2000 TOYOTA CAMRY turn signal bulb

13
EXTERIOR
EXTERIOR EQUIPMENT
 BUMPER
The Super Olefin Polymer, a material that is light, scratch resistant and highly recyclable, has been adopted in the
front bumper.
Urethane bumper has been adopted for the rear bumper for weight reduction.

 LIGHTS
1. Front Lights
The headlight, parking light, and turn signal light
have been concentrated to improve the visibility
from other vehicles, while also reducing weight.
The headlight uses HB2 (H4) type bulb to provide
excellent night±time visibility.
A light auto turn±off system is standard
equipment for all models.
The daytime running light system is standard
equipment on models for Canada.

'99camry U
80
The daytime running light control sensor
is on the top of the passenger 's side
instrument panel.
Do not place anything on the instrument
panel, and/or do not affix anything on the
windshield to block this sensor.High±Low beamsÐFor high beams, turn
the headlights on and push the lever away
from you (position 1). Pull the lever to-
ward you (position 2) for low beams.
The headlight high beam indicator light
(blue light) on the instrument panel will
tell you that the high beams are on.
Flashing the high beam headlights
(position 3)ÐPull the lever all the way
back. The high beam headlights turn off
when you release the lever.
You can flash the high beam headlights
with the knob turned to ºOFFº.TURN SIGNALS
To signal a turn, push the headlight/
turn signal lever up or down to position
1.
The key must be in the ºONº position.
The lever automatically returns after you
make a turn, but you may have to return
it by hand after you change lanes.
To signal a lane change, move the lever
up or down to the pressure point (position
2) and hold it.
If the turn signal indicator lights (green
lights) on the instrument panel flash faster
than normal, a front or rear turn signal
bulb is burned out.

'99camry U
231
Replacing light bulbsÐ
The following illustrations show how to
gain access to the bulbs. When replacing
a bulb, make sure the ignition switch and
light switch are off. Use bulbs with the
wattage ratings given in the table.
CAUTION
Halogen bulbs have pressurized gas
inside and require special handling.
They can burst or shatter if scratched
or dropped. Hold a bulb only by its
plastic or metal case. Do not touch
the glass part of a bulb with bare
hands.
NOTICE
Only use a bulb of the listed type.
Light bulbsBulb
No.WTy p e
HeadlightsHB260/55A
Parking, front side
marker and front
turn signal lights
Ð27/8B
Rear side marker
lights1943.8C
Rear turn signal
lights315627C
Stop and tail lights315727/8C
Tail light9049.3C
Back±up lights92118C
License plate lightsÐ5C
High mounted
stoplight21CP18C
Personal lightÐ10B
Interior lightÐ10D
Vanity lightsÐ3D
Glove box lightÐ1.2C
Trunk lightÐ3.8C
A: HB2 halogen bulbs
B: Single end bulbs
C: Wedge base bulbs
D: Double end bulbs

J
5
678
25 CAMRY (
Cont' d)
11
B
7
C
13
C
6
B
3
B
5
C
2
A
1
A R
R±L
Y±R
G±W
BR
BR
IJ13
IJ16
IJ12
IJ178
C
6
C
15
B Y±G
P
LR
R±L
Y± R
G±W
BR
BR
Y±G
B±O
P
L
4
A4
C2
C 11
C2
B4
B3
A7
B
IG317
IK23
2 1
EBLeft radiat or
side support IGInstrument
panel br ace
LH 2 1IG23
IG16
7IG16
A
11
A
7
A
8
A 10
A
9
A
9
C
5
A
3
C
10
B
12
A
13
B 12
B 10
C9
B8
B5
B 16
B 13
A1
C1
B 14
B 12
C L
2
D
N
R
P
SLI P
TRAC OFF
DOOR
O/D OFF See Illuminat ion
System< 10±4>
A
R±W R± W
W± B R±WW± B
R±W
R±W R±W
B±O
P± L P±L P± LB±O(
*4) R± W (
*6)
(
*7)J 2
JUNCTI ON
CONNE CT OR
Fro m Da yti me
Running Light
Re la y(
Main)
< 7±2>
B
BB
(
*6)
J11
JUNCTION
CONNECTOR
B 2
BRAKE FLUID LEVEL
WARNING SWP 3
PARKING BRAKE SW W 1
WASHER L EVEL
WARNING SW
From Day time Running
Light Relay(
Main)
< 7±2>
Fr om Park /Neutral
Pos it ion SW(
A/T)
or
Clutch Start SW(
M/T)
<1±2>GR(
*3)
See Key Reminder and Seat Belt
Warning System< 21±3> See ABS(
TMC Made)
System< 19±2>
See ABS(
TMMK Made)
System< 20±2>
See ABS and Tr act ion
Control System< 18±1>See Engine Cont rol and
Immobiliser System< 2±3> < 3±2>See Charging
System< 1±4> See Taillight
System< 11±4>
SRS CRUISE HIGH BEAMOIL
SEAT BELTABS MA LF UNCT I ON I NDI CA TOR
LAMPWASHER LEVELBULB
CHE CK
RE L AY REAR LIGHTSBRAKE
CHARGETURN RHTURN LH ILLUMINATION
TRIP METER
ODOMETER
(
*5) TACHOMETERWATER
TEMP. FUEL
FUEL
SECURI TYSee Electronically Controlled
Transmission and A/T
Indicator System
<4±4><5±4>
See ABS and
Tr act ion Contr ol
Sy st em< 18±1>
See Tur n Signal and
Hazard Warning Light
Sy st em< 8±2> < 8±3>
See Headlight
Sy st em< 6±3> < 7±3>
Se e SRS Sy st e m
< 28±4> See Theft Deterrent
System< 15±3>
See Interior Light
System< 9±4>
See Electronically Controlled
Transmiss ion and A/T Indicator
System< 4±3> < 5±3>
See Illumination Sy st em
< 10±4>
IG33
V± W V± W
V±W V±WB B
B J15
JUNCTION
CONNE CT ORFrom Cruise Control
ECU< 17±4> From Engine Contr ol
Module
< 2±7> < 3±9> < 4±3> < 5±3>
IJ15
1
See Cruise Control
System< 17±2> Y±B Y±B
IF Left kick
panel
O 1
OIL PRESSURE SWJ 5
JUNCTI ON
CONNE CTOR
W± B W± B
A A See Char ging Sys tem
< 1±4> A
B
C
D
E
F
G
H
I* 4 : TMMK Made, TMC Made USA w/ Traction Control
* 5 : Speedometer * 3 : Except * 4
W± B IG36
1
Combination M eter
B±O From Engine
Control Module
< 2±12> < 3±9>
C 8 C 9,
COMBINATION METERABC10, C* 6 : w/ Daytime Running Light
* 7 : w/o Day time Running Light
Fr om A/C Contr ol
Assembly< 29±5>V±W

