR SUB-ASSY FRONT RH (SEE REPLACEMENT
)
C: REPLACE HEIGHT CONTROL SENSOR SUB-ASSY FRONT LH (SEE REPLACEMENT
)
D: REPLACE HEIGHT CONTROL SENSOR SUB-ASSY REAR RH (SEE REPLACEMENT
)
E: REPLACE HEIGHT CONTROL SENSOR SUB-ASSY REAR LH (SEE REPLACEMENT
)
A: REPLACE SUSPENSION CONTROL ECU (SEE REPLACEMENT
)

HINT:
When the acceleration sensor is tilted, it may output the different value.
NG: REPLACE ACCELERATION SENSOR
OK:Go to next step
4.CHECK HARNESS AND CONNECTOR (ACCELERATION SENSOR - SUSPENSION
CONTROL ECU) (SEE ELECTRONIC CIRCUIT INSPECTION PROCEDURE
)
a. Disconnect the suspension control ECU A20 or A22 connector.
b. Measure the resistance according to the value (s) in the table below.
Fig. 51: Identifying Suspension Control ECU Connector Terminals

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
TESTER CONNECTION STANDARD SPECIFIED CONDITION STANDARD (FRONT RH)
Fig. 52: Identifying Height Control Sensor Connector Terminals

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
TESTER CONNECTION STANDARD SPECIFIED CONDITION STANDARD (REAR)
Tester ConnectionSpecified Condition
A20-20 (SBR1) - H14-1 (SHB)Below 1 ohms
A20-21 (SGR1) - H14-4 (SHG)Below 1 ohms
A22-29 (SGFL) - H14-3 (SGFR)Below 1 ohms
A20-20 (SBR1) - Body ground10 Kohms or higher
A20-21 (SGR1) - Body ground10 Kohms or higher
A22-29 (SGFL) - Body ground10 Kohms or higher
Tester ConnectionSpecified Condition
A22-12 (SGR3) - A32-2 (GGND)Below 1 ohms

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE SUSPENSION CONTROL ECU (SEE REPLACEMENT
)
Fig. 53: Identifying Height Control Sensor Connector Terminals

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
A22-15 (SBR3) - A32-3 (VGS)Below 1 ohms
A22-27 (SGRR) - A32-1 (GL1)Below 1 ohms
A22-12 (SGR3) - Body ground10 Kohms or higher
A22-15 (SBR3) - Body ground10 Kohms or higher
A22-27 (SGRR) - Body ground10 Kohms or higher

Fig. 56: Identifying Absorber Control Actuator LH Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
TESTER CONNECTION STANDARD SPECIFIED CONDITION STANDARD (FRONT LH)
Tester ConnectionSpecified Condition
1 (FBL+) - 3 (GND)12.0 to 12.8 ohms
2 (FAL+) - 3 (GND)12.0 to 12.8 ohms
3 (GND) - 4 (FBL-)12.0 to 12.8 ohms
3 (GND) - 5 (FAL-)12.0 to 12.8 ohms

Fig. 57: Identifying Absorber Control Actuator RH Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
TESTER CONNECTION STANDARD SPECIFIED CONDITION STANDARD (REAR RH)
Tester ConnectionSpecified Condition
1 (RBR+) - 3 (ERR)12.0 to 12.8 ohms
2 (RAR+) - 3 (ERR)12.0 to 12.8 ohms
3 (ERR) - 4 (RBR-)12.0 to 12.8 ohms
3 (ERR) - 5 (RAR-)12.0 to 12.8 ohms

Fig. 58: Identifying Absorber Control Actuator Rear RH Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
TESTER CONNECTION STANDARD SPECIFIED CONDITION STANDARD (REAR LH)
Tester ConnectionSpecified Condition
1 (RBL+) - 3 (ERL)12.0 to 12.8 ohms
2 (RAL+) - 3 (ERL)12.0 to 12.8 ohms
3 (ERL) - 4 (RBL-)12.0 to 12.8 ohms
3 (ERL) - 5 (RAL-)12.0 to 12.8 ohms