Page 4657 of 4770
SUSPENSION BALL JOINT INSPECTION ± PG027-02December 4, 2002
Page 5 of 8
MODELLOCATION
LOWER BALL JOINT OR SUSPENSION
BALL JOINTUPPER BALL JOINT
MODELLOCATIONINSP.
METHODMAX. PLAYTURNING
TORQUEINSP.
METHODMAX. PLAYTURNING
TORQUE
Tacoma*3
(RZN140,
150, VZN150)
1995 ± 2003Front1±(A)0.5 mm
40 in. lbf
(4.5 N m)
or Less
2±(A)No Play
Felt40 in. lbf
(4.5 N m)
or Less
Tacoma*4
(RZN140,
150, VZN150)
1995 ± 2003Front1±(A)0.5 mm
31 in. lbf
(3.5 N m)
or Less
2±(A)No Play
Felt40 in. lbf
(4.5 N m)
or Less
Tacoma
(RZN161,
171, 19#,
VZN160, 170,
195)
1995 ± 2003
Front1±(A)0.5 mm
22 in. lbf
(2.5 N m)
or Less
2±(A)No Play
Felt40 in. lbf
(4.5 N m)
or Less
Truck*5
(RN8#, 90
VZN85, 9#)
1989 ± 1995Front1±(B)2.3 mm
44 in. lbf
(5.0 N m)
or Less
2±(A)2.3 mm
35 in. lbf
(4.0 N m)
or Less
Truck*6
(RN8#, 90
VZN85, 9#)
1989 ± 1995Front1±(B)0.5 mm
44 in. lbf
(5.0 N m)
or Less
2±(A)2.3 mm
35 in. lbf
(4.0 N m)
or Less
Truck
(RN10#, 11#
VZN10#, 110)
1989 ± 1995
Front1±(C)2.3 mm
53 in. lbf
(6.0 N m)
or Less
2±(B)2.3 mmTurns
Smoothly
T±100
(RCK10,
VCK1#)
1993 ± 1998
Front1±(A)0.5 mm
62 in. lbf
(7.0 N m)
or Less
2±(A)1.9 mm
35 in. lbf
(4.0 N m)
or Less
T±100
(VCK2#)
1993 ± 1998
Front1±(C)2.3 mm
53 in. lbf
(6.0 N m)
or Less
2±(B)
No Play
Felt (from
1995 MY)Turns
Smoothly
*1 Lower Ball Joint
*2 Suspension Arm Ball Joint
*3 With Serial Number Prior to Z718190
*4 With Serial Number After and including Z718190
*5 With Serial Number Prior to those listed in *6
*6 RN80±0087125, RN80±5130170, RN85±0004477, RN85±5046258, RN85±9010725, RN90±0014600,
RN90±5047105, RN90±9002376, VZN85±0003605, VZN85±5004547, VZN90±5025989, VZN95±0025290,
VZN90±0006119
Inspection
Information
(Continued)
Page 4660 of 4770
SUSPENSION BALL JOINT INSPECTION ± PG027-02December 4, 2002
Page 8 of 8
Inspect Ball Joint Turning Torque
Move the stud back and forth 5 times,
and then turn the stud continuously at
3±5 seconds per turn, and measure the
turning torque at the 5th turn.
HINT:
Refer to the table for standard values
for the turning torque. Turning
Torque
Inspection
Page 4692 of 4770
Toyota Supports ASE CertificationPage 1 of 2
ST001-01Title:
STEERING WHEEL NUT SERVICE
SPECIFICATION
Models:
All Applicable Models
Technical Service
BULLETIN
February 16, 2001
To make the steering wheel installation procedure similar for all models, the steering
wheel nut tightening torque has been standardized.
MODELMODEL YEARS
TERCELEL42, 531991 ± 1998
ECHONCP122000
PASEOEL44, 541992 ± 1997
COROLLAAE10#, ZZE1101993 ± 2001
CELICAAT180, ST18#, AT2#,
ST2#, ZZT23#1990 ± 2000
MR2SW2#, ZZW301991 ± 1995; 2000
CAMRYSXV10, 20, MCV10, 201992 ± 2000
CAMRY CNGSXV232000 ± 2001
CAMRY SOLARASXV20, MCV201999 ± 2000
AVALONMCX10, 201995 ± 2000
SUPRAJZA801993 1/2 ± 1998
RAV4SXA1#1996 ± 2000
RAV4 EVBEA111998 ± 2000
PREVIATRC10, 201991 ± 1997
SIENNAMCL101998 ± 2000
HIGHLANDERACU20, 25, MCU20, 252001
4RUNNERRN12#, 13#, VZN12#, 13#,
18#, RZN180, 1851990 ± 2000
LAND CRUISERFZ80, FZJ80, UZJ1001991 ± 2000
TRUCKRN8#, 9#, 10#, 110,
VZN85, 9#, 10#, 1101989 ± 1995
TACOMARZN140, 150, 161, 171,
19#, VZN150, 160, 170, 1951995 1/2 ± 2000
T100VCK10, 201993 ± 1998
TUNDRAVCK30, 40, UCK30, 402000
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
STEERING
Introduction
Applicable
Vehicles
Warranty
Information
Page 4695 of 4770
Page 1 of 1Toyota Supports ASE Certification
ST002±00Title:
STEERING WHEEL NUT
Models:
'94 ± '00 Camry
Technical Service
BULLETIN
May 12, 2000
The steering wheel installation nut torque specification has been changed. Please update
the repair manuals for the applicable vehicles.
