2003 LEXUS LS430 lock

Fig. 190: Aligning Matchmarks On Disc And Rear Axle Hub
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
h.ADJUST PARKING BRAKE SHOE CLEARANCE
a. Remove the hole plug.
b. Turn the shoe adjuster and expand the shoes until the disc locks.
c. Return the shoe adjuster 7 notches.
d. Install the hole plug.

Fig. 202: Disconnecting Parking Brake Cable Assy No.3 From Parking Brake Shoe Lever
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
11.REMOVE PARKING BRAKE CABLE ASSY NO.3 (SEE REPLACEMENT
)
12.REMOVE PARKING BRAKE CABLE NO.5 CLAMP AND ANCHOR BLOCK
a. Remove the 2 nuts, parking brake cable No.5 clamp and anchor block.

Fig. 203: Removing Nuts, Parking Brake Cable No.5 Clamp And Anchor Block
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
13.REMOVE PARKING BRAKE CABLE NO.5 CLAMP AND ANCHOR BLOCK
a. Install the anchor block and parking brake cable No.5 clamp with 2 nuts.
Torque: 75 N.m (765 kgf.cm, 55 in. lbf)

Fig. 204: Installing Anchor Block And Parking Brake Cable No.5 Clamp With Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
14.INSTALL PARKING BRAKE CABLE ASSY NO.3 (SEE REPLACEMENT
)
15.INSTALL PARKING BRAKE SHOE LEVER SUB-ASSY LH
a. Apply high temperature grease to the parking brake shoe lever LH.
b. Install parking brake shoe lever to the parking brake cable assy No.3.

Fig. 211: Aligning Matchmarks On Disc And Rear Axle Hub
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
21.ADJUST PARKING BRAKE SHOE CLEARANCE
a. Remove the hole plug.
b. Turn the shoe adjuster and expand the shoes until the disc locks.
c. Return the shoe adjuster 7 notches.
d. Install the hole plug.

Fig. 33: Identifying DLC3 Connector terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Turn the ignition switch to the LOCK position.
b. Measure the resistance according to the value (s) in the table below.
Standard:
ECM CONNECTOR TERMINALS RESISTANCE
Tester connectionConditionSpecified valueResult
D1-6 (CANH) - D1-14
(CANL)Ignition Switch
OFF54 to 69 ohmsOK
D1-6 (CANH) - D1-14
(CANL)Ignition Switch
OFF69 ohms or more (w/o LEXUS Navigation
system)NG-A
D1-6 (CANH) - D1-14
(CANL)Ignition Switch
OFF69 ohms or more (w/ LEXUS Navigation
System)NG-B
D1-6 (CANH) - D1-14
(CANL)Ignition Switch
OFF54 ohms or less (w/o LEXUS Navigation
System)NG-C

Fig. 38: Check Can Bus Line For Disconnection
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Turn the ignition switch to the LOCK position.
b. Disconnect the skid control ECU connector (S42).
c. Measure the resistance according to the value (s) in the table below.
Standard:
SKID CONTROL ECU CONNECTOR TERMINALS RESISTANCE
NG: REPAIR OR REPLACE SKID CONTROL ECU SUB BUS LINE OR CONNECTOR (CAN-
H, CAN-L)
OK: GO TO NEXT STEP
2.CHECK WIRE HARNESS (IG, GND1, GND2)
Tester ConnectionConditionSpecified value
S42-11 (GANH) - S42-25 (CANL)Ignition Switch OFF54 to 69 ohms

a. Turn the ignition switch to the LOCK position.
b. Disconnect the steering sensor connector (S16).
c. Measure the resistance according to the value (s) in the table below.
Standard:
STEERING SENSOR CONNECTOR TERMINALS RESISTANCE
NG: REPAIR OR REPLACE STEERING SENSOR SUB BUS LINE OR CONNECTOR (CAN-H,
CAN -L)
OK: GO TO NEXT STEP
2.CHECK WIRE HARNESS (IG1, ESS)
Tester ConnectionConditionSpecified value
S16-10 (CANH) -S16-9 (CANL)Ignition Switch OFF54 to 69 ohms