2001 TOYOTA SEQUOIA brake sensor

DI±600
± DIAGNOSTICSAUTOMATIC TRANSMISSION
794 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0724 Brake Switch ºBº Circuit High
CIRCUIT DESCRIPTION
The purpose of this circuit is to prevent the engine from stalling while driving in lock±up condition when
brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the opera-
tion of the lock±up clutch while braking is in progress.
DTC No.DTC Detection ConditionTrouble Area
P0724
The stop light switch remains ON even when the vehicle is
driven in a STOP (less than 3 km/h (2 mph)) and GO (30 km/h
(19 mph) or more) fashion 5 times. (2±trip detection logic).
Short in stop light switch signal circuit

Stop light switch

ECM
MONITOR DESCRIPTION
This DTC indicates that the stop light switch remains on. When the stop light switch remains ON during ºstop
and goº driving, the ECM interprets this as a fault in the stop light switch and the MIL comes on and the ECM
stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) ten
times for two driving cycles in order to detect a malfunction.
MONITOR STRATEGY
Related DTCsP0724Stop light switch/Range check/Rationality
Rid /C tMainStop light switchRequired sensors/ComponentsSubVehicle speed sensor
Frequency of operationContinuous
DurationGO and STOP 5 times
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not present.See page DI±545
Battery voltage8 V or more±
Ignition switchON
StarterOFF
GO (Vehicle speed is 30 km/h
(18.63 mph) or more)Once
STOP (Vehicle speed is less than 3 km/h
(1.86 mph))Once
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Brake switchRemain ON during GO and STOP 5 times
DIDJA±01

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±601
795 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
See page DI±283.
INSPECTION PROCEDURE
1 Read value of DATA LIST (STP signal).
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
Standard:
ItemMeasurement Item/
Range (display)Normal Condition
Stop Light SwitchStop light SW Status/
ON or OFF
Brake Pedal is depressed: ON

Brake Pedal is released: OFF
NOTICE:
In the table above, the conditions listed under ºNormal Conditionº are reference conditions. Do not
depend solely on these reference conditions when deciding whether a part is faulty or not.
OK:
Brake Pedal ConditionSpecified Condition
DepressedON
ReleasedOFF
NG Go to step 2.
OK
Go to step 3.

DI±608
± DIAGNOSTICSAUTOMATIC TRANSMISSION
802 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0751 Shift Solenoid ºAº Performance
(Shift Solenoid Valve S1)
SYSTEM DESCRIPTION
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.DTC Detection ConditionTrouble Area
P0751The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Shift solenoid valve S1 remains open or closed

Valve body is blocked

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates ºstuck ON malfunctionº or ºstuck OFF malfunctionº of the shift solenoid valve S1.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº. When the gear position com-
manded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores
the DTC.
MONITOR STRATEGY
RltdDTCP0751Shift solenoid valve S1/OFF malfunctionRelated DTCsP0751Shift solenoid valve S1/ON malfunction
MainShift solenoid valve S1
Required sensors/ComponentsSubVehicle speed sensor, Throttle position sensor, Speed sensor (NT), Speed
sensor (NO)
Frequency of operationContinuous
OFF malfunction (A) and (B)0.4 sec.
OFF malfunction (C)Immediate
DurationON malfunction (A), (B) and
(C)0.4 sec.
ON malfunction (D)3 sec.
ON malfunction (E)0.5 sec.
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
DIDJC±01

DI±614
± DIAGNOSTICSAUTOMATIC TRANSMISSION
808 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0756 Shift Solenoid ºBº Performance
(Shift Solenoid Valve S2)
SYSTEM DESCRIPTION
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.DTC Detection ConditionTrouble Area
P0756The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Shift solenoid valve S2 remains open or closed

Valve body is blocked

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates ºstuck ON malfunctionº or ºstuck OFF malfunctionº of the shift solenoid valve S2.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº. When the gear position com-
manded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores
the DTC.
MONITOR STRATEGY
RltdDTCP0756Shift solenoid valve S2/OFF malfunctionRelated DTCsP0756Shift solenoid valve S2/ON malfunction
MainShift solenoid valve S2
Required sensors/ComponentsSubVehicle speed sensor, Throttle position sensor, Speed sensor (NT), Speed
sensor (NO)
Frequency of operationContinuous
OFF malfunction (A), (B), (C)0.4 sec.
OFF malfunction (D)Immediate
DurationON malfunction (A) and (B)0.4 sec.Duration
ON malfunction (C)3 sec.
ON malfunction (D)0.5 sec.
MIL operation2 driving cycles
Sequence of operationNone
DIDJD±01

DI±620
± DIAGNOSTICSAUTOMATIC TRANSMISSION
814 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0771 Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
SYSTEM DESCRIPTION
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.DTC Detection ConditionTrouble Area
P0771The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)

