Page 3733 of 4770
B00319
Recommended Viscosity (SAE):
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE10W±30
5W±30 PREFERRED°C °F
±20
±290
±1820
±740
460
1680
27100
38
LU0FR±01
P25173SST
P25171
Oil Pressure Gauge
± LUBRICATION (1MZ±FE)OIL AND FILTER
LU±1
1665 Author: Date:
OIL AND FILTER
INSPECTION
1. CHECK ENGINE OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If the quality is visibly poor, replace the oil.
Oil grade:
API grade SJ, Energy±Conserving or ILSAC multi-
grade engine oil.
SAE 5W ± 30 is the best choice for your vehicle, for
good fuel economy, and good starting in cold weath-
er.
2. CHECK ENGINE OIL LEVEL
After warm up the engine and then 5 minutes after the engine
stop, oil level should be between the low level and full level
marks on the dipstick.
If low, check for leakage and add oil up to the full level mark.
NOTICE:
Do not fill with engine oil above the full level mark.
3. REMOVE OIL PRESSURE SWITCH, AND INSTALL
OIL PRESSURE GAUGE
(a) Using SST, remove the oil pressure switch.
SST 09816±30010
(b) Install the oil pressure gauge.
4. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
5. CHECK OIL PRESSURE
Oil pressure:
At idle29 kPa (0.3 kgf/cm2, 4.3 psi) or more
At 3,000 rpm294 ± 539 kPa (3.0 ± 5.5 kgf/cm2, 43 ± 78 psi)
Page 3751 of 4770
MA001±10
± MAINTENANCEOUTSIDE VEHICLE
MA±1
44 Author: Date:
OUTSIDE VEHICLE
GENERAL MAINTENANCE
These are maintenance and inspection items which are considered to be the owner's responsibility.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item an cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge. If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing nuts. If necessary, tighten them.
4. TIRE ROTATION
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean. If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, have the cause found and corrected.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.
Page 4027 of 4770
SS06M±01
± SERVICE SPECIFICATIONSSTEERING
SS±65
228 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
STEERING COLUMN
Steering wheel pad set screw (Torx screw)7.17263 in.´lbf
Steering wheel set nut3536026
Intermediate shaft assembly x Control valve shaft3536026
Steering column assembly x Intermediate shaft assembly3536026
Steering column assembly set nut2526019
Turn signal bracket x Column tube77061 in.´lbf
Lower column tube attachment x Column tube1919514
PS VANE PUMP
5S±FE and 1MZ±FE Engines:
Pressure feed tube x Control valve housing 5S±FE Engine32 (25)326 (250)24 (18)
Pressure feed tube x Pressure feed tube 1MZ±FE Engine20 (25)203 (250)15 (18)
Clamp plate set nut 5S±FE Engine101007
Clamp plate set nut 1MZ±FE Engine7.88069 in.´lbf
PS vane pump set bolt A bolt29 (43)293 (440)21 (32)
PS vane pump set bolt B bolt4344032
Oil pressure switch x Union bolt2121015
Union bolt x Pressure feed tube5252538
Vane pump pulley set nut4344032
Front bracket x Rear bracket4344032
Suction port union set bolt131309
Pressure port union8385062
Rear housing set bolt2424017
PS GEAR
Pressure feed tube clamp plate set nut101007
Pressure feed and return tubes x Control valve housing32 (25)326 (250)24 (18)
Stabilizer bar set bolt1919514
PS gear assembly set bolt and nut1811,850134
Turn pressure tube union nut10 (13)102 (130)7 (9)
Tie rod end lock nut7475054
Rack x Rack end60 (83)615 (850)45 (62)
Rack guide spring cap lock nut50 (69)513 (700)37 (51)
Rack housing cap5960043
Selt±locking nut2525018
Control valve housing set bolt1818513
( ): For use without SST
Page 4310 of 4770
W03349
Pressure Port Union
Oil Ring
Flow Control Valve
Suction Port Union
Spring
O±Ring
Front Housing Gasket Rear Housing
Rear Bracket
Rear Housing
O±Ring
Rear Bracket
Wave Washer
Cam Ring Straight Pin
Vane Plate Rotor
Side Plate Vane Pump
x10
O±Ring
Snap Ring
N´m (kgf´cm, ft´lbf)
Non±reusable part
Power steering fluid: Specified torque Vane Pump Shaft
Vane Pump PulleyFront Bracket Front Bracket
5S±FE Engine :
TOYOTA KOUKI Made :24 (240, 17)
43 (440, 32)
24 (240, 17)
83 (850, 62)
13 (130, 9)
5S±FE Engine :5S±FE Engine :
1MZ±FE Engine :1MZ±FE Engine :
43 (440, 32)
43 (440, 32) SR±20
± STEERINGPOWER STEERING VANE PUMP
2115 Author: Date:
