2003 LEXUS LS430 lock

Fig. 155: Installing Spring And Temporarily Tighten Wire Adjusting Nut And Lock Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
21.INSPECT PARKING BRAKE PEDAL TRAVEL (SEE ADJUSTMENT
)
HINT:
Depress and release the parking brake pedal several times before adjusting the parking brake pedal. If the
parking brake pedal is correct at this time, tighten the parking brake wire adjusting nut.
Torque: 6.0 N.m (61 kgf.cm 53 in.lbf)
22.ADJUST PARKING BRAKE PEDAL TRAVEL (SEE ADJUSTMENT
)
23.INSTALL INSTRUMENT PANEL AIR BAG ASSY LOWER NO.1 (SEE REPLACEMENT
)
24.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSY NO.1 (SEE REPLACEMENT
)
25.INSTALL COIN BOX ASSY
26.INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSY NO.1 (SEE REPLACEMENT
)
27.INSTALL INSTRUMENT CLUSTER FINISH PANEL END (SEE REPLACEMENT
)
28.INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER LOWER (SEE
REPLACEMENT
)
29.CONNECT BATTERY NEGATIVE TERMINAL

Fig. 160: Removing Nuts, Bolts And Separate Parking Brake Cable Assy No.1 From Body
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
g. Remove the lock nut and wire adjusting nut w/spring.

Fig. 161: Removing Lock Nut And Wire Adjusting Nut W/Spring
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
h. Remove the clip from the parkin
g brake pedal assy.

Fig. 165: Installing Clip To Parking Brake Pedal Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d. Install the spring and temporarily tighten the wire adjusting nut and lock nut.

Fig. 166: Tightening Wire Adjusting Nut And Lock Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
e. Install the 3 nuts, 2 bolts and parking brake cable assy No.1 to the body.
Nuts Torque: 6 N.m (61 kgf.cm, 53 in.lbf)
Bolts Torque: 8 N.m (82 kgf.cm, 71 in.lbf)

57.INSTALL PANEL INSTRUMENT CLUSTER FINISH LOWER (SEE REPLACEMENT )
58.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER (SEE REPLACEMENT
)
59.INSTALL FRONT DOOR SCUFF PLATE LH (SEE REPLACEMENT
)
60.INSTALL INSTRUMENT PANEL FINISH PANEL (SEE REPLACEMENT
)
61.INSTALL CHOKE KNOB HOLE COVER (SEE REPLACEMENT
)
62.INSTALL GLOVE COMPARTMENT PLATE (SEE REPLACEMENT
)
63.INSTALL INSTRUMENT PANEL GARNISH SUB-ASSY LH (SEE REPLACEMENT
)
64.INSTALL FRONT SEAT ASSY LH (SEE OVERHAUL
)
65.INSTALL SEAT TRACK BRACKET COVER INNER FRONT
66.INSTALL SEAT TRACK BRACKET COVER OUTER FRONT
67.INSTALL SEAT TRACK OUTER COVER LH
68.INSTALL SEAT TRACK COVER RH
69.INSTALL SEAT BELT ANCHOR COVER CAP LH
70.REMOVE REAR WHEEL
71.ADJUST PARKING BRAKE SHOE CLEARANCE
a. Remove the hole plug.
b. Turn the adjuster and expand the shoes until the disc locks.
c. Return the adjuster 7 notches. Install the hole plug.

Fig. 181: Removing Nuts And Parking Brake Cable Assy No.3 From Rear Axle Carrier
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Remove the 3 bolts and separate the parking brake cable assy No.3.
c. Remove the parking brake cable No.3 from the parking brake intermediate lever sub-assy.
d. Remove the 2 bolts and parking brake cable No.1 clamp from the body.
e. Remove the parking brake cable No.2 clamp and No.3 clamp from the parking brake cable assy
No.3.
f. Remove the parkin
g brake cable No.5 clamp and anchor block.

Fig. 182: Removing Bolts And Parking Brake Cable No.1 Clamp From Body
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
12.INSTALL PARKING BRAKE CABLE ASSY NO.3
a. Install the parking brake cable No.5 clamp and anchor block.
b. Install the parking brake cable No.2 clamp and No.3 clamp to the parking brake cable assy No.3.
c. Place the parking brake cable No.1 clamp to the body and tighten the 2 bolts.
Torque: 6 N.m (61 kgf.cm, 53 in.lbf)
d. Attach the parking brake cable assy No.3 to the parking brake intermediate lever sub-assy.
e. Attach the parking brake cable assy No.3 to the 2 clamps and tighten bolts A, B and C.
Torque:
Bolt A: 6 N.m (61 kgf.cm, 53 in.lbf)
Bolt B, C: 19 N.m (194 kgf.cm, 14 ft.lbf)
f. Install parking brake cable assy No.3 to the rear axle carrier with the 2 nuts.
Torque: 8 N.m (81 kgf.cm, 70 in.lbf)