2000 TOYOTA CAMRY engine oil

(c) Subtract the lifter diameter measurement from the
lifter bore diameter measurement.
Standard oil clearance:
0.024 ± 0.052 mm (0.0009 ± 0.0020 in.)
Maximum oil clearance:
0.07 mm (0.0028 In.)
If the oil clearance is greater than maximum, replace
the lifter. If necessary, replace the cylinder head.
12. INSPECT MANIFOLDS
Using a precision straight edge and feeler gauge, mea±
sure the surface contacting the cylinder head for war±
page.
Maximum warpage:
0.30 mm (0.0 118 In.)
If warpage is greater than maximum, replace the man±
ifold. 11. INSPECT VALVE LIFTERS AND LIFTER BORES
(a) Using a caliper gauge, measure the lifter bore diame±
ter of the cylinder head.
Lifter bore diameter:
31.000 ± 31.018 mm (1.2205 ± 1.2213 In.)
(b) Using a micrometer, measure the lifter diameter.
Lifter diameter:
30.966 ± 30.976 mm (1.2191 ± 1.2195 in.)
± 5S±FE ENGINEENGINE MECHANICALEG1±65

CYLINDER HEAD ASSEMBLY
(See Components for Removal and Installation)
HINT:
wThoroughly clean all parts to be assembled.
Before installing the parts, apply new engine oil to all
sliding and rotating surfaces.
wReplace all gaskets and oil seals with new ones.
(c) Using SST, compress the valve spring and place the 2
keepers around the valve stem.
SST 09202 ± 70010(b) Install the following parts:
(1) Valve
(2) Spring seat
(3) Valve spring
(4) Spring retainer 1. INSTALL VALVES
(a) Using SST, push in a new oil seal.
SST 09201 ±41020
HINT: The intake valve oil seal is brown and the
exhaust valve oil seal is black.
± 5S±FE ENGINEENGINE MECHANICALEG1±66

CYLINDER HEAD INSTALLATION
(See Components for Removal and Installation)
1. INSTALL CYLINDER HEAD
A. Place cylinder head on cylinder block
(a) Place a new cylinder head gasket in position on the
cylinder block.
NOTICE: Be careful of the installation direction.
(b) Place the cylinder head in position on the cylinder
head gasket.
B. Install cylinder head bolts
HINT:
wThe cylinder head bolts are tightened in 2 progressive
steps (steps (b) and (d)).
wIf any cylinder head bolt is broken or deformed, re±
place it.
(a) Apply a light coat of engine oil on the threads and
under the heads of the cylinder head bolts.
(b) Using SST, install and uniformly tighten the 10 cylin±
der head bolts and plate washers in several passes, in
the sequence shown.
SST 09011± 38121
Torque: 49 N±m (500 kgf±cm, 36 ft±lbf)
If any one of the cylinder head bolts does not meet the
torque specification, replace the cylinder head bolt.2. INSTALL VALVE LIFTERS AND SHIMS
(a) Install the valve lifter and shim.
(b) Check that the valve lifter rotates smoothly by hand. (d) Using a plastic±faced hammer, lightly tap the valve
stem tip to assure proper fit.
± 5S±FE ENGINEENGINE MECHANICALEG1±67

2. INSTALL SPARK PLUG TUBES
(a) Clean the cylinder head tube holes of any residua!
adhesive, oil or foreign particles. Remove any oil with
kerosene or gasoline.
(b) Screw the threads of the spark plug tube coated with
adhesive into the cylinder head.
(c) Using the spark plug tube nut and a 30 mm socket
wrench, tighten the spark plug tubes.
Torque: 39 N±m (400 kgf±cm, 29 ft±lbf)
(b) Install the following parts:
(1) Camshaft gear spring
(2) Camshaft sub gear
(3) Wave washer
HINT: Align the pins on the gears with the spring ends.(d) Retighten the cylinder head bolts 90
in the sequence
shown on the previous page.
(e) Check that the painted mark is now at a 90
angle to
front.
3. ASSEMBLY EXHAUST CAMSHAFT
(a) Mount the hexagon wrench head portion of the cam±
shaft in a vise.
NOTICE: Be careful not to damage the camshaft.
(c) Mark the front of the cylinder head bolt head with
paint.
± 5S±FE ENGINEENGINE MECHANICALEG1±68

