2003 LEXUS LS430 lock

Fig. 123: Installing Shift Lock Control ECU Sub-Assy With 2 Screws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Install the shift lever guide housing with the shift lever lock pin and a new shift lever nut.

Fig. 124: Installing Shift Lever Nut And Lock Pin After First Engaging 2 Claws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
39.INSTALL POSITION INDICATOR SLIDE COVER
a. Install position indicator slide cover No.2 to the position indicator slide cover.
b. Install the position indicator slide cover to the shift lever guide housing.

Fig. 126: Installing 3 bezel clips to position indicator housing upper
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
41.INSTALL SHIFT LOCK RELEASE BUTTON
a. Install the shift lock release button and spring to the floor shift assy.
HINT:
Securely engage the claws.
Fig. 127: Installing Shift Lock Release Button And Spring To Floor Shift Assy

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
42.INSTALL INDICATOR LAMP WIRE SUB-ASSY
a. Securely connect the 2 terminals of the indicator lamp wire harness to the transmission control
switch connector.
b. Install the position indicator lamp bulb to the indicator lamp wire sub-assy.
c. Install the position indicator bulb cap to the position indicator lamp bulb.

Fig. 132: Installing Position Indicator Housing Upper To Shift Lever Guide Housing
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
46.INSTALL SHIFT LOCK RELEASE BUTTON COVER
a. Install the shift lock release button cover to the position indicator housing upper.
47.INSTALL SHIFT LEVER KNOB SUB-ASSY
a. Install the shift lever knob sub-assy to the floor shift lever assy.

Fig. 136: Removing Nut And Disconnecting Shifting Rod From Connecting Rod Swivel
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Turn the control shaft lever of the neutral start switch counterclockwise until it stops, and turn it
clockwise 2 notches to set it to the N position.
c. Move the shift lever to the N position and tighten the nut while lightly pushing the lever toward the
R position.
d. After adjustment, check that the shift lever moves smoothly and the shift lever and gear operate
correctl
y.

3.REMOVE SEAT TRACK COVER LH
4.REMOVE SEAT TRACK BRACKET COVER OUTER FR
5.REMOVE SEAT TRACK BRACKET COVER INNER FR
6.REMOVE FRONT SEAT ASSY LH
7.REMOVE INSTRUMENT CLUSTER FINISH PANEL END
8.REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER LOWER
9.REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO.1 (SEE REPLACEMENT
)
10.REMOVE COIN BOX ASSY
11.REMOVE OUTER MIRROR SWITCH ASSY
12.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSY NO.1 (SEE REPLACEMENT
)
13.REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY No.2 (SEE REPLACEMENT
)
14.REMOVE FR DOOR SCUFF PLATE LH (SEE REPLACEMENT
)
15.REMOVE FLOOR CARPET ASSY FRONT
16.CHECK AND ADJUST BRAKE PEDAL HEIGHT
a. Check brake pedal height.
Pedal height from asphalt sheet:
165.1 to 175.1 mm (6.49 to 6.89 in.)
b. If necessary, adjust brake pedal height.
1. Disconnect the connector from the stop lamp switch assy.
2. Loosen the stop lamp switch lock nut and remove the stop lamp switch assy.
3. Loosen the push rod lock nut.
4. Adjust the pedal height by turning the pedal push rod.
5. Tighten the push rod lock nut.
Torque: 26 N.m (265 kgf.cm, 19 ft.lbf)
6. Install the stop lamp switch assy.
7. Connect the stop lamp switch assy connector.
8. Push the brake pedal in 5 to 10 mm (0.20 to 0.39 in.), and turn the stop lamp switch assy to lock the
<0051005800570003004c005100030057004b00480003005300520056004c0057004c005200510003005a004b00480055004800030057004b0048000300560057005200530003004f0044005000530003004a00520048005600030052004900490011000300
03[
9. After installation, push the brake pedal in 5 to 10 mm (0.20 to 0.39 in.), and check that the stop
lamp comes on.
10. Tighten the stop lamp switch lock nut.
Torque: 17 N.m (173 kgf.cm, 12 ft.lbf)
If the stop lamp does not come on, repeat the steps in (
b).

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
23.REMOVE BRAKE PEDAL PAD
a. Remove the brake pedal pad from the brake pedal sub-assy.
<0029004c004a0011000300150019001d000300350048005000520059004c0051004a0003002500550044004e004800030033004800470044004f0003003300440047000300290055005200500003002500550044004e004800030033004800470044004f00
03003600580045[
-Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
24.REMOVE STOP LAMP SWITCH ASSY
a. Loosen the lock nut and remove the stop lamp switch assy.
b. Remove the stop lamp switch cushion.

Fig. 29: Installing Brake Pedal Bushes To Brake Pedal Sub-Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
29.INSTALL STOP LAMP SWITCH ASSY
a. Install the stop lamp switch assy with the stop lamp switch lock nut.
Torque: 17 N.m (173 kgf.cm, 12 ft.lbf)
HINT:
After adjusting the brake pedal height, torque the lock nut.
b. Install the stop lamp switch cushion.