2001 TOYOTA SEQUOIA warning

H23040
LA A20
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1497
1691 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check combination meter.
PREPARATION:
Connect the negative (±) terminal cable to the battery, and wait for at least 2 seconds.
CHECK:
Turn the ignition switch to the ON position, check the operation of the SRS warning light.
OK:
The SRS warning light comes on (goes off 6 seconds after the ignition switch is turned to the
ON position).
NG Go to step 3.
OK
Replace airbag sensor assembly (see page RS±82).
3 Check wire harness (combination meter ± airbag sensor assembly).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) Disconnect the connector from the combination meter.
(d) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Measure the voltage according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A20±14 (LA) ±
Body groundIgnition switch ONBelow 1 V
NG Repair or replace wire harness.
OK
Replace combination meter (see page BO±89).

H24006
Airbag Sensor
Assembly
TC 15
P±B
A20 G Instrument Panel J/B Sub J/B No. 4
D6
DLC3 5
4D 5
4E
5
4B
5
4C5
4A P±B
P±B
P±B P±B 23
E4 ECM
TC
T5
Translate ECU
T17
Tire Pressure Monitor ECUTC
TC28
12 13TC
CG
4O
A
J43
J/C
IGA
O 9
1A 15
1F DI±1498
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1692 Author: Date:
2005 SEQUOIA (RM1146U)
TC Terminal Circuit
CIRCUIT DESCRIPTION
DTC output mode is set by connecting terminals TC and CG of the DLC3.
The DTCs are displayed by blinking of the SRS warning light.
WIRING DIAGRAM
HINT:
When each warning light stays blinking, a ground short in the wiring of the terminal TC of the DLC3 or an
internal ground short in each ECU is suspected.
DIDHW±01

DIDDZ±01
I28552
Position Control ECU
& Switch Assy
Park/Neutral
Position Switch
Combination
MeterPower Seat Motor
Driver Side (Reclining)
Power Seat Motor
Driver Side (Slide) Power Seat Motor
Driver Side (Front Vertical) Power Seat Motor
Driver Side (Lifter)
Front Door Courtesy
Light Switch Assy Seat Memory Switch Lumbar
Support
Control
MotorLumbar Support
Control Switch To Battery
To Battery To Ignition SwitchECU±B
PWR SEATECU±IGSYSB
IG
+BRCL+
RCL±
LFT+
LFT±
FRV+
FRV±
SLD+
SLD±
SW1
SW2
MMRYDCTY
Key Unlock
Warning Switch
KSW
Body ECU
BEANTo Ignition Switch
± DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)DI±1503
1697 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

