2021 MERCEDES-BENZ V-CLASS Owners Manual

Enhanced f
Enhanced f
og light function
og light function
The enhanced fog light function reduces self-daz-
zling and impr ovesth e illumination of the edge of
th e car riag ewa y. If
yo ur speed is below 70 km/h and thefo g light
has been switched on, the enhanced fog light func-
tion will automatically be activated.
The enhanced fog light function will automatically
be deactivated aTer activation in thefo llowing
cases:
R Your speed is greater than 100 km/h.
R The fog light is switched o..
Switc Switc hing t
hing t he Int
he Int ellig
elligent Light Syst
ent Light Syst em
emon/o.
on/o. #
Press theò button tocall up the list of
menus. #
Use the: or9 button toselect Set-
tings . #
Press thea button. #
Use the: or9 button toselect Lights. #
Press thea button. #
Use the: or9 button toselect Intelli-
gent Light System .
If th e Intelligent Light System has been
switched on, the display will show theL
symbol in yellow on the inst rument cluster. #
Press thea button.
When you switch on the Intelligent Light System
function, you will enable thefo llowing functions:
R Motorw ay mode
R Active light function
R Cornering light
R Enhanced fog light function
% Ifyo u set the low beam for driving on theright
or leT, the display will show the display mes-
sage Inactive for left-side traffic orInactive
for right-side traffic intheLights submenu
instead of Intelligent Light System
(/ page 189). This display message will appear only if
the setting for driving on the
ri ght or leT is the opposite toyour vehicle's
national version.
% You can /nd fur ther information in "Intelligent
Light System" (/ page 109). A
A
dap
dap tiv
tive Highbeam Assist
e Highbeam Assist A
A
dap
dap tiv
tive Highbeam Assis
e Highbeam Assist function t function &
W
WARNING
ARNING Risk of accident despite Adap-
tive Highbeam Assist
Ad aptive Highbeam Assist does not react to:
R road users without lights, e.g. pedestrians
R road users with poor lighting, e.g. cyclists
R road users whose lighting is obstructed,
e.g. bya bar rier
On very rare occasions, Adaptive Highbeam
Assist may failto recognise other road users
with their own lighting, or may recognise them
to o late.
In these, or in similar situations, the automatic
high beam will not be deactivated or will be
activated despite the presence of other road
users. #
Always obser vethero ad and tra1c con-
ditions carefully and switch o. the high
beam in good time. The
Adaptive Highbeam Assist automatically
switches between thefo llowing settings:
R Low beam
R High beam 110 110
Light and vision

The system de
tects that vehicle lights are
approaching in the opposite direction or driving
ahead of theve hicle.
If yo ur speed is greater than 30 km/h and no other
ro ad users are de tected, high beam will automati-
cally be switched on.
If yo ur speed is greater than 25 km/h, the head-
lamp range will be controlled automatically
depending on the distance from other road users.
High beam will automatically be deacti vated in the
fo llowing cases:
R Your speed is lo werth an 25 km/h.
R Other road users ha vebeen de tected.
R The road is su1ciently illuminated.
Syst Syst em limits
em limits
Ad aptive Highbeam Assist cann ottake thero ad,
we ather or tra1c conditions into consideration.
The de tection of obs tacles may be restric ted if:
R visibility is poor, e.g. in fog, heavy rain or sno w.
R the sensors are dirty or co vered.
Ad aptive Highbeam Assist is only an aid. You are
re sponsible for ensuring cor rect vehicle lighting in
accordance with the pr evailing light, visibility and
tra1c conditions.
The system's optical sensor is located behind the
windscreen near theove rhead control panel.
Switc
Switc hing Highbeam Assis hing Highbeam Assist ton/o.
on/o.
R
R eq
eq uir
uir ements:
ements:
R The light switch is in theà position. #
T
To switc
o switc h on:
h on:switch on high beam using the
combination switch.
When the high beam is switched on automati-
cally in the dar k, the_ indicator lamp will
light up on the inst rument cluster displa y. #
T To switc
o switc h
ho.:
o.: switch o. high beam using the
combination switch. A
A
dap
dap tiv
tive Highbeam Assis
e Highbeam Assis t Plus
t Plus A
A
dap
dap tiv
tive Highbeam Assis
e Highbeam Assis t Plus function
t Plus function &
W
WARNING
ARNING Risk of accident despite Adap-
tive Highbeam Assist Plus
Ad aptive Highbeam Assist Plus does not react
to:
R road users without lights, e.g. pedestrians
R road users with poor lighting, e.g. cyclists
R road users whose lighting is obstructed,
e.g. bya bar rier
On very rare occasions, Adaptive Highbeam
Assist Plus may failto recognise other road
users with their own lighting, or may recognise
th em too late.
In these, or in similar situations, the automatic
high beam will not be deactivated or will be
activated despite the presence of other road
users. #
Always obser vethero ad and tra1c con-
ditions carefully and switch o. the high
beam in good time. Ad
aptive Highbeam Assist Plus cann ottake into
account road, weather or tra1c conditions.
De tection may be restric ted in thefo llowing cases:
R In poor visibility, e.g. fog, heavy rain or snow
R ifth ere is dirt on the sensors or the sensors
are obscured
Ad aptive Highbeam Assist Plus is only an aid. Yo u
are responsible for ensuring cor rect vehicle light-
ing in accordance with the pr evailing light, visibility
and tra1c conditions. Light and vision
111 111

Ad
aptive Highbeam Assist Plus switches automati-
cally between thefo llowing light types:
R Low beam
R Partial high beam
R High beam
Pa rtial high beam uses high beam toshine past
ot her road users rather than dazzling them. The
low beam illumination area co vers theve hicle in
front.
At speeds lo werth an 25 km/h or if there is insu1-
cient street lighting, Highbeam Assist Plus will per-
fo rm thefo llowing actions:
R Partial high beam and high beam will be auto-
matically deactivated.
R The K indicator lamp on the inst rument
cluster will go out. The _symbol for High-
beam Assist Plus will remain switched on.
At speeds greater than 30 km/h, Highbeam Assist
Plus will per form thefo llowing actions:
R If no other road users are de tected, high beam
will be switched on.
R Ifot her road users are de tected, partial high
beam will be switched on.
R The K indicator lamp on the inst rument
cluster will light up.
At speeds greater than 40 km/h, Highbeam Assist
Plus will per form thefo llowing actions:
R If no other road users are de tected and the
ro ad is st raight, high beam will be switched on.
R If highly re0ective signs are de tected, high
beam will automatically be switched o..
R Ifot her road users are de tected, partial high
beam will be switched on automaticall y.
R The K indicator lamp on the inst rument
cluster will light up.
The system's optical sensor is located behind the
windscreen near theove rhead control panel.
Switc
Switc hing A hing A dap
daptiv
tive Highbeam Assis
e Highbeam Assist Plus t Pluson/o.
on/o.
R
R eq
eq uir
uir ements:
ements:
R The light switch is in theà position. #
T
To switc
o switc h on:
h on: switch on high beam using the
combination switch.
When the high beam is switched on automati-
cally in the dar k, the_ indicator lamp will
light up on the inst rument cluster displa y. #
T To switc
o switc h
ho.:
o.: switch o. high beam using the
combination switch. Se
Se
tting t
tting t he e
he ext
xter
er ior lighting
ior lighting switc
switch-o.
h-o. dela
delay time
y time R
R
eq
eq uir
uir ements:
ements:
R The light switch is in theà position.
Multimedia system: 4 © 5
Settings 5
Lights
5 Ext. light. del. sw. off #
Set a swit ch-o. delay time.
When theve hicle is switched o., theex terior light-
ing will be activated forth e set time. A
A
ctiv
ctiv ating and deactiv
ating and deactiv ating t
ating the surr
he surr ound lighting
ound lighting Multimedia system:
4 © 5
Settings 5
Lights
5 Surround lighting #
Activate or deactivate the function.
The exterior lighting will remain on for 40 seconds
aTer theve hicle is unloc ked. When you start the
ve hicle, the sur round lighting will be deactivated
and the automatic driving lights activated. A
A
djus
djusting t ting t he int
he int er
erior lighting
ior lighting A
A
djus
djusting t ting t he int
he int er
erior lighting
ior lighting F
F
r
ront ov
ont overerhead contr
head contr ol panel
ol panel Interior lighting buttons (e
xample: comfort over-
head cont rol panel)
1p Front-leT reading lamp
2| Automatic interior lighting control
3c Front interior lighting
4w Rear or load compartment lighting
5p Front-right reading lamp #
T
To switc
o switc h
hon/o.:
on/o.: pressthe cor responding but-
to n1 –5. 112
112
Light and vision

The la
yout and number of buttons depend on the
equipment.
Oper
Oper ating unit in t
ating unit in t hegr
he grab handle ab handle 1p
Rear reading lamp #
T To switc o switc h
hon/o.:
on/o.: press button 1. A
A
djus
djusting ambient lighting ting ambient lighting Multimedia system:
4 © 5
Comfort 5
Ambient lighting
Se
Se tting t
tting t he colour
he colour #
Select Colour. #
Set there qu ired colour.
or #
Select a colour combination.
A
A djus
djusting t ting t he br
he br ightness
ightness #
Select Brightness. #
Adjust the brightness. Switc
Switc
hing t
hing t he int
he inter
erior lighting
ior lighting switc
switch-o.
h-o. dela
delay time
y time
on/o.
on/o. Multimedia system:
4 © 5
Settings 5
Lights
5 Int. light. del. sw. off #
Switch the swit ch-o. delay time on or o..
When this function is active, the interior light-
ing switches on automatically when the engine
is unloc ked or switched o.. Changing bulbs
Changing bulbs
Ins
Instr
tructions f
uctions f or r
or replacing light sour
eplacing light sour ces
ces &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts whilst replacing a bulb
Bulbs, lamps and plug connectors can become
ve ry hot during operation. When
replacing a bulb, you could burn yourself
on these component parts. #
Allow the component parts tocool down
before replacing the bulbs. Impor
tant sa fety no tes
R Before changing the bulbs, switch o. theve hi-
cle's lighting system. This will pr event a short
circuit.
R Use only spare bulbs of the same type and with
th e cor rect voltage.
R Use bulbs only in enclosed lamps that ha ve
been designed forth em.
R Do not use any light source that has been
dropped or has scratches on its glass tube.
Otherwise, the light source may explode.
R The light source may explode under thefo llo w-
ing conditions:
- if it is hot and youto uch it
- ifyo u drop it
- ifyo u scratch it
R Stains on the glass tube will reduce the service
life of the light source. Do not touch the glass
tube with your bare hands. If necessar y,clean
th e glass tube with alcohol or spirits while it is
cold and wipe it down with a lint-fre e cloth.
R Protect light bulbs from humidity and do not
bring them into contact with liquids.
Alw ays ensu rethe bulbs are /rmly secured.
Ha ve thefo llowing light sources changed at a
qu ali/ed specialist workshop onl y:
R Additional turn signal lamps on the outside mir-
ror
R Bulbs in the licence plate lighting Light and vision
113
113

R
R
eplacing fr
eplacing fr ont light bulbs (v
ont light bulbs (v ehicles wit
ehicles with halog
h halogen
en
headlam
headlam ps)
ps) Ov
Ov
er
ervie
vie w of fr
w of fr ont light sour
ont light sour ce types
ce types 1
Additional turn signal lamp on the outside mir-
ro r: LED
2 Turn signal light: PY 21 W
3 Low beam: H7 55 W
4 High beam/standing/parking lights/d aytime
ru nning lights: H15 55 W/15 W
R
R eplacing light sour
eplacing light sour ces in t
ces in the headla mp
he headlamp
R
R eq
eq uir
uir ements:
ements:
R The lighting system is switched o..
R The appropriate front wheel is turned in wards.
R Lo
Lo w beam:
w beam: youre qu ire a H7 55 W light bulb.
R T
T ur
ur n signal light
n signal light: :yo ure qu ire a PY 21 W light
bulb.
R High beam / st
High beam / st anding/par
anding/parking lights / da y-
king lights / da y-
time r
time r unning lights:
unning lights: youre qu ire a H15 55 W/
15 W light bulb.
F
F itting/r
itting/r emo
emoving t
ving t he cov
he cov er in t
er in the fr
he front wheel ar ch
ont wheel ar ch #
T
To r
o r emov
emov e:
e:grip the centre of co ver1, slide it
upwards and pull it out.
The co ver will hang down wards on the strap. #
T To
o /t:
/t: insert co ver1 attheto p and slide it
down wards until it engages.
Lo
Lo w beam
w beam #
Remo vethe co ver in the front wheel ar ch. #
Turn housing co ver1 anti-clockwise and
re mo veit. #
Turn soc ket2 for low beam tothe leT and
pull it out. #
Pull the bulb out of soc ket2. #
Inse rtthe new bulb into soc ket2. #
Inse rtsoc ket2 and rotate itto theright to
tighten it. #
Press on housing co ver1 and ro tate itto the
ri ght totighten it. #
Replace the co ver in the front wheel ar ch.
High beam, st
High beam, st anding/par
anding/parking lights and da
king lights and da ytime
ytime
r
r unning lights
unning lights #
Open the bonnet. 114
114
Light and vision

#
Turn housing co ver1 anti-clockwise and
re mo veit. #
Pull out the bulb with soc ket2. #
Inse rtthe new bulb with soc ket2 and engage
it as far as it will go. #
Press on housing co ver1 and ro tate itto the
ri ght totighten it. #
Close the bonnet.
T
T ur
ur n signal light
n signal light #
Open the bonnet. #
Turn soc ket1 anti-clockwise and pull it out. #
Pull the bulb out of soc ket1. #
Inse rtthe new bulb into soc ket1. #
Inse rtsoc ket1 and turn it clockwise until it
engages. #
Close the bonnet. R
R
eplacing r
eplacing r ear bulbs
ear bulbs Ov
Ov
er
ervie
vie w of r
w of r ear light sour
ear light sour ce types
ce types Ve
hicles with standard tail lamp
1 Third brake light: LED
2 Licence plate lighting: LED
3 Rear fog light (driver's side): P 21 W
4 Reversing light: P 21 W
5 Brake light, tail light/parking lights: P 21 W
6 Turn signal light: P 21 W
Ve hicles with LED tail lamps 1
Third brake light: LED
2 Licence plate lighting: LED
3 Rear fog light (driver's side): LED
4 Reversing light: W 16 W
5 Brake light, tail light/parking lights: LED
6 Turn signal light: LED
R
R eplacing light sour
eplacing light sour ces in t
ces in the t
he tail lamp
ail lamp
R
R eq
eq uir
uir ements
ements
R The lighting system is switched o..
R St
Standar
andar d t
d tail lam
ail lam p:
p:youre qu ire a P 21 W light
source.
R LED t
LED t ail lam
ail lam p:
p:youre qu ire a W 16 W light
source.
R
R emo
emo ving t
ving t he t
he tail lamp
ail lamp
* NO
NOTE
TEDamage tothe paintwork during tail
lamp remo val The paintwork may be damaged when
theta il
lamps are remo ved. The tail lamp ma y,for
ex ample, scratch the paintwork when it is
re mo ved. #
Remo vetheta il lamps carefull y. #
Mercedes-Benz recommends having the
ta il lamp light sources replaced at a
qu ali/ed specialist workshop. Please no
tethat you can change the bulb of the
re ve rsing light only in the case of an LED tail lamp. #
Open theta ilgate.
% You will /nd a scr ewdriver in theve hicle tool
kit (/ page 250). #
Unscr ewtwo side scr ews1. Light and vision
115
115

#
Push tail lamp 2outwards against bolts 3
as far as it will go. #
Press tail lamp 2o. outwards and away from
bolts 3. #
Pull the connector o. the bulb mount of tail
lamp 2.
