2001 TOYOTA SEQUOIA brake sensor

DI±66
± DIAGNOSTICSENGINE
260 Author: Date:
2005 SEQUOIA (RM1146U)P043E
(DI±445)
Evaporate Emission System
Reference Orifice Clog Up
Pump module
P043F
(DI±445)Evaporate Emission System
Reference Orifice High Flow
Pump module
P0441
(DI±257)Evaporative Emission Control
System Incorrect Purge Flow

Purge valve

Purge valve circuit (between purge valve and ECM)

Leakage from EVAP line (between purge valve and intake
manifold)

EVAP line (between purge valve and canister) clogged

ECM

P0450
(DI±264)Evaporative Emission Control
System Pressure Sensor/Switch
[Fuel Tank Pressure Sensor]

Pump module (including pressure sensor)
P0451
(DI±264)Evaporative Emission Control
System Pressure Sensor/Switch
Range/Performance

Pump module (including pressure sensor)
P0452
(DI±264)Evaporative Emission Control
System Pressure Sensor/Switch
Low Input
Pump module (including pressure sensor)

Connector/Wire harness (between pump module and ECM)

ECM

P0453
(DI±264)Evaporative Emission Control
System Pressure Sensor/Switch
High Input
Pump module (include pressure sensor)

Connector/Wire harness (between pump module and ECM)

ECM

P0455
(DI±273)Evaporative Emission Control
System Leak Detected (Gross
Leak)

Fuel tank cap (loose)

Leakage from EVAP line (between canister and fuel tank)

Leakage from EVAP line (between purge valve and canister)

Leakage from pump module

Leakage from fuel tank

Leakage from canister

P0456
(DI±273)Evaporative Emission Control
System Leak Detected (Very
Small Leak)

Same as DTC No. P0445
P0500
(DI±278)Vehicle Speed Sensor ºAº

Combination meter

Open or short in vehicle speed sensor circuit

Vehicle speed sensor

ECM

P0503
(DI±278)Vehicle Speed Sensor ºAº Inter-
mittent/Erratic/High

Combination meter

Open or short in vehicle speed sensor circuit

Vehicle speed sensor

ECM
±
P0504
(DI±283)Brake Switch ºAº/ºBº Correlation

Short in stop lamp switch signal circuit

STOP fuse

Stop lamp switch

ECM
±
P0505
(DI±288)Idle Air Control System

Air induction system

Electric throttle control system

PCV hose connection

P0560
(DI±292)System Voltage

Back±up power source circuit

EFI No. 1 fuse

ECM

P0604
(DI±296)Internal Control Module Random
Access Memory (RAM) Error
ECM
P0606
(DI±296)ECM/PCM Processor
ECM
P0607
(DI±296)Control Module Performance
ECM

± DIAGNOSTICSENGINE
DI±67
261 Author: Date:
2005 SEQUOIA (RM1146U)P0617
(DI±298)
Starter Relay Circuit High

Park/neutral position switch

Starter relay circuit

Ignition switch

ECM

P0630
(DI±302)VIN not Programmed or Mis-
match±ECM/PCM
ECM
P0657
(DI±296)Actuator Supply Voltage Circuit/
Open
ECM
P0705
(DI±576)Transmission Range Sensor Cir-
cuit Malfunction (PRNDL Input)
Electronic Controlled Automatic Transaxle (ECT)
P0710
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit
Electronic control automatic transmission (ECT)
P0711
(DI±588)Transmission Fluid Temperature
Sensor ºAº Performance
Electronic control automatic transmission (ECT)
P0712
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit Low Input
Electronic control automatic transmission (ECT)
P0713
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit High Input
Electronic control automatic transmission (ECT)
P0717
(DI±591)Input/Turbine Speed Sensor ºAº
Circuit No Signal
Electronic control automatic transmission (ECT)
P0722
(DI±596)Output Speed Sensor Circuit No
Signal
Electronic control automatic transmission (ECT)
P0724
(DI±600)Brake Switch ºBº Circuit High
Electronic control automatic transmission (ECT)
P0748
(DI±603)Pressure Control Solenoid ºAº
Electrical (Shift Solenoid Valve
SL1)

Electronic control automatic transmission (ECT)
P0751
(DI±608)Shift Solenoid ºAº Performance
(Shift Solenoid Valve S1)
Electronic control automatic transmission (ECT)
P0756
(DI±614)Shift Solenoid ºBº Performance
(Shift Solenoid Valve S2)
Electronic control automatic transmission (ECT)
P0771
(DI±620)Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
Electronic control automatic transmission (ECT)
P0776
(DI±625)Pressure Control Solenoid ºBº
Performance (Shift Solenoid
Valve SL2)

