1995 TOYOTA SUPRA differential

09223±15030 Oil Seal & Bearing Replacer
09229±55010 Oil Cooler Relief Valve Wrench
(2JZ±GTE M/T)
Side gear shaft oil seal
installation
(Except 2JZ±GTE M/T)
Rear bearing outer race
installation
Drive pinion nut removal
and installation
09250±10011 Replacer Set ªAº
(09252±10010) No. 1 Replacer Handle
(09255±10011) Crankshaft Rear Bearing Remover
& Replacer
09308±00010 Oil Seal Puller
09316±12010 Transfer Bearing ReplacerDifferential mounting cushion
removal
Side gear shaft oil seal removal
Drive pinion oil seal removal
(2JZ±GTE M/T)
Rear bearing installation
(Except 2JZ±GTE M/T)
Dust cover installation
Drive pinion oil seal installation
(Except 2JZ±GTE M/T)
Drive pinion oil seal
installation
(2JZ±GTE M/T)
Drive pinion oil seal
installation
09316±20011 Transfer Bearing Replacer
09316±60010 Transmission & Transfer
Bearing Replacer
(09316±00010) Replacer Pipe
(09316±00040) Replacer ªCº
(09316±00070) Replacer ªFº
REAR DIFFERENTIAL
PREPARATION
SST (SPECIAL SERVICE TOOLS)
± SUSPENSION AND AXLEREAR DIFFERENTIALSA±53

09330±00021 Companion Flange Holding Tool
09502±12010 Differential Bearing Replacer(Except 2JZ±GTE M/T)
Drive pinion oil seal
installation
09502±24010 Bearing Replacer
09502±24010 Differential Side Gear Shaft
Puller
09502±10012 Replacer Set ªBº
(09558±10010 Rear Axle Shaft Oil Seal
Replacer
09570±24010 Differential Mounting Cushion
Remover & Replacer
09608±30012 Front Hub & Drive Pinion Bearing
Tool Set
(09608±04030)Front Hub Inner Bearing Cane
Replacer
09608±32010 Steering Knuckle Oil Seal
Replacer(Except 2JZ±GTE M/T)
Side gear oil seal
installation
09608±35014 Axle Hub Drive Pinion Bearing
Tool Set
(09608±06020) Handle
(09608±06040)Front Hub Inner Bearing Cone
Replacer
(09608±06090) Front Hub Outer & Steering Worm
Bearing ReplacerDust deflector removal
SA±54± SUSPENSION AND AXLEREAR DIFFERENTIAL

(09608±06100) Front Hub Outer Bearing Replacer
(09608±06110) Front Hub Inner & Drive Pinion
Front Bearing Cup Replacer
(Except 2JZ±GTE M/T)
Side bearing installation
(2JZ±GTE M/T) Dust
deflector installation
(09608±06180) Drive Pinion Rear Bearing Cup
Replacer
(09608±06210) Rear Axle Bearing Replacer
09631±32020Seal Ring Tool
09710±30050 Suspension Arm Bushing Replacer
09726±36010 Lower Control Arm Bushing
Replacer(2JZ±GTE M/T)
Side bearing installation
09950±00020Bearing Remover
09950±40010 Puller B Set
(Except 2JZ±GTE M/T)
Side bearing outer race removal
Front bearing outer race
installation
(09608±06120) Front Hub Outer Bearing Cup
Replacer
(09608±06150)Rear Hub Outer Bearing Cup
Replacer
Dust cover installation
(2JZ±GTE M/T)
Side bearing outer race
Carrier retainer installation
(09608±06160) Rear Hub Inner Bearing Cup
Replacer(2JZ±GTE M/T)
Rear bearing outer race
installation
(Except 2JZ±GTE M/T)
Carrier retainer installation
(Except 2JZ±GTE M/T)
Side bearing outer race
installation
(2JZ±GTE M/T)
Dust cover installation
Side bearing installation
Rear bearing removal
Dust deflector and dust cover
removal
Carrier retainer removal
Side bearing removal
± SUSPENSION AND AXLEREAR DIFFERENTIALSA±55