1994 ± 2000 model year Camry
50 N m (510 kgf cm, 37 ft lbf)
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
STEERING
Introduction
Applicable
Vehicles
Warranty
Information
Page 4699 of 4770
Toyota Supports ASE CertificationPage 1 of 2
SU001-02Title:
REAR BEARING O-RING SERVICE TIP
Models:
'97 ± '01 Camry, '00 ± '02 Avalon &
'99 ± '02 Solara
Technical Service
BULLETIN
March 1, 2002
When replacing the rear hub bearing assemblies on 1997 ± 2001 model year Camry,
2000 ± 2002 Avalon and 1999 ± 2002 Solara vehicles, replace the O±ring.
1997 ± 2001 model year Camry vehicles.
2000 ± 2002 model year Avalon vehicles produced before the VIN shown below.
1999 ± 2002 model year Solara vehicles produced before the VIN shown below.
MODELSTARTING VIN
Avalon4T1BF28B#2U223623
Solara2T1##2#P#2C005335
PART NUMBERPART NAME
90301±63006O±Ring
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty±±±±
REMOVAL
1. Remove Rear Wheel.
Torque: 103 N m (1,050 kgf cm, 76 ft lbf)
2. With Disc Brake:
Remove Brake Caliper and Disc.
A. Remove the brake caliper and disc.
Torque: 47 N m (475 kgf cm, 34 ft lbf)
B. Support the brake caliper securely.
3. With Drum Brake:
Remove Brake Drum.
SUSPENSION
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Warranty
Information
Repair
Procedure
Page 4700 of 4770
REAR BEARING O±RING SERVICE TIP ± SU001-02March 1, 2002
Page 2 of 2
4. Remove Rear Axle Hub.
A. Remove the 4 bolts and rear
axle hub.
Torque: 80 N m (820 kgf cm, 59 ft lbf)
B. Remove the O±ring.
HINT:
At the time of installation, coat the new
O±ring with MP grease.
NOTE:
Please ensure that the O±ring is
replaced with a new service part when
installing the bearing assembly.
C. With Drum Brake:
Remove the bolt, and disconnect
the flexible hose from the shock
absorber.
Torque: 29 N m (300 kgf cm, 22 ft lbf)
D. Support the backing plate
securely.
5. With ABS:
Remove ABS Speed Sensor.
Torque: 8.0 N m (82 kgf cm, 71 in lbf)
INSTALLATION
Installation is in the reverse order of
removal.
Bolt
BoltBolt
Bolt
Page 4707 of 4770
Page 3 of 6
TRANSMISSION OIL COOLER INSTALLATION ± TC003±97 October 17, 1997
Procedure2. Cooler Installation:
(Continued)
A. Install the 140 mm (5.51º) hose to
the oil cooler tube No. 1 as shown.
NOTE:
Install the hose clamp with the hose
clamp clip at the position shown, and
use pliers to pull off the clip in the
direction indicated by the arrow.
B. Install the tube bracket onto the left
side of the front suspension
member with the 2 bolts as shown.
Torque: 62 in±lbf
(7 N±m / 71 kgf±cm)
C. Install the 130 mm (5.12º) hoses
and the 180 mm (7.09º) hose to the
oil cooler tube No. 2 as shown.
NOTE:
Install the hose clamps with the hose
clamp clips at the positions shown,
and use pliers to pull off the clips in
the direction indicated by the arrows.
Fig. 5
Oil Cooler Tube No. 1
140 mm Hose
5 mm (0.20º)
Fig. 6
Fig. 7
5 mm (0.20º)
180 mm Hose Oil Cooler Tube No. 2
130 mm Hose
Page 4708 of 4770
TRANSMISSION OIL COOLER INSTALLATION ± TC003±97 October 17, 1997
ProcedureD. Remove the lower side clip of the
(Continued) radiator side LH deflector.
E. Install the tube bracket with the bolt
on the side member.
Torque: 62 in±lbf
(7 N±m / 71 kgf±cm)
F. Reinstall the lower side clip
of the radiator LH deflector.
G. Connect the hoses from the oil
cooler tube No. 2 to the oil cooler
tube No.1.
NOTE:
Install the hose clamps with the hose
clamp clips at the positions shown, and
use pliers to pull off the clips in the
direction indicated by the arrows.
H. Disconnect the hose from the oil
cooler pipe of the radiator LH side.
NOTE:
Place a container below vehicle to catch
any leaking ATF. Remove the other end
of this hose from transaxle and discard.
I. Connect the hose from oil cooler
tube No.1 to the oil cooler pipe of
the radiator LH side.
NOTE:
Install the hose clamps with the hose
clamp clips at the positions shown, and
use pliers to pull off the clips in the
direction indicated by the arrows.
Page 4 of 6
Fig. 8
Oil Cooler Tube No. 1
Front Suspension Member
5 mm (0.20º)
Fig. 9
Fig. 10
5 mm (0.20º)