Electronic control automatic transmission (ECT)
P0778
(DI±631)Pressure Control Solenoid ºBº
Electrical (Shift Solenoid Valve
SL2)

Electronic control automatic transmission (ECT)
P0781
(DI±636)1±2 Shift (1±2 Shift Valve)
Electronic control automatic transmission (ECT)
P0973
(DI±641)Shift Solenoid ºAº Control Circuit
Low (Shift solenoid Valve S1)
Electronic control automatic transmission (ECT)
P0974
(DI±641)Shift Solenoid ºAº Control Circuit
High (Shift solenoid Valve S1)
Electronic control automatic transmission (ECT)
P0976
(DI±646)Shift Solenoid ºBº Control Circuit
Low (Shift solenoid Valve S2)
Electronic control automatic transmission (ECT)
P0977
(DI±646)Shift Solenoid ºBº Control Circuit
High (Shift solenoid Valve S2)
Electronic control automatic transmission (ECT)
P0985
(DI±651)Shift Solenoid ºEº Control Circuit
Low (Shift Solenoid Valve SR)
Electronic control automatic transmission (ECT)

A23662
40 mph (64 km/h)
Idling
IG SW OFF ECT:
75C (167F) or higher
Vehicle Speed
Warming up(d)(f)
10 minutes
or more(g)
10 seconds
or more4 seconds
or moreTime At Least 3 times
(h) (i)
(j) Accelerator Pedal
DepressedAccelerator Pedal
Released (Fuel±cut)
DI±390
± DIAGNOSTICSENGINE
584 Author: Date:
2005 SEQUOIA (RM1146U)
CONFIRMATION DRIVING PATTERN
HINT:
This confirmation driving pattern is used in steps 2, 4, 7, 17 and 21 of the following diagnostic troubleshooting
procedure when using a hand±held tester.
(a) Connect the hand±held tester to DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Clear DTCs (see page DI±43).
(d) Start the engine, and warm it up until the ECT reaches 75C (167F) or higher.
(e) On the hand±held tester, select the following menu items: DIAGNOSIS/ENHANCED OBD II/DATA
LIST/FC IDL.
(f) Drive the vehicle at 40 mph (64 km/h) or more for at least 10 minutes.
(g) Change the transmission to 2nd gear.
(h) Drive the vehicle at proper vehicle speed to perform fuel±cut operation.
HINT:
Fuel±cut is performed under following conditions met:

Accelerator pedal fully released.

Engine speed 2,500 rpm or more (fuel injection returns at 1,000 rpm).
(i) Accelerate the vehicle to 30 mph (48 km/h) or more by depressing the accelerator pedal for at least
10 seconds.
(j) Soon after performing step (8) above, release the accelerator pedal for at least 4 seconds without de-
pressing the brake pedal, in order to execute fuel±cut control.
(k) Stop the vehicle and allow the engine to idle for 10 seconds or more.
(l) Allow the vehicle to decelerate until the vehicle speed declines to less than 6 mph (10 km/h).
(m) Repeat steps from (8) through (10) above at least 3 times in one driving cycle.
HINT:
Completing all A/F sensor monitors are required to change the value in TEST RESULT.
CAUTION:
Strictly observe of posted speed limits, traffic laws, and road conditions when performing these
drive pattern.

DIDJ3±01
DI±570
± DIAGNOSTICSAUTOMATIC TRANSMISSION
764 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal ConditionDiagnostic Note
STOP LIGHT SWStop light SW Status/
ON or OFF
Brake Pedal is depressed: ON

Brake Pedal is released: OFF±
PNP SW [NSW]PNP SW Status/
ON or OFFShift lever position is;
P and N: ON
Except P and N: OFF
When the shift lever position dis-
played on the hand±held tester dif-
fers from the actual position, ad-
justment of the PNP switch or the
shift cable may be incorrect.
HINT:
When the failure still occurs even
after adjusting these parts,
See page DI±576.
LOWPNP SW Status/
ON or OFF

Shift lever position is 2: OFF
O

Shift position L switch Push: ON
O

Shift position L switch Push: OFF
=
2NDPNP SW Status/
ON or OFFShift lever position is;
2 and L: ON
Except 2 and L: OFF
=
3RDPNP SW Status/
ON or OFFShift lever position is;
3: ON
Except 3: OFF
=
DRIVEPNP SW Status/
ON or OFFShift lever position is;
D: ON
Except D: OFF
=
REVERSEPNP SW Status/
ON or OFFShift lever position is;
R: ON
Except R: OFF
=
OVERDRV CUT SW2O/D SW Status/
ON or OFF