DIDGG±01
± DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)DI±1511
1705 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the DATA LIST displayed on the hand±held tester, you can read the value of the switch, sensor, etc.
without parts removal. Reading the DATA LIST as the first step of troubleshooting is one way to shorten the
labor time.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) Read the DATA LIST according to the display on the tester.
D±SEAT:
ItemMeasurement Item/
Display (Range)Normal Condition
RECLIN SW REARReclining switch signal (Rearward)/
ON or OFFON: Reclining switch (Rearward) is ON
OFF: Reclining switch (Rearward) is OFF
RECLIN SW FRONTReclining switch signal (Forward)/
ON or OFFON: Reclining switch (Forward) is ON
OFF: Reclining switch (Forward) is OFF
F VTCL SW DOWNFront vertical switch signal (Downward)/
ON or OFFON: Front vertical switch (Downward) is ON
OFF: Front vertical switch (Downward) is OFF
F VTCL SW UPFront vertical switch signal (Upward)/
ON or OFFON: Front vertical switch (Upward) is ON
OFF: Front vertical switch (Upward) is OFF
LIFTER SW DOWNLifter switch signal (Downward)/
ON or OFFON: Lifter switch (Downward) is ON
OFF: Lifter switch (Downward) is OFF
LIFTER SW UPLifter switch signal (Upward)/
ON or OFFON: Lifter switch (Upward) is ON
OFF: Lifter switch (Upward) is OFF
SLIDE SW REARSliding switch signal (Rearward)/
ON or OFFON: Sliding switch (Rearward) is ON
OFF: Sliding switch (Rearward) is OFF
SLIDE SW FRONTSliding switch signal (Forward)/
ON or OFFON: Sliding switch (Forward) is ON
OFF: Sliding switch (Forward) is OFF
POWER VOLTAGEPower supply for position control ECU & switch/
MIN: 0 V, MAX: 19.89 VWithin range from 11 V to 14 V
IG SWIgnition switch status/
ON or OFFON Ignition switch is ON
OFF: Ignition switch is OFF
KEY UNLOCK SWKey unlock warning switch signal/
ON or OFFON: Key is in ignition key cylinder
OFF: Key is not in ignition key cylinder
D±DOOR WARN SWDoor courtesy switch signal/
ON or OFFON: Driver side door is open
OFF: Driver side door is closed
PNP SWPark/neutral position switch signal/
ON or OFFON: Shift lever in neutral position
OFF: Shift lever in any position except neutral
M2 SWSeat memory switch M2 signal/
ON or OFFON: Seat memory switch M2 is ON
OFF: Seat memory switch M2 is OFF
M1 SWSeat memory switch M1 signal/
ON or OFFON: Seat memory switch M1 is ON
OFF: Seat memory switch M1 is OFF
SET SWSeat memory set switch signal/
ON or OFFON: Memory set switch is ON
OFF: Memory set switch is OFF
SLIDE POSSeat sliding position/
MIN: ±4096, MAX: 4096Within range from ±4096 to 4096
RECLN POSSeatback position/
MIN: ±4096, MAX: 4096Within range from ±4096 to 4096
F VTCL POSSeat front vertical position/
MIN: ±4096 MAX: 4096Within range from ±4096 to 4096
LIFTER POSSeat lifter position/
MIN: ±4096 MAX: 4096Within range from ±4096 to 4096
MEM M1 SW
Driving position memorized with seat memory
switch M1/
MEM or NOT MEMMEM: Memorized
NOT MEM: Not memorized

I28464
ECM
Sub J/B No.4
23
E4
1328
T5
15
A205
4E
TC
TC5
4B
5
4C 5
4D
5
4A 15
1F 9
1A
J43
J/C12
T17 P±B P±B Translate ECU
TCP±B
P±B
O
O 4 TC
CG D6
DLC3 Airbag Sensor
Assembly
Instrument Panel J/BTire Pressure
ECU
P±B
G
A A
IGTC
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1567
1761 Author: Date:
2005 SEQUOIA (RM1146U)
Diagnosis circuit
CIRCUIT DESCRIPTION
Making a short circuit between terminals TC and CG of the DLC3 will output DTCs from the DLC3.
WIRING DIAGRAM
HINT:
When a particular warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an
internal ground short in the relevant ECU is suspected.
DIDF5±01

DI1AP±40
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±1573
1767 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
SymptomSuspected AreaSee page
Immobiliser is not set.
(Engine starts with key codes other than the registered key code.)1. Door courtesy light switch circuit (DTC12)
2. Transponder key ECUDI±1585
IN±35
Engine does not start.
1. Key
2. Key unlock warning switch circuit (DTC11)
3. Transponder key coil
4. Transponder key ECU
5. ECM*1
DI±1582
BE±143
IN±35
IN±35
Security indicator is always ON.
1. Security indicator
2. Security indicator light circuit
3. Transponder key ECU*2
DI±1597
IN±35
Security indicator is always ON.
(Although code has been registered in the automatic registration
mode, indicator is not OFF.)1. Transponder key coil
2. Transponder key ECUBE±143
IN±35
Security indicator is OFF.
(When DTC of immobiliser is output)1. Transponder key coil
2. Transponder key ECUBE±143
IN±35
Security indicator is OFF.
(When DTC of immobiliser is not output)1. Security indicator light circuit
2. Diagnosis circuit
3. Transponder key ECUDI±1597
DI±1599
IN±35
Security indicator is abnormally blinking.Transponder key ECUIN±35
No code is output.
1. Power source circuit
2. Diagnosis circuit
3. Transponder key ECUDI±1595
DI±1599
IN±35
*1 : Check that the key which did not start the engine has been registered, and that it is possible to start with
any other already registered key.
*2 : Finish the automatic registration mode because the mode might still be set.

