2001 TOYOTA SEQUOIA brake sensor

D14175
G23415D14176
Lock±up
Operation
Pressure
Current Flow to Solenoid DI±672
± DIAGNOSTICSAUTOMATIC TRANSMISSION
866 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2757Torque Converter Clutch Pressure Control Solenoid
Performance(Shift Solenoid Valve SLU)
SYSTEM DESCRIPTION
The ECM uses the signals from the throttle position sensor, Air±
flow meter, turbine (input) speed sensor, output speed sensor
and crankshaft position sensor to monitor the engagement
condition of the lock±up clutch.
Then the ECM compares the engagement condition of the
lock±up clutch with the lock±up schedule in the ECM memory
to detect a mechanical problems of the shift solenoid valve
SLU, valve body and torque converter clutch.
DTC No.DTC Detection ConditionTrouble Area
P2757
Lock±up does not occur when driving in the lock±up range
(normal driving at 80 km/h [50 mph]), or lock±up remains ON
in the lock±up OFF range.
(2±trip detection logic)
Shift solenoid valve SLU remains open or closed

Valve body is blocked

Torque converter clutch

Automatic transmission (clutch, brake or gear, etc.)

Line pressure is too low
DIDJO±01

DIDDE±01
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±727
921 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
By accessing the DATA LIST displayed by the hand±held tester, you can read the value of the switches and
sensors and so on without removing any parts. Reading the DATA LIST is the first step of troubleshooting
and is one method to shorten labor time.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Following the display on the tester, read the DATA LIST.
AIR SUSPENSION:
ItemMeasurement Item / Range (Dis-
play)Normal ConditionDiagnostic Note
VEHICLE SPD
Vehicle speed reading / min.: 0
km/h (0 mph), max.: 255 km/h
(158 mph)
Actual vehicle speedSpeed indicated on the combina-
tion meter
FR WHEEL SPD
Wheel speed (Front right) reading /
min.: 0 km/h (0 mph), max.: 255
km/h (159 mph)
Actual vehicle speedSpeed indicated on the speedome-
ter
FL WHEEL SPD
Wheel speed (Front left) reading /
min.: 0 km/h (0 mph), max.: 255
km/h (159 mph)
Actual vehicle speedSpeed indicated on the speedome-
ter
IG VOLTAGEECU power supply voltage / min.:
0 V, max.: 25.5 VActual ECU power supply voltage:
10 to 14 V±
POWER VOLTAGE+B power source voltage / min.: 0
V, max.: 25.5 VActual battery power supply volt-
age: 10 to 14 V±
STEERING ANG
Steering angle sensor reading /
min.: ±49150.5 deg, max.: 49152
degActual steering angle /
Left turn: reading increases
Right turn: reading increasesZero point is set at the point when
battery is connected
ENGINE SPDCrankshaft position sensor read-
ing / min.: 0 rpm, max.: 25,500 rpmActual engine speedSpeed indicated on the combina-
tion meter
HEIGHT SW DOWNHeight control switch (DOWN) /
ON or OFFON: Height control switch
ºDOWNº button pressed
OFF: ±
±
HEIGHT SW UPHeight control switch (UP) / ON or
OFFON: Height control switch ºUPº
button pressed
OFF: ±
±
HEIGHT SW HOLDHeight control mode select switch
/ ON or OFFON: Height control mode select
switch pressed
OFF: ±
±
STOP LIGHT SWStop light switch / ON or OFFON: Brake pedal depressed
OFF: Brake pedal released±
DOOR SWDoor courtesy light switch / ON or
OFFON: Open each door
OFF: Close all doors±
L4 SW4LO switch / ON or OFFON: 2WD/4HI switch pressed
OFF: ±±
TSTS terminal / ON or OFFON: During test mode
OFF: Normal mode±
TCTC terminal / ON or OFFON: DTC recorded
OFF: No DTC recorded±
SOL SLRLHeight control valve solenoid (Lev-
elling solenoid valve) / ON or OFFON: Leveling solenoid operated
OFF: Leveling solenoid not oper-
ated
±
SOL SLRGHeight control valve solenoid
(Gate solenoid valve) / ON or OFFON: Gate solenoid operated
OFF: Gate solenoid not operated±

F19446
W
41G±Y1
4A11
4AG±Y27
S25 STP
BatteryB ALT
85 W 1
1L STOP 2
1FS14
Stop Light Switch
Sub J/B No. 4Suspension Control
ECU
Instrument Panel J/BF10
Fusible Link Block
1L
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±767
961 Author: Date:
2005 SEQUOIA (RM1146U)
DTC C1782/82 Stop Light Switch Circuit (Test Diagnosis)
CIRCUIT DESCRIPTION
When the brake pedal is depressed, the stop light comes on and the signal is input to the STP terminal of
the suspension control ECU.
HINT:
This DTC is output only when the sensor signal check is done.
DTC No.DTC Detecting ConditionTrouble Area
C1782/82The signal from the stop light switch assy does not change.