RECOMMENDED TOOLS
09924±12361 Deep socket Wrench 36.
09025±00010 Torque Wrench (30 kgf
cm)
09031±00030 Pin Punch.
(2JZ±GTE M/T)
Drive pinion nut removal
and installation
Differential preload
(Conventional differential only)
Pinion shaft removal
EQUIPMENT
 
 
Dial indicator with magnetic base 
 
 
 
Micrometer 
 
 
 
Torque wrench 
 
 
 
Vernier calipers 
 
SSM (SPECIAL SERVICE MATERIALS)
 
 
 
 
08826±00090 Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG) 
 
 
 
Differential carrier X Cover
 
 
 
 
08833±00100 THREE BOND 1360K or equivalent 
 
 
 
Differential case X Ring gear
LUBRICANT
 
 Item
 
 Capacity
 
 Classification
 
 
 
 
Differential oil
 
 
 
 
1.35 liters (1.43 US qts, 1.19 lmp.qts)
 
 
 
 
API GL±5 Hypoid gear oil
[Above ± 18°C (0°F)]
SAE 90
[Below ± 18°C (0°F)]
SAE 80W or 80W±90
SA±56± SUSPENSION AND AXLEREAR DIFFERENTIAL

ON±VEHICLE REPAIR
COMPONENTS
± SUSPENSION AND AXLEREAR DIFFERENTIALSA±57

SIDE GEAR SHAFT OIL SEAL
REPLACEMENT
1. DRAIN DIFFERENTIAL OIL
2. REMOVE REAR DRIVE SHAFT
(See page SA±46)
3. REMOVE SIDE GEAR SHAFT
(a) 2JZ±GTE M/T only:
Equally tighten both bolts at the same time and pull out the
side gear shaft.
NOTICE: Pull out the side gear shaft until a nut can fit be-
hind the shaft. Pulling the shaft out too far will damage
the dust cover.
(b) Using SST and 2 bolts, nuts, remove the side gear shaft.
SST 09520±24010
4. REMOVE SNAP RING
Remove the snap ring from the side gear shaft.
5. REMOVE SIDE GEAR SHAFT OIL SEAL
Using SST, remove the oil seal.
SST 09308±00010
6. INSTALL SIDE GEAR SHAFT OIL SEAL
(a) Using SST and a hammer, drive in a new oil seal.
2JZ±GTE M/T:
SST 09223±15030, 09608±35014 (09608±06020)
Except 2JZ±GTE M/T:
SST 09608±32010, 09608±35014 (09608±06020)
(b) Apply MP grease to the oil seal lip. SA±58
± SUSPENSION AND AXLEREAR DIFFERENTIAL

7. INSTALL SIDE GEAR SHAFT
(a) Install a new snap ring to the side gear shaft.
(b) Coat MP grease onto the snap ring.
(c) Using a hammer and brass bar, tap in the side gear shaft to
the differential.
NOTICE: Be careful not damage the side gear shaft and
oil seal.
HINT: Whether or not the side gear shaft is making contact
with the pinion shaft can be determined by the sound or feel-
ing when driving it in.
8. CHECK INSTALLATION OF SIDE GEAR SHAFT
Check that the side gear shaft will not come out by trying to
pull it out by hand.
9. INSTALL REAR DRIVE SHAFT
(See page SA±46)
10. FILL DIFFERENTIAL WITH OIL
Oil grade:
API GL±5 Hypoid gear oil
Viscosity:
Above ± 18°C (0°F) SAE 90
Below ± 18°C (0°F) SAE 80W±90 or 80W
Capacity:
1.35 liters (1.43 US qts, 1.19 lmp. qts)
± SUSPENSION AND AXLEREAR DIFFERENTIALSA±59

ASSEMBLY REMOVAL AND
INSTALLATION
COMPONENTS
SA±60± SUSPENSION AND AXLEREAR DIFFERENTIAL