DIABB±02
I24389
T16 Transponder Key ECU: DI±1574
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1768 Author: Date:
2005 SEQUOIA (RM1146U)
TERMINALS OF ECU
Symbols (Terminals No.)Wiring ColorConditionSpecified condition
+B e GND
(T16 ± 1 e T16 ± 14)W±R e OAlways10 to 14 V
IG e GND
(T16 ± 2 e T16 ± 14)B±O e OIgnition switch ON10 to 14 V
D e GNDWLOIgnition switch ON " 10 to 14 V " D e GND
(T16 ± 3 e T16 ± 14)W±L e OIgnition switch ON "
Connect terminals OP3 and CG of DLC310 to 14 V "
Below 2 V
CODE e GND
(T16 ± 4 e T16 ± 14)R±Y e OIgnition switch ON10 to 14 V
RXCK e GND
(T16 ± 5 e T16 ± 14)LG e OIgnition switch ON10 to 14 V
VC12 e AGND
(T16 ± 6 e T16 ± 12)GR±B e GR±LAlways10 to 14 V
IND e GNDLG BO
Security indicator light is on. (It flashes when the immobiliser
ti ti)3 to 6 V " IND e GND
(T16 ± 7 e T16 ± 14)LG±B e Osystem is operating.) "
Security indicator light is off.3 to 6 V "
Below 1 V
CTY e GNDGR LODriver's door closed " 10 to 14 V " CTY e GND
(T16 ± 8 e T16 ± 14)GR±L e ODriver s door closed "
Driver's door open10 to 14 V "
Below 1 V
KSW e GNDYGOKey unlock warning switch ON (Key inserted) " Below 1 V " KSW e GND
(T16 ± 9 e T16 ± 14)Y±G e OKey unlock warning switch ON (Key inserted) "
Key unlock warning switch OFF (Key not inserted)Below 1 V "
10 to 14 V
EFII e GND
(T16 ±10 e T16 ± 14)L±Y e OIgnition switch ON10 to 14 V
EFIO e GND
(T16 ±11 e T16 ± 14)P±G e OIgnition switch ON10 to 14 V
AGND e Body ground
(T16 ±12 e Body
ground)
GR±L e Body groundAlwaysBelow 1 V
TXCT e GND
(T16 ± 13 e T16 ± 14)Y±G e OIgnition switch ON10 to 14 V
GND e Body ground
(T16 ±14 e Body
ground)
O e Body groundAlwaysBelow 1 V

DI1AM±35
DI±1578
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1772 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
ECM DIAGNOSTIC TROUBLE CODE CHART (MIL)
DTC No.
(See page)Detection ItemTrouble Area
99
(DI±1580)Engine immobiliser system malfunction

Transponder key ECU

ECM

Wire harness
TRANSPONDER KEY ECU DIAGNOSTIC TROUBLE CODE CHART (SECURITY INDICATOR LIGHT)
DTC No.
(See page)Detection ItemTrouble Area
11
(DI±1582)Code 11 is not output

Unlock warning switch

Transponder key ECU

Wire harness
12
(DI±1585)Code 12 is not output

Driver door courtesy lamp switch

Transponder key ECU

Body ECU

Wire harness
13
(DI±1587)Code 13 is not output

Ignition switch

Transponder key ECU

Wire harness
21, 22
(DI±1589)Code 21 or 22 is not output

Key

Transponder key ECU

Transponder key amplifier with key coil

Wire harness
31, 35, 36, 37
(DI±1592)Code 31, 35, 36 or 37 is outputKey
32, 33
(DI±1593)Code 32 or 33 is output

Key

Transponder key ECU

Wire harness
34Code 34 is outputTransponder key ECU has no memory space to register anoth-
er key code
HINT:

DTCs 11, 12, 13, 21 and 22 are normal codes.

As for the normal codes, if the corresponding DTC is not output while operating any of the components
listed under ºTrouble Areaº, perform the inspection described in the reference pages.

DTCs 31, 32, 33, 34, 35, 36, 37 and 99 are abnormal codes.