IG SW ON: ON
O

O/D SW Push: OFF
O

O/D SW Push: ON
±
SHIFTActual Gear Position/
1st, 2nd, 3rd, 4th or 5th
Shift lever position is;

L: 1st

2: 1st or 2nd

3: 1st, 2nd or 3rd

4(O/D OFF): 1st, 2nd, 3rd or 4th

D: 1st, 2nd, 3rd, 4th or 5th
±

DIDJ4±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±573
767 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the parts listed in the table below and proceed to the page
given.
HINT:
*1 :
... The MIL (Malfunction Indicator Lamp) lights up
*2 :  ... The ECM memorizes the trouble code if the ECM detects the DTC detection condition.
This DTC may be output when the clutch, brake and gear components etc. inside the automatic trans-
mission are damaged.
DTC No.
(See Page)Detection ItemTrouble AreaMIL *1Memory *2
P0500
(DI±278)Vehicle Speed Sensor ºAº
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM


P0705
(DI±576)Transmission Range Sensor Cir-
cuit Malfunction (PRNDL Input)Open or short in park/neutral position switch circuit
Park/neutral position switch
ECM


P0710
(DI±582)Transmission Fluid Temperature
Sensor ºAº CircuitOpen or short in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0711
(DI±588)Transmission Fluid Temperature
Sensor ºAº PerformanceTransmission wire (ATF temperature sensor No.1)

P0712
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit Low InputShort in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0713
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit High InputOpen in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0717
(DI±591)Input Speed Sensor Circuit No
Signal
Open or short in speed sensor (NT) circuit
Speed sensor (NT)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0722
(DI±596)Output Speed Sensor Circuit No
Signal
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0724
(DI±600)Brake Switch ºBº Circuit High
Short in stop light switch signal circuit
Stop light switch
ECM


P0748
(DI±603)Pressure Control Solenoid ºAº
Electrical
(Shift Solenoid Valve SL1)Open or short in shift solenoid valve SL1 circuit
Shift solenoid valve SL1
ECM


P0751
(DI±608)Shift Solenoid ºAº Performance
(Shift Solenoid Valve S1)Shift solenoid valve S1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0756
(DI±614)Shift Solenoid ºBº Performance
(Shift Solenoid Valve S2)Shift solenoid valve S2 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0771
(DI±620)Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
Shift solenoid valve SR remains open or closed
Shift solenoid valve SL1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)



DI±574
± DIAGNOSTICSAUTOMATIC TRANSMISSION
768 Author: Date:
2005 SEQUOIA (RM1146U)P0776
(DI±625)
Pressure Control Solenoid ºBº
Performance
(Shift Solenoid Valve SL2)Shift solenoid valve SL2 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0778
(DI±631)Pressure Control Solenoid ºBº
Electrical
(Shift Solenoid Valve SL2)Open or short in shift solenoid valve SL2 circuit
Shift solenoid valve SL2
ECM


P0781
(DI±636)1±2 Shift (1 ±2 Shift Valve)Valve body is blocked up or stuck (1±2 shift valve)
Automatic transmission (clutch, brake or gear, etc.)

P0973
(DI±641)Shift Solenoid ºAº Control Circuit
Low (Shift Solenoid Valve S1)Short in shift solenoid valve S1 circuit
Shift solenoid valve S1
ECM


P0974
(DI±641)Shift Solenoid ºAº Control Circuit
High (Shift Solenoid Valve S1)Open in shift solenoid valve S1 circuit
Shift solenoid valve S1
ECM


P0976
(DI±646)Shift Solenoid ºBº Control Circuit
Low (Shift Solenoid Valve S2)Short in shift solenoid valve S2 circuit
Shift solenoid valve S2
ECM


P0977
(DI±646)Shift Solenoid ºBº Control Circuit
High (Shift Solenoid Valve S2)Open in shift solenoid valve S2 circuit
Shift solenoid valve S2
ECM


P0985
(DI±651)Shift Solenoid ºEº Control Circuit
Low (Shift Solenoid Valve SR)Short in shift solenoid valve SR circuit
Shift solenoid valve SR
ECM


P0986
(DI±651)Shift Solenoid ºEº Control Circuit
High (Shift Solenoid Valve SR)Open in shift solenoid valve SR circuit
Shift solenoid valve SR
ECM