B. Install exhaust camshaft
(a) Set the knock pin of the intake camshaft at 10±455
BTDC of camshaft angle.
HINT: The above angle allows the No.2 and No.4
cylinder cam lobes of the exhaust camshaft to push
their valve lifters evenly.(e) Apply a light coat of engine oil on the threads and
under the heads of the bearing cap bolts.
(f) Install and uniformly tighten the 10 bearing cap bolts
in several passes, in the sequence shown.
Torque: 19 N±m (190 kgf±cm, 14 ft±lbf)
(h) Using SST, tap in the oil seal.
SST 09223±4601 1 (d) Install the bearing caps in their proper locations.
(g) Apply MP grease to a new oil seal lip.
± 5S±FE ENGINEENGINE MECHANICALEG1±70

(b) Apply MP grease to the thrust portion of the cam±
shaft.
(c) Engage the exhaust camshaft gear to the intake cam±
shaft gear by matching the timing marks on each gear.
(d) Roll down the exhaust camshaft onto the bearing
journals while engaging gears with each other.
NOTICE: There are also assembly reference marks on
each gear as shown in the Illustration. Do not use these
marks.
5. CHECK AND ADJUST VALVE CLEARANCE
(See page EG1±12)
Turn the camshaft and position the cam lobe upward,
and check and adjust the valve clearance.
Valve clearance (Cold):
Intake
0.19 ± 0.29 mm (0.007 ± 0.011 In.)
Exhaust
0.28 ± 0.38 mm (0.011 ± 0.015 In.)(e) Turn the intake camshaft clockwise or counterclockwise little
by little until the exhaust camshaft sits in
the bearing journals evenly without rocking the cam±
shaft on the bearing journals.
NOTICE: It is very important to replace the camshaft in
the bearing journals evenly while tightening bearing caps
in the subsequent steps.
(f) Install the bearing caps in their proper locations.
(g) Apply a light coat of engine oil on the threads and
under the heads of the bearing cap bolts.
(h) Install and uniformly tighten the 10 bearing cap bolts
in several passes, in the sequence shown.
Torque: 19 N±m (190 kgf±cm, 14 ft±lbf)
(i) Remove the service bolt (B).
± 5S±FE ENGINEENGINE MECHANICALEG1±71

10. INSTALL GENERATOR BRACKET
Install the generator bracket with the 3 bolts.
Torque: 42 N±m (425 kgf±cm, 31 ft±lbf)
11. INSTALL ENGINE HANGERS
Install the engine hanger with the bolt. Install the 2
engine hangers. Install the ground strap.
Torque: 25 N±m (250 kgf±cm, 18 ft±lbf)
(c) Install the gasket to the head cover.
(d) Install the head cover with the 4 grommets and nuts.
Uniformly tighten the nuts in several passes.
Torque: 23 N±m (230 kgf±cm, 17 ft±lbf)
HINT: Install the grommets so that their markings are
as shown in the illustration.
9. INSTALL OIL PRESSURE SWITCH
Apply adhesive to 2 or 3 threads.
Adhesive:
Part No.08833±00080, THREE BOND 1324 or equivalent
12. INSTALL NO.3 TIMING BELT COVER
Install the timing belt cover with the 4 bolts.
Torque: 7.8 N±m (80 kgf±cm, 69 in±lbf)
± 5S±FE ENGINEENGINE MECHANICALEG1±73

(b) Connect the following hoses:
(1) Upper radiator hose
(2) Water bypass pipe hose
(3) Heater water hose
(4) IAC water bypass hose
(5) TVV (for EVAP) vacuum hose (from P port of
throttle body)
(6) TVV (for EVAP) vacuum hose (from charcoal canister) 27. INSTALL WATER BYPASS PIPE
(a) Install a new 0±ring to the bypass pipe.
(b) Apply soapy water on the 0± ring.
(c) Install a new gasket and the bypass pipe with the 2
nuts and 2 bolts.
Torque (Nut): 8.8 N±m (90 kgf±cm. 78 in.±lbf)
28. INSTALL WATER OUTLET
(a) Install a new gasket and the water outlet with the 2
bolts.
Torque: 15 N±m (150 kgf±cm, 11 ft±lbf)
(d) Connect the following hoses:
(1) IAC water bypass hose
(2) Heater water hose
(3) w/ Oil Cooler:
2 oil cooler water bypass hoses (f) Connect the IAC valve connector.
(g) Connect the throttle position sensor connector.
± 5S±FE ENGINEENGINE MECHANICALEG1±79