BE±4
± BODY ELECTRICALBODY ELECTRICAL SYSTEM
2224 Author: Date:
Taillight does not light.
(Headlight does not light)1. Integration Relay (I/P J/B No.1)
2. Light Control Switch
3. Wire HarnessBE±14
BE±24
±
Taillight does not light.
(Headlight is normal)
1. TAIL Fuse (I/P J/B No.1)
2. Taillight Control Relay (I/P J/B No.1)
3. Integration Relay (I/P J/B No.1)
4. Light Control Switch
5. Wire Harness±
BE±24
BE±14
BE±24
±
Only one side light does not light.1. Bulb
2. Wire Harness±
±
Rear Combination light does not light.
1. Bulb
2. Light Failure Sensor
3. Wire Harness±
BE±37
±
ºAuto Turn±off Systemº does not operate.
1. GAUGE Fuse (I/P J/B No.1)
2. Integration Relay (I/P J/B No.1)
3. Door Courtesy Switch (Driver's)
4. Wire Harness±
BE±14
BE±24
±
*Terminal L of generator and parking brake switch
TURN SIGNAL AND HAZARD WARNING SYSTEM
SymptomSuspect AreaSee page
ºHazardº and ºTurnº do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher
3. Wire HarnessBE±30
BE±30
±
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Switch
3. Wire Harness±
BE±30
±
Hazard warning light does not light up.
(Turn is normal.)1. HORN Fuse (E/G Room J/B No.2)
2. Wire Harness±
±
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE±30
±
*1Turn signal does not light up.
1. Ignition Switch
2. TURN Fuse (I/P J/B No.1)
3. Turn Signal Switch
4. Wire HarnessBE±14
±
BE±30
±
*2Turn signal does not light up.
1. TURN Fuse (I/P J/B No.1)
2. Turn Signal Switch
3. Wire Harness±
BE±30
±
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE±30
±
Only one bulb does not light up.1. Bulb
2. Wire Harness±
±
*1: Combination meter, wiper and washer do not operate.
*
2: Combination meter, wiper and washer are normal.
INTERIOR LIGHT SYSTEM
SymptomSuspect AreaSee page
ºIlluminated Entry Systemº does not operate.
1. Door Courtesy Switch
2. Integration Relay (I/P J/B No.1)
3. Wire HarnessBE±32
BE±14
±
Only one interior light does not light up.1. Bulb
2. Wire Harness±
±
Interior light does not light up (All).1. DOME Fuse (E/G Room J/B No.2)
2. Wire Harness±
±

± BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE±7
2227 Author: Date:
Seat Belt warning light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Integration Relay (I/P J/B No.1)
4. Wire Harness±
BE±47
BE±47
±
Discharge warning light does not light up.
1. IGN Fuse (I/P J/B No.1)
2. Bulb
3. Wire Harness
4. Generator (5S±FE)
(1MZ±FE)±
±
±
CH±1
CH±1
Light Failure warning light does not light up.
1. Bulb
2. Light Failure Sensor
3. Bulb Check Relay
4. Wire Harness
5. Taillight system±
BE±37
BE±47
±
BE±24
Brake warning light does not light up.
1. Bulb
2. Parking Brake Switch
3. Brake Fluid Level Warning Switch
4. Bulb Check Relay
5. Meter Circuit Plate
6. Wire Harness±
BE±47
BE±47
BE±47
BE±46
±
SRS Warning light does not light up.
1. ECU±B Fuse (E/G Room J/B No.2)
2. Bulb
3. Airbag Sensor Assembly
4. Meter Circuit Plate
5. Wire Harness±
±
DI±626
BE±46
±
Open Door warning light does not light up.
1. DOME Fuse (E/G Room J/B No.2)
2. Bulb
3. Door Courtesy Switch
4. Meter Circuit Plate
5. Wire Harness±
±
BE±32
BE±46
±
Washer Level warning light does not light up.
1. Bulb
2. Washer Fluid Level Warning Switch
3. Meter Circuit Plate
4. Wire Harness±
BE±47
BE±46
±
COMBINATION METER
INDICATOR LIGHTS:
SymptomSuspect AreaSee page
O/D OFF indicator light does not light up.
1. Bulb
2. O/D OFF Switch (A140E)
(A541E)
3. Meter Circuit Plate
4. Wire Harness±
DI±431
DI±487
BE±46
±
Cruise Control indicator light does not light up.
1. Bulb
2. Cruise Control ECU
3. Meter Circuit Plate
4. Wire Harness±
IN±31
BE±46
±
High beam indicator light does not light up.
1. Bulb
2. Meter Circuit Plate
3. Wire Harness
4. Headlight System±
BE±46
±
BE±22
Turn indicator light does not light up.
1. Bulb
2. Meter Circuit Plate
3. Wire Harness
4. Turn Signal and Hazard Warning System±
BE±46
±
BE±29

BE0A9±02
N20150
Right
Left
2 31
BE1843
1 23
Turn Signal Light Bulbs (21 W)
N20140
1 2 3
4
5 6 7 8 9 10
BE±30
± BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
2250 Author: Date:
INSPECTION
1. INSPECT TURN SIGNAL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Left turn1 ± 2Continuity
Neutral±No continuity
Right turn2 ± 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (±) lead to terminal 3.
(b) Connect the 2 turn signal light bulbs in parallel to each
other to terminals 1 and 3, check that the bulbs flash.
HINT:
The turn signal lights should flash 60 to 120 times per minute.
If one of the front or rear turn signal lights has an open circuit,
the number of flashes will be more than 140 per minute.
If operation is not as specified, replace the flasher.
3. INSPECT HAZARD WARNING SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Switch OFF7 ± 10Continuity
Switch ON5 ± 6 ± 9
7 ± 8Continuity
Illumination circuit2 ± 3Continuity
If continuity is not as specified, replace the switch.

BE0AJ±03
Z18937
Connector ºAº Connector ºBº Connector ºCº
Connector ºAº
Connector ºBº
Connector ºCº
J±13±1±A J±16±1 J±13±1
1 2 3 4 5 6 7 8 9 10 11 12 1314 15 16 1 234 56 78 910111213 1 23456 78910111213
C7
C5
A2 B3
A1
C8
B15
C6
B6
A4
C4
B5
C10 B14
A13
B2
C1
B1
C9
A6
A11
A7
A10
A8
A9
C13
B8
B11
B12A5
C11
B4
B16 C2
A12
A3
B7
C3
C12
B9
B10
B13 F
E
T
S
ODOMETER
Fuel Level Warning
Seat Belt Warning
ABS Warning
Low Oil Pressure Warning
Cruise Control Indicator
Malfunction Indicator
O/D OFF Indicator
Light Failure Warning
Brake Warning
SLIP Indicator
TRAC Indicator
Washer Level Warning
Discharge Warning
Right Turn Indicator
Left Turn Indicator
Security Indicator
L
2
D
N
R
P
Illumination
Hi±Beam Indicator
Open Door Warning
SRS Warning
: Fuel Gauge
: Engine Coolant Temperature Gauge
: Tachometer
: Speedometer
No.
A
B
C1
2
3
4
5
6
7 8
9
10
11
12 13
14
15
16
2 3
4
5
6
7 8
9
10
11 12
131
2
3
4 5
6
7
8
9
10
11
12
13
F
E
T
SEngine coolant temperature sender gauge
Ground
Light failure sensor
Integration relay
Traction ECU
Park/neutral position switch (A/T)
O/D OFF switch (A/T)
IGN fuse
Turn signal switch
ST relay
Fuel sender gauge
Generator
Oil pressure switch
Fuel sender gauge
Parking brake switch and brake fluid level warning switch
Headlight dimmer switch
Headlight dimmer switch
Door courtesy switch
DOME fuse
ECU±B fuse
Airbag sensor assembly
ECM
No.1 Vehicle speed sensor Ground
Turn signal switch ECM
Traction ECU
ABS ECU
Ground No.1 Vehicle speed sensor
GAUGE fuse
Igniter
Security ECU
Cruise control ECU
Washer fluid level warning switch
Light control rheostat
TAIL fuse Park/neutral position switch (A/T) Park/neutral position switch (A/T) Park/neutral position switch (A/T) Park/neutral position switch (A/T)
Park/neutral position switch (A/T)Wire Harness Side
Bulb Check
Relay
N20107 N201081
BE±46
± BODY ELECTRICALCOMBINATION METER
2266 Author: Date:
CIRCUIT