2003 LEXUS LS430 hood release

Fig. 60: Removing Brake Master Cylinder Sub-Assy Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5.REMOVE INSTRUMENT CLUSTER FINISH PANEL END
6.REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER LOWER
7.REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO.1 (SEE REPLACEMENT
)
8.REMOVE COIN BOX ASSY
9.REMOVE OUTER MIRROR SWITCH ASSY
10.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSY NO.1 (SEE REPLACEMENT
)
11.REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO.2
a. Remove the 2 bolts and hood lock release lever.
b. Remove the instrument panel under cover sub-assy No.2.
12.REMOVE BRAKE PEDAL RETURN SPRING
a. Remove the brake pedal return spring.
13.REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS
a. Remove the clip and the push rod pin.
b. Loosen the clevis lock nut and remove the brake master cylinder push rod clevis.
c. Remove the clevis lock nut.

Fig. 69: Installing Brake Tubes To Brake Master Cylinder Sub-Assy And ABS & TRACTION
Actuator Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
22.FILL RESERVOIR WITH BRAKE FLUID (SEE BLEEDING
)
23.BLEED MASTER CYLINDER (SEE BLEEDING
)
24.BLEED BRAKE LINE (SEE BLEEDING
)
25.CHECK FLUID LEVEL IN RESERVOIR (SEE BLEEDING
)
26.CHECK FOR BRAKE FLUID LEAKAGE
27.CHECK AND ADJUST BRAKE PEDAL HEIGHT (SEE ON
-VEHICLE INSPECTION )
28.CHECK PEDAL FREE PLAY (SEE ON
-VEHICLE INSPECTION )
29.CHECK PEDAL RESERVE DISTANCE (SEE ON
-VEHICLE INSPECTION )
30.INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSY NO.2
31.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSY NO.1
a. Install the instrument panel under cover sub-assy No.1.
b. Install the 2 bolts and hood lock release lever.
32.INSTALL OUTER MIRROR SWITCH ASSY
33.INSTALL COIN BOX ASSY
34.INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSY NO.1

FERRARI
FERRARI - IMPORTED CARS & TRUCKS
FORD MOTOR CO.
FORD MOTOR CO. - IMPORTED CARS & TRUCKS
1988-89Under Left Side Of Dash, Near Hood
Release Handle
1990-96Under Right Side Of Dash
Conquest & StarionBehind Glove Compartment
ExpoUnder Left Side Of Dash, Near Fuse/Relay
Block
MedallionOn Left Side Of Firewall
PickupUnder Left Side Of Dash, Near Fuse/Relay
Block
Ram-50Under Left Side Of Dash, Near Fuse/Relay
Block
SigmaIn Glove Compartment
Stealth
1991-98Under Left Side Of Dash, On Fuse/Relay
Block
1999Under Left Side Of Dash, Left Of Center
Console
Summit WagonUnder Right Side Of Dash
Vista WagonUnder Right Side Of Dash
ApplicationConnector Location
All Models
1996-Behind Left Side Of Dash
ApplicationConnector Location
Aspire
1994-95On Left Rear Corner Of Engine Compartment
1996-97Under Left Side Of Dash
Capri
1991Behind Right Side Of Dash, Behind Glove
Compartment
1992
1.3LOn Left Rear Corner Of Engine

1.REMOVE HOOD INSULATOR
a. Using a clip remover, disengage the 10 clips and remove the insulator.
2.REMOVE HOOD TO RADIATOR SUPPORT SEAL
a. Using a clip remover, disengage the 13 clips and remove the seal.
3.REMOVE AUXILIARY CATCH RELEASE LEVER ASSY
a. Disconnect the snap and remote control rod No. 2 in the direction indicated by the arrow marks in
the illustration.
HINT:
If snap are damaged during removal, replace them.
b. Remove the 2 bolts and lever.
Fig. 9: Removing Auxiliary Catch Release Lever Assy

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4.REMOVE RADIATOR GRILLE
a. Remove the 6 bolts and inside radiator
grille together with the outside radiator grille and radiator

c. Using a metal saw, gradually cut any area between A and B to release the gas.
Specification:
AREA MEASUREMENT
Wear protective glasses.
Cover the area being cut.
Fig. 31: Disposing Of Hood Support Assy LH

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
COMPONENTS
AreaMeasurement
a80 mm (3.15 in.)
b20 mm (0.80 in.)