1999 TOYOTA CAMRY differential

fuel reserve winter tyres catalytic converter manual radio set trailer instrument panel

Page 1654 of 4592

TOYOTA CAMRY 1999 Service Repair Manual DI±442
± DIAGNOSTICSAUTOMATIC TRANSAXLE (A541E)
677 Author: Date:
(b) Clearance the DTC.
The following actions will erase the DTC and freezed
frame data. Operating an OBD II scan tool (complying
w

DI±442
± DIAGNOSTICSAUTOMATIC TRANSAXLE (A541E)
677 Author: Date:
(b) Clearance the DTC.
The following actions will erase the DTC and freezed
frame data. Operating an OBD II scan tool (complying
with SAE J1978) or TOYOTA hand±held tester to erase
the codes.
(See the OBD II scan tool's instruction book for operating
instructions.)
4. ROAD TEST
NOTICE:
Perform the test at normal operating ATF temperature 50 ± 80 °C (122 ± 176 °F).
(a) D POSITION TEST
Shift into the D position and fully depress the accelerator pedal and and check the following points:
(1) Check up±shift operation.
1 " 2, 2 " 3 and 3 " O/D up±shift takes place, at the shift point shown in the automatic shift
schedule (See page SS±56).
HINT:
O/D Gear Up±shift Prohibition Control (1. Coolant temp. is 60 °C (140 °F) or less. 2. If there is a 10
km/h (6 mph) difference between the set cruise control speed and vehicle speed.)
O/D Gear Lock±up Prohibition Control (1. Brake pedal is depressed. 2. Coolant temp. is 60 °C
(140 °F) or less.)
(2) Check for shift shock and slip.
Check for shock and slip at the 1 " 2, 2 " 3 and 3 " O/D up±shifts.
(3) Check for abnormal noises and vibration.
Run at the D position lock±up or O/D gear and check for abnormal noises and vibration.
HINT:
The check for the cause of abnormal noises and vibration must be done very thoroughly as it could also be
due to loss of balance in the differential torque converter clutch, etc..
(4) Check kick±down operation.
While running in the D position, 2nd, 3rd and O/D gears, check to see that the possible kick±down
vehicle speed limits for 2 " 1, 3 " 2 and O/D " 3 kick±downs conform to those indicated on
the automatic shift schedule (See page SS±56).
(5) Check abnormal shock and slip at kick±down.
(6) Check the lock±up mechanism.
Drive in D position, O/D gear, at a steady speed (lock±up ON) of about 60 km/h (37 mph).
Lightly depress the accelerator pedal and check that the engine speed does not change
abruptly.
If there is a big jump in engine speed, there is no lock±up.
(b) 2 POSITION TEST
Shift into the 2 position and fully depress the accelerator pedal and check the following points:
(1) Check up±shift operation.
Check to see that the 1 " 2 up±shift takes place and that the shift point conforms to the automatic
shift schedule (See page SS±56).
HINT:
There is no O/D up±shift and lock±up in the 2 position.
(2) Check engine braking.
While running in the 2 position and 2nd gear, release the accelerator pedal and check the engine
braking effect.
(3) Check for abnormal noises during acceleration and deceleration, and for shock at up±shift and
down±shift.

Page 1769 of 4592

TOYOTA CAMRY 1999 Service Repair Manual ± DIAGNOSTICSANTI±LOCK BRAKE SYSTEM (BOSCH Made)
DI±557
792 Author: Date:
DTC 37 Speed Sensor Rotor Faulty
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
37
Detection of any of co

Page 2289 of 4592

TOYOTA CAMRY 1999 Service Repair Manual ± DIAGNOSTICSAUTOMATIC TRANSAXLE
DI±137
(b) Clearance the DTC.
The following actions will erase the DTC and freeze frame
data. Operating an OBD II scan tool (complying with SAE
J1978) or hand±held