P2714
(DI±656)Pressure Control Solenoid ºDº
Performance
(Shift Solenoid Valve SLT)Shift solenoid valve SLT remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P2716
(DI±662)Pressure Control Solenoid ºDº
Electrical
(Shift Solenoid Valve SLT)Open or short in shift solenoid valve SLT circuit
Shift solenoid valve SLT
ECM


P2740
(DI±666)Transmission Fluid Temperature
Sensor ºBº CircuitOpen or short in ATF temperature sensor No.2 circuit
Transmission wire (ATF temperature sensor No.2)
ECM


P2742
(DI±666)Transmission Fluid Temperature
Sensor ºBº Circuit Low InputShort in ATF temperature sensor No.2 circuit
Transmission wire (ATF temperature sensor No.2)
ECM


P2743
(DI±666)Transmission Fluid Temperature
Sensor ºBº Circuit High InputOpen in ATF temperature sensor No.2 circuit
Transmission wire (ATF temperature sensor No.2)
ECM


P2757
(DI±672)
Torque Converter Clutch Pres-
sure Control Solenoid Perfor-
mance
(Shift Solenoid Valve SLU)Shift solenoid valve SLU remains open or closed
Valve body is blocked
Torque converter clutch
Automatic transmission (clutch, brake or gear, etc.)
Line pressure is too low


P2759
(DI±680)
Torque Converter Clutch Pres-
sure Control Solenoid Control
Circuit Electrical
(Shift Solenoid Valve SLU)Open or short in shift solenoid valve SLU circuit
Shift solenoid valve SLU
ECM



D14162
Clutch Drum
(Timing Rotor)
Input Speed Sensor NT
(Transmission Revolution Sensor NT)Output Speed Sensor SP2
(Transmission Revolution Sensor SP2)
Parking Gear
(Timing Rotor)
D14148
GND
1 V/DIV
2 ms/DIV
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±591
785 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0717 Input Speed Sensor Circuit No Signal
CIRCUIT DESCRIPTION
This sensor detects the rotation speed of the turbine which shows the input revolution of transmission. By
comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM
detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure ac-
cording to various conditions, thus, providing smooth gear shift.
DTC No.DTC Detection ConditionTrouble Area
P0717
All conditions below are detected for 5 secs. or more
(1±trip detection logic)
(a) Gear change is not performed
(b) Gear position: 4th or 5th
(c) T/M input shaft rpm: 300 rpm or less
(d) T/M output shaft rpm: 1,000 rpm or more
(e) Park/neutral position switch:

NSW input signal is OFF

R input signal is OFF

L input signal is OFF
(f) Shift solenoid valves, park/neutral position switch and ve-
hicle speed sensor are in normal operation

Open or short in speed sensor (NT) circuit

Speed sensor (NT)

ECM

Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between terminals NT+ and NT± of
the ECM connector.
Standard: Refer to the illustration.
TerminalNT+ ± NT±
Tool setting1V/DIV, 2ms/DIV
Vehicle conditionEngine idle speed (P or N position)
DIDJ8±01

D14162
Clutch Drum
(Timing Rotor)
Input Speed Sensor NT
(Transmission Revolution Sensor NT)Output Speed Sensor SP2
(Transmission Revolution Sensor SP2)
Parking Gear
(Timing Rotor)
C13480D14149
GND
2 V/DIV
20 ms/DIV
DI±596
± DIAGNOSTICSAUTOMATIC TRANSMISSION
790 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0722 Output Speed Sensor Circuit No Signal
CIRCUIT DESCRIPTION
The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the
ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the
speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assy rotates, and this voltage
is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.
The gear shift point and lock±up timing are controlled by the ECM based on the signals from this vehicle
speed sensor and the throttle position sensor signal.
DTC No.DTC Detection ConditionTrouble Area
P0722
All conditions below are detected 500 times or more continu-
ously (1±trip detection logic)
(a) No signal from speed sensor (SP2) is input to ECM while 4
pulses of No. 1 vehicle speed sensor signal are sent
(b) Vehicle speed is 9 km/h (6 mph) or more for at least 4 sec.
(c) Park/neutral position switch is OFF.
(d) Transfer position is except neutral (4WD).

Open or short in speed sensor (SP2) circuit

Speed sensor (SP2)

ECM

Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between terminals SP2+ and SP2±
of the ECM connector.
Standard: Refer to the illustration.
TerminalSP2+ ± SP2±
Tool setting2V/DIV, 20ms/DIV
Vehicle conditionVehicle speed 20 km/h (12 mph)
DIDJ9±01