Shift solenoid valve SR remains open or closed

Shift solenoid valve SL1 remains open or closed

Valve body is blocked

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates ºstuck ON malfunctionº or ºstuck OFF malfunctionº of the shift solenoid valve SR or SL1.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº. When the gear position com-
manded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores
the DTC.
MONITOR STRATEGY
Related DTCsP0771Shift solenoid valve SR/Rationality check
Rid /C tMainShift solenoid valve SRRequired sensors/ComponentsSubSpeed sensor (NT), Speed sensor (NO), Crankshaft position sensor (NE)
Frequency of operationContinuous
OFF malfunction (A)0.4 sec.
DurationOFF malfunction (B) and (C)ImmediateDuration
ON malfunction0.15 sec.
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
DIDJE±01

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±625
819 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0776 Pressure Control Solenoid ºBº Performance
(Shift Solenoid Valve SL2)
SYSTEM DESCRIPTION
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.DTC Detection ConditionTrouble Area
P0776The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)Shift solenoid valve SL2 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates ºstuck ON malfunctionº or ºstuck OFF malfunctionº of the shift solenoid valve SL2.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº. When the gear position com-
manded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores
the DTC.
MONITOR STRATEGY
Related DTCsP0776Shift solenoid valve SL2/ON malfunction
Rid /C tMainShift solenoid valve SL2Required sensors/ComponentsSubSpeed sensor (NT), Speed sensor (NO), Crankshaft position sensor (NE)
Frequency of operationContinuous
ON malfunctions (A), (B) and
(C)0.4 sec.
DurationON malfunction (D)3 sec.
ON malfunction (E)0.5 sec.
MIL operation2 driving cycles
Sequence of operationNone
DIDJF±01

D14169
1±2 Shift Valve
Valve Body:
DI±636
± DIAGNOSTICSAUTOMATIC TRANSMISSION
830 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0781 1±2 Shift (1±2 Shift Valve)
SYSTEM DESCRIPTION
The 1±2 shift valve performs shifting to 1st gear and other
gears.
DTC No.DTC Detection ConditionTrouble Area
P0781The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Valve body is blocked up or stuck (1±2 shift valve)

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates that the 1±2 shift valve in the valve body is locked in the direction the spring compresses.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº and switching oil pressure
to the valves in the valve body.
The ECM calculates the ºactualº transmission gear by comparing the signals from the input speed sensor
(NCO) and the output speed sensor (SP2). The ECM can detect many mechanical problems in the shift sole-
noids, valve body, and the transmission clutches, brakes, and gears. If the ECM detects that the actual gear
position and the commanded gear position are different, it will illuminate the MIL and store the DTC .
MONITOR STRATEGY
Related DTCsP0781Valve body/Rationality check
MainValve body
Required sensors/ComponentsSubAutomatic transmission assembly, Speed sensor (NT), Speed sensor
(NO), Vehicle speed sensor, Throttle speed sensor
Frequency of operationContinuous
Conditions (A) and (B)0.4 sec.
DurationCondition (C)3 sec.Duration
Condition (D)0.5 sec.
MIL operation2 driving cycles
Sequence of operationNone
DIDJH±01

D14171
Line Pressure
Control Pressure
Current Flow to Solenoid
D14172
ON
OFF
1 cycle
D14173
DI±656
± DIAGNOSTICSAUTOMATIC TRANSMISSION
850 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2714 Pressure Control Solenoid ºDº Performance
(Shift Solenoid Valve SLT)
SYSTEM DESCRIPTION
The linear solenoid valve (SLT) controls the transmission line
pressure for smooth transmission operation based on signals
from the throttle position sensor and the vehicle speed sensor.
The ECM adjusts the duty cycle of the SLT solenoid valve to
control hydraulic line pressure coming from the primary regula-
tor valve. Appropriate line pressure assures smooth shifting
with varying engine outputs.
(*): Duty Ratio
The duty ratio is the ratio of the period of continuity in one cycle.
For example, if A is the period of continuity in one cycle, and B
is the period of non±continuity, then
Duty Ratio = A/(A + B) x 100 (%)
DTC No.DTC Detection ConditionTrouble Area
P2714
ECM detects a malfunction on SLT (ON side) according to the
revolution difference of the turbine and the output shaft, and
also by the oil pressure. (2±trip detection logic)
Shift solenoid valve SLT remains open or closed

Valve body is blocked

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
The ECM calculates the amount of heat absorbed by the friction material based on the difference in revolu-
tion (clutch slippage) between the turbine and output shaft. The ECM turns on the MIL and outputs this DTC
when the amount of heat absorption exceeds the specified value.
When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force de-
creases.
NOTE: If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer
be drivable.
DIDJL±01