1999 TOYOTA CAMRY torque

SF0DT±03
B01285
Vacuum Hose

Gasket
Throttle Body
Water Bypass Hose
Air Hose (California)Accelerator Cable
Throttle Cable
(A/T)
Throttle Position Sensor
Connector
IAC Valve Connector
Air Cleaner Cap Air Cleaner Hose
IAC Valve
VSV Connector
for EVAPEVAP Hose
IAT Sensor
Connector PCV HoseEVAP Hose
EVAP Hose
19 (195, 14)

Gasket
Throttle Body
N´m (kgf´cm, ft´lbf): Specified torque

Non±reusable part
SF±36
± SFI (5S±FE)IDLE AIR CONTROL (IAC) VALVE
1469 Author: Date:
COMPONENTS

SF0EE±03
B06350SST
P01630
Ohmmeter
No Continuity
± SFI (5S±FE)KNOCK SENSOR
SF±57
1490 Author: Date:
INSPECTION
1. REMOVE KNOCK SENSOR 1
(a) Disconnect the knock sensor connector.
(b) Using SST, remove the knock sensor.
SST 09816±30010
2. INSPECT KNOCK SENSOR 1
Using an ohmmeter, check that there is no continuity between
the terminal and body.
If there is continuity, replace the sensor.
3. REINSTALL KNOCK SENSOR 1
(a) Using SST, install the knock sensor.
SST 09816±30010
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(b) Connect the knock sensor connector.

SF0EB±03
B06358
No.3 Exhaust Manifold Heat Insulator
A/F Sensor Connector
Clamp
A/F Sensor
N´m (kgf´cm, ft´lbf): Specified torque
44 (450, 32)
SF±58
± SFI (5S±FE)AIR±FUEL RATIO (A/F) SENSOR (California)
1491 Author: Date:
AIR±FUEL RATIO (A/F) SENSOR (California)
COMPONENTS

SF0EC±04
B06365
Ohmmeter
+B
HT
± SFI (5S±FE)AIR±FUEL RATIO (A/F) SENSOR (California)
SF±59
1492 Author: Date:
INSPECTION
1. INSPECT HEATER RESISTANCE OF A/F SENSOR
(a) Disconnect the A/F sensor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals +B and HT.
Resistance: 0.8 ± 1.4 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(c) Reconnect the A/F sensor connector.
2. INSPECT OPERATION OF A/F SENSOR
(See page DI±152)

SF0EH±03
B06359
Heated Oxygen Sensor
(Bank 1 Sensor 1) Connector
Heated Oxygen Sensor (Bank 1 Sensor 1)Clamp
44 (450, 32)
N´m (kgf´cm, ft´lbf) : Specified torque
SF±60± SFI (5S±FE)HEATED OXYGEN SENSOR (Bank 1 Sensor 1/Except
Calif.)
1493 Author: Date:
HEATED OXYGEN SENSOR (Bank 1 Sensor 1/Except Calif.)
COMPONENTS

SF0EI±03
B06363
Ohmmeter
HT
+B
± SFI (5S±FE)HEATED OXYGEN SENSOR (Bank 1 Sensor 1/Except
Calif.)SF±61
1494 Author: Date:
INSPECTION
1. INSPECT HEATER RESISTANCE OF HEATED OXY-
GEN SENSOR
(a) Disconnect the oxygen sensor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals +B and HT.
Resistance: 11 ± 16 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(c) Reconnect the oxygen sensor connector.
2. INSPECT OPERATION OF HEATED OXYGEN SEN-
SOR (See page DI±66)

SF0EJ±03
Z19284
Passenger's Seat
Connector
for Seat
Heated Oxygen Sensor
Connector
(Bank 1 Sensor 2)
Grommet Clamp Heated Oxygen Sensor
(Bank 1 Sensor 2)
37 (375, 27)
44 (450, 32)
N´m (kgf´cm, ft´lbf): Specified torque SF±62
± SFI (5S±FE)HEATED OXYGEN SENSOR (Bank 1 Sensor 2)
1495 Author: Date:
HEATED OXYGEN SENSOR (Bank 1 Sensor 2)
COMPONENTS

SF0EK±03
S05303
Ohmmeter
HT +B
± SFI (5S±FE)HEATED OXYGEN SENSOR (Bank 1 Sensor 2)
SF±63
1496 Author: Date:
INSPECTION
1. INSPECT HEATER RESISTANCE OF HEATED OXY-
GEN SENSOR
(a) Disconnect the oxygen sensor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals +B and HT.
Resistance: 11 ± 16 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(c) Reconnect the oxygen sensor connector.
2. INSPECT OPERATION OF HEATED OXYGEN SEN-
SOR (See page DI±75)