± DIAGNOSTICSAUTOMATIC TRANSAXLE
DI±137
(b) Clearance the DTC.
The following actions will erase the DTC and freeze frame
data. Operating an OBD II scan tool (complying with SAE
J1978) or hand±held tester to erase the codes.
(See the OBD II scan tool's instruction book for operating
instructions.)
4. ROAD TEST
NOTICE:
Perform the test at normal operating ATF temperature 50 ± 80 °C (122 ± 176 °F).
(a) D position test
Shift into the D position and fully depress the accelerator pedal and and check the following points:
(1) Check up±shift operation.
1 " 2, 2 " 3 and 3 " O/D up±shifts take place, at the shift point shown in the automatic shift
schedule (See Pub. No. RM654U on page SS±54).
HINT:
O/D Gear Up±shift Prohibition Control (1. Coolant temp. is 50 °C (122 °F) or less. 2. If there is a 10
km/h (6 mph) difference between the set cruise control speed and vehicle speed.)
O/D Gear Lock±up Prohibition Control (1. Brake pedal is depressed. 2. Coolant temp. is 50 °C
(122 °F) or less.)
(2) Check for shift shock and slip.
Check for shock and slip at the 1 " 2, 2 " 3 and 3 " O/D up±shifts.
(3) Check for abnormal noises and vibration.
Run at the D position lock±up or O/D gear and check for abnormal noises and vibration.
HINT:
The check for the cause of abnormal noises and vibration must be done very thoroughly as it could also be
due to loss of balance in the differential or torque converter clutch, etc.
(4) Check kick±down operation.
While running in the D position, 2nd, 3rd and O/D gears, check to see that the possible kick±down
vehicle speed limits for 2 " 1, 3 " 2 and O/D " 3 kick±downs conform to those indicated on
the automatic shift schedule (See Pub. No. RM654U on page SS±54).
(5) Check abnormal shock and slip at kick±down.
(6) Check the lock±up mechanism.
Drive in D position, O/D gear, at a steady speed (lock±up ON) of about 75 km/h (47 mph).
Lightly depress the accelerator pedal and check that the engine speed does not change
abruptly.
If there is a big jump in engine speed, there is no lock±up.
(b) 2 position test
Shift into the 2 position and fully depress the accelerator pedal and check the following points:
(1) Check up±shift operation.
Check to see that the 1 " 2 up±shift takes place and that the shift point conforms to the automatic
shift schedule (See Pub. No. RM654U on page SS±54).
HINT:
There is no O/D up±shift and lock±up in the 2 position.
(2) Check engine braking.
While running in the 2 position and 2nd gear, release the accelerator pedal and check the engine
braking effect.

Page 2839 of 4592

TOYOTA CAMRY 1999 Service Repair Manual IN04Q±03
IN±36
± INTRODUCTIONTERMS
36 Author: Date:
TERMS
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti±Lock Brake System
ACAlternating Current
ACCAccessory
ACISAcoustic Control

Page 2840 of 4592

TOYOTA CAMRY 1999 Service Repair Manual ± INTRODUCTIONTERMS
IN±37
37 Author: Date:
DCDirect Current
DEFDefogger
DFLDeflector
DIFF.Differential
DIFF. LOCKDifferential Lock
D/INJDirect Injection
DLIDistributorless Ignition
DOHCDouble Over

Page 2841 of 4592

TOYOTA CAMRY 1999 Service Repair Manual IN±38
± INTRODUCTIONTERMS
38 Author: Date:
HIDHigh Intensity Discharge (Head Lamp)
HSGHousing
HTHard Top
HWSHeated Windshield System
IACIdle Air Control
ICIntegrated circuit
IDIIndirect Diesel Inj

Page 2845 of 4592

TOYOTA CAMRY 1999 Service Repair Manual IN±42
± INTRODUCTIONTERMS
42 Author: Date:
HO2SHeated Oxygen SensorHeated Oxygen Sensor (HO2S)
IACIdle Air ControlIdle Speed Control (ISC)
IATIntake Air TemperatureIntake or Inlet Air Temperature

Page 2880 of 4592

TOYOTA CAMRY 1999 Service Repair Manual IN04Q±03
IN±34
± INTRODUCTIONTERMS
34 Author: Date:
TERMS
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti±Lock Brake System
ACAlternating Current
ACCAccessory
ACISAcoustic Control

Load next 8 pages

Page: < prev 1-10 ... 25-32 33-40 41-48 49-56 57-64 65-72 73-80 81-88 89-96 ... 112 next >

radiator wipers tire pressure reset air bleeding key fob battery oil filter