Stop light switch assy

Stop light switch circuit

Suspension control ECU
WIRING DIAGRAM
DIDE7±01

DIDLV±01
F17996
Front Speed SensorABS & VSC Actuator
(w/ Skid Control ECU)Level Warning Switch
Rear Speed Sensor Rear Speed Sensor Rotor
Front Speed
Sensor Rotor
Parking Brake SwitchStop Light Switch
Center Diff. Lock Switch *1
TRAC OFF Switch *2
Steering Angle Sensor
DLC3Brake Inhibit RelayTranslate ECU
VSC BuzzerBrake Booster
(Including Active Brake Booster
Solenoid, Delta S Sensor and Boost-
er Pedal Switch)
Master Cylinder
Pressure Sensor
Front Speed Sensor Rotor
Front Speed Sensor
Yaw Rate Sensor
(Including Deceleration Sensor)
ABS Warning Light
VSC TRAC Warning light
VSC OFF Indicator Light *
1
TRAC OFF Indicator Light *2
BRAKE Warning Light
SLIP Indicator Light
*1: Only for 4WD
*2: Only for 2WDCenter Diff. Lock
Position Switch
DI±892
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1086 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DIDLW±01
F19153
Speed Sensor
(Each Wheel)
Stop Lamp Switch
Parking Brake Switch
Delta S Sensor
Yaw Rate
(Deceleration) SensorABS & VSC Actuator
Skid Control
ECUCombination
Meter
Translate
ECUSteering Angle
Sensor
4WD ECU
ECM
CAN Communication SystemAir Suspension ECU (*1): CAN1 Circuit
(*2): CAN2 Circuit
(*3): Vehicle CAN Circuit(*2)
(*3) (*1)
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±893
1087 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

DIDLX±01
DI±894
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1088 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. SYSTEM DESCRIPTION
HINT:

The yaw rate sensor and deceleration sensor are combined and in a single unit. This unit communi-
cates with the skid control ECU through the CAN communication system.

No changes have been made to the communication method between the VSC system and ECM. How-
ever, the communication method between the Translate ECU and ECM has been changed from serial
to CAN communication.
(a) ABS
(Anti±lock Brake System)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking
on a slippery surface.
(b) EBD
(Electronic Brake force Distribution)
The EBD control utilizes ABS, realizing proper brake force distribution between front and rear wheels
in accordance with driving conditions.
In addition, during braking while cornering, it also controls the brake forces of the right and left wheels,
helping to maintain vehicle behavior.
(c) BA (Brake Assist)
The primary purpose of the brake assist system is to provide an auxiliary brake force to assist the driver
who cannot generate a large enough brake force during emergency braking, thus helping to maximize
the vehicle's braking performance.
(d) TRAC
(Traction Control)
The TRAC system helps prevent the drive wheels from slipping if the driver presses down on the accel-
erator pedal excessively when starting off or accelerating on a slippery surface.
(e) VSC
(Vehicle Stability Control)
The VSC system helps prevent the vehicle from slipping sideways as a result of strong front wheel skid
or strong rear wheel skid during cornering.
2. ABS with EBD & BA & TRAC & VSC OPERATION
(a) The skid control ECU calculates vehicle stability tendency based on signals from the speed sensor,
yaw rate (deceleration) sensor and steering angle sensor. In addition, it evaluates the results of the
calculations to determine whether any control actions (control of the engine output torque by electronic
throttle control and of the wheel brake pressure by the brake actuator) should be implemented.
(b) The SLIP indicator blinks and the VSC buzzer sounds to inform the driver that the VSC system is oper-
ating. The SLIP indicator also blinks when TRAC is operating, and the operation being performed is
displayed.
3. FAIL SAFE FUNCTION
(a) When a failure occurs in the ABS & BA & TRAC & VSC systems, the ABS and VSC warning lights come
on and ABS & BA & TRAC & VSC operations are prohibited. In addition to this, when there is a failure
that disables EBD operation, the brake warning light also comes on and EBD operation is prohibited.
(b) If some control is prohibited due to a malfunction during its operation, that control will be cut off gradual-
ly not to change the stability of the vehicle suddenly.

