2016 AUDI A3 Owner´s Manual

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
When switched on, adaptive light adjusts to
curves depending on the vehicle speed and steer­ing wheel angle. This provides better lighting
through the curve. The system operates in a
speed range from approximately 6 mph (10 km/
h) to 68 mph (110 km/h).
Static cornering light* (vehicles with adaptive
light) -the cornering light switches on automati­
cally when the steering wheel is turned at acer­
tain angle at speeds up to approximately 44 mph
(70 km/h) and when the turn signal is activated
at speeds up to approximately 25 mph (40 km/
h). The area to the side of the vehicle is illuminat­
ed better when turning.
Speed dependent light distribution* -The speed
dependent light distribution adapts the light in
towns and on highways or expressways . Intersec­
tions can also be illuminated on vehicles with a
navigation system* .
Highway light function*
(Vehicles with adaptive light or LED headlights) -
This function adapts the lighting for highway
driving based on vehicle speed .
& WARNING
-Automatic headlights* are only intended to
assist the driver. They do not relieve the
driver of responsibility to check the head­
lights and to turn them on manually accord­
ing to the current light and visibility condi­
tions. For example, fog cannot be detected by the light sensors . So always switch on the
low beam under these weather conditions
and when driving in the dark
io.
-Accidents could occur if you cannot see the
road ahead of you well and if others on the
road cannot see you . Always switch your
headlightsonsothatyoucanseetheroad
ahead of you and others can see your vehicle
from behind.
- The rear fog lights should only be turned on
in accordance with traffic regulations, to
prevent glare for traffic behind your vehicle .
-If the battery has been discharging for a
while, the parking lights may switch off au­
tomatically to conserve the battery charge
Lights and Vision
for the next time the engine is started. Al·
ways make sure your vehicle complies with
legal regulations regarding sufficient and
safe lighting when parking it. Avoid using
the parking lights for several hours.
- Please observe legal regulations when using
the lighting systems described .
@ Tips
-The light sensor for the automatic head­
lights* is in the rearview mirror mount.
Therefore, do not place any stickers in this
area on the windshield.
- Some functions of the exterior lighting can
be adjusted
¢ page 48 .
-If you turn off the ignition while the exterior
lights are on and open the door, you will
hear a warning tone.
- In some market-specific versions, the tail
lights do not turn on when switching on the
daytime running lights .
- In cool or damp weather, the inside of the
headlights, turn signals and tail lights can
fog over due to the temperature difference
between the inside and outside. They will
clear shortly after switching them on. This
does not affect the service life of the light­
ing.
- A message will appear in the instrument
cluster if there is a malfunction in the light
sensor
¢ page 25.
Emergency flasher
Fig. 33 Inst rume nt panel: e merge ncy flasher butto n
The emergency flashers makes other drivers
aware of your vehicle in dangerous situations .
N Cl) M 0
> Cl) (0
47

Lights and Vision
.,. Press the~ button to switch the emergency
flashers on or off.
You can indicate a lane change or a turn whe n the
emergency f lashers are sw itched on by using the
turn signal lever. The emergency flashers stop
temporarily .
The emergency flashers also work when the igni ­
tion is turned off.
(0, Tips
You s hou ld sw itch the emergency flashers on
if:
- You are the last car in a traff ic jam so that
a ll other vehicles appro ach ing from be hind
can see yo u, or if
- You r vehicle has bro ke n down or you are
having an eme rgency, or if
- Y our vehicle is being towed or if you a re
tow ing another vehicle .
Turn signal and high beam lever
The lever operates the turn signals, the high
beams and the headlight fla sher.
F ig. 34 Turn signal and h igh bea m lever
Tu rn signal s¢¢
N
0
.... 9 ::i:
;ii
The turn signals activate when you move the lev­
er into a turn signal position when the ignition is
sw itched on.
(D -Turn signal
@ -Turn signal
The turn signal blinks three times if you tap the
lever (conven ience turn s ignal).
48
High beams and headlight flasher [D
Move the lever to the corresponding position:
@ -high beams on
@-high beams off or headlight flasher
The
II i ndicator light in the instrument cl uster
turns on.
A WARNING
High beams can cause glare for other drivers,
which increases the risk of an accident. For
this reason, only use the high beams or the
headlight flasher when they will not create
gla re for othe r drive rs .
Adjusting the exterior lighting
The settings are adjusted in the MMI.
.,. Select : the I MENU I button > Car > Systems *
control button > Vehicle settings > Exte rior
light ing .
Automatic headlights
Yo u can adjust the following settings in the Au­
tomati c headlights
menu:
Activation time -you can ad ju st if the headlights
swi tch on
Early , Medium or Late acco rd ing to t he
sensi tivity of the light sensor.
Audi adaptive light * -you can sw itch adaptive
li gh t
On an d Off .
Coming home, Leaving home*
The coming home f unction illuminates the area
outside the vehicle when you turn the ignition off
and open the driver 's door . To turn the function
o n, select
Lights when leaving car > On .
The leaving home illum inates the area outside
the ve hicle when you unlock the vehicle . To turn
the function on, se lec t
Lights when unlocking
car > On .
The coming home and leav ing home functions
o nl y operate when it is dark and the light sw itch
i s in the
AUTO pos ition . ..,.