Inst
Inst alling t
alling t he t
he tail lamp
ail lamp #
Push the connector into the bulb mount of tail
lamp 2. #
Push tail lamp 2onto bolts 3from the side
and press it against theve hicle. #
Tighten two side scr ews1.
S S t tandar
andar d t
d tail lamp
ail lamp #
Unscr ewthre e scr ews1 and remo vebulb
mount 2from theta il lamp. Bulb mount
3
Turn signal light
4 Brake light, tail light, parking light
5 Reversing light
6 Rear fog light (only on the driver's side) #
Remo vetheta il lamp. #
Gently turn the bulb anti-clockwise and take it
out of the soc ket. #
Push the new bulb into the soc ket and turn it
clockwise toscr ew it in. #
Insert bulb mount 2into theta il lamp and
tighten all thre e scr ews1. #
Installth eta il lamp. LED t LED t
ail lamp
ail lamp #
Remo vetheta il lamp. #
Unscr ewhousing co ver1 byturning it anti-
clockwise. #
Turn the soc ket anti-clockwise and pull it out. #
Pull the bulb out of the soc ket. #
Inse rtthe new bulb into the soc ket. #
Inse rtthe soc ket and rotate it clockwise to
tighten it. #
Press on housing co ver1 and ro tate it cloc k-
wise totighten it. #
Install theta il lamp. R
R
eplacing int
eplacing int er
erior light bulbs
ior light bulbs R
R
eplacing light sour
eplacing light sour ces in t
ces in t he int
he inter
erior
ior
R
R eq
eq uir
uir ements:
ements:
R The interior lighting has been switched o..
R R
Rear and load com
ear and load com par
partment lam
tment lam p:
p:youre qu ire
a T10 6W xenon light sou rce.
R Int
Inter
erior and surr
ior and surr ound lighting:
ound lighting: youre qu ire a
W 5 W light source.
R Signal and ambient lam Signal and ambient lam p in t p in the t
he tailg
ailgat
ate:
e: you
re qu ire a W 5 W light source. 116
116
Light and vision

R
R
ear and load com
ear and load com par
partment lam
tment lam ps
ps #
Push in the catch spring of lens 1with a suit-
able object, e.g. a scr ewdriver, and then prise
o. the lens with the lamp housing. #
Push the lugs of soc ket2 inwa rds. #
Remo velight source 3from the lamp hous-
ing. #
Insert the new light source. #
Position the lens on the lamp housing and
engage it. #
Align the lens with the lamp housing and
engage it.
A
A dditional int
dditional int er
erior and surr
ior and surr ound lighting
ound lighting
Depending on the equipment, replacing the light
sources as described here applies tothefo llowing
lamps:
R The sun visor mir ror lamp
R The ambient lamp at the bottom of the front
door
R The ambient lamp on the inside of theta ilgate #
Push in the catch spring of lamp housing 1
with a suitable object, e.g. a scr ewdriver, and
prise o. lamp housing 1. #
Turn soc ket2 anti-clockwise and pull it out of
lamp housing 1. #
Pull bulb 3out of soc ket2. #
Push new bulb 3into soc ket2. #
Screw soc ket2 into lamp housing 1by
turning it clockwise. #
Place lamp housing 1in position on the leT
and engage it.
Signal and ambient lam
Signal and ambient lam p in t
p in the t
he tailg
ailgate
ate #
Push in the catch spring of the lamp housing
on the side of transparent lens 3with a suita-
ble object, e.g. a scr ewdriver, and prise o. the
lamp housing. #
Turn soc ket2 anti-clockwise and pull it out of
th e lamp housing. #
Pull the bulb out of soc ket2. #
Push the new bulb into soc ket2. #
Screw soc ket2 into the lamp housing by
turning it clockwise. #
Place the lamp housing in position at the side
of red lens 1and engage it. Light and vision
117
117