DIDLY±01
F09750
DLC3
Ts
Tc
CG
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±897
1091 Author: Date:
2005 SEQUOIA (RM1146U)
CALIBRATION
1. ZERO POINT CALIBRATION OF MASTER CYLINDER
PRESSURE, YAW RATE AND DECELERATION SEN-
SORS
HINT:
When having replaced the master cylinder pressure, yaw rate
and deceleration sensors and/or the ECU, make sure to per-
form master cylinder pressure, yaw rate and deceleration sen-
sors' zero point calibration.
NOTICE:

While obtaining the zero point, do not vibrate the ve-
hicle by tilting, moving or shaking it and keep it in a
stationary condition. (Do not start the engine.)

Be sure to do this on a level surface (within an inclina-
tion of 1 degree).
(a) Perform master cylinder pressure, yaw rate and decelera-
tion sensors zero point calibration.
(1) Using SST, connect terminals Ts and CG of the
DLC3.
SST 09843±18040
(2) Shift the shift lever to the P position.
(3) Turn the ignition switch to the ON position.
(4) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
(5) Keep your foot off the brake pedal.
Do not leave 4WD vehicles in the L4 position.
(6) Press the center diff. lock (TRAC OFF) switch 3
times within 3 seconds.
(7) Check that the VSC buzzer sounds for 3 seconds.
HINT:

If the VSC buzzer does not sound, do the zero point cal-
ibration again and/or check the VSC buzzer circuit (See
page DI±1052).

If the VSC buzzer does not sound, check for yaw rate and
deceleration sensor failure (See page DI±911).
(8) Turn the ignition switch OFF.
(9) Disconnect terminals Ts and CG of the DLC3.
(b) Perform steering angle sensor zero point calibration.
This calibration is carried out automatically by following
procedures below:
(1) Make sure the system is not in sensor check mode.
(2) Calibrate the steering angle sensor by driving the
vehicle in a straight line at more than 7 MPH (12
km/h) for 5 seconds.

F02135
Start Position
End PositionWithin ± 5° DI±900
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1094 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Check the yaw rate and deceleration sensor.
Shift the shift lever to the D position and drive the vehicle
at a vehicle speed of approx. 3 mph (5 km/h), turn the
steering wheel either to the left or right for 90° or more,
and turn the vehicle through 180 degrees. Check that the
VSC buzzer sounds for 3 seconds upon start off.
Stop the vehicle and shift the shift lever to the P position,
and check that the VSC buzzer sounds again for 3 se-
conds.
HINT:

If the VSC buzzer sounds twice, the sensor check has
been completed normally.

If the VSC buzzer does not sound, check the VSC buzzer
circuit (See page DI±1052), then do the sensor check
again.

Drive the vehicle through 180°. At the end of the turn, the
direction of the vehicle should be within 180° ± 5° of its
start position.

Do not spin the wheels.

If the buzzer sounds after start off, then the deceleration
sensor check has passed its check. If the buzzer sounds
at the completion of a curve, then the yaw rate sensor
check has passed its check. The buzzer sound should be
heard twice during the sensor checks.
(c) Check the master cylinder pressure sensor.
(1) Turn the ignition switch to the ON position.
(2) Keep the vehicle in a stationary condition on a level
surface for 2 sec. or more.
(3) Keeping the vehicle in a stationary condition and
not pressing on the brake pedal for 1 sec. or more,
depress the brake pedal with 147 N (15 kgf, 33 lbf)
or more for 2 sec. or more.
NOTICE:
If zero point calibration has never been performed on a new
ECU, master cylinder pressure sensor check cannot be
completed correctly. Perform zero point calibration first
(See page DI±897).
HINT:
At this time, the buzzer sounds for 3 seconds.
(d) Check the speed sensor.
Drive the vehicle straight forward.
When driving the vehicle at the speed of 28 mph (45 km/h)
or higher for several seconds, check that the ABS warn-
ing light goes off.
HINT:
There is a possibility that the sensor check is not completed if
the vehicle has its wheels spun or its steering wheel turned dur-
ing this check.
(e) Stop the vehicle.