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
Daytime running lights*
USA models :
the daytime running lig hts can be
switched on or off using the MMI. Sele ct
On or
Off .
Canada models :
this function ca nno t be switched
off. They activate au tom atically e ach time the ig­
n it ion is swi tched o n. Th is menu item is shown
with a "gray backgro und" .
Travel mode*
The headlig ht beam is asymmetrical. This pro­
v id es s tronge r illu mination on the side of the
r oad on whi ch you are driving. In ve hicles w it h
Xenon headlights* with turning light* or LED
headlight s*,
you must adjust the head lights
when yo u are driv ing in a co untry whe re the tra f­
f ic direction is opposite from your own country.
Otherw ise, oncoming traffic will be blinded by
the glare from t he headlights . An adjustment is
not needed in vehicles with Xenon head lights
witho ut t urning lights .
To prevent glare:
- Travel mode must be activated in vehicles wit h
Xenon headlights * and turning light* or LED
headlights*. Select: the
I MENU I button> Car >
Systems *
control button > Vehicle settings >
Exterior lighting > light for driving on left , for
example .
After you have adjusted the headlights, the fol ­
l owing message will appear:
l'iD Headlight converter active for driving on
left. Range reduced!
(D Tips
When travel mode is activa ted, a d is pl ay in
the dr iver information system in dicates this
each time you switch the ignition on .
Lights and Vision
Interior lighting
Front and rear interior lighting front
Fig. 35 Front headli ner: interio r lig htin g con trols (exam­
pl e)
Fi g. 36 Rea r head li ner : LED read ing lig hts* (examp le)
D epend ing on e quipme nt, the interior lighting
may diffe r from the ill ustra tion .
~- Inter io r ligh ting o n/off
[j]. Door contact switch. The interior lig hting is
contro lled automatically .
C:!J * -Read ing lights on/off
Interior lighting
T he re a re ot her op tion al i nte rior ligh ting func ­
tions* that are ava ilab le . Some func tions can be
adjusted in the MM
I. Select: the IM ENU I butto n >
Ca r > Systems* control button > Vehicle settings
> Interior lighting .
49

Lights and Vision
Instrument illumination
The brightness of the instrument cluster and the
center console can be adjusted .
Fig. 37 Instrument ill umination
Requirement: the light must be switched on.
~ Press the knob to release it .
~ Turn the knob toward"-" or"+" to reduce or in­
crease the brightness.
~ Press the knob again to return it to its original
position.
(D Tips
The needles and gauges in the instrument cluster illuminate when the headlights are off
and the ignition is switched one. The illumina­
tion reduces automatically and eventually
turns off as brightness outside decreases.
This function reminds the driver to turn the
headlights on at the appropriate time.
Vision
Adjusting the exterior mirrors
Fig. 38 Driver's door: knob for the ex ter ior mirrors (exam­
ple)
Turn the knob to the desired position:
50
0 - All adjustment functions are deactivated.
q;p -adjusting the left/right exterior mirror.
Move the knob in the desired direction.
4#1 -Heating* the mirror glass depending on the
outside temperature.
8 -Folding exterior mirrors*. You can select if
the mirrors fold in automatically when you lock
the vehicle In the
MMI* ~ page 40.
Front passenger's exterior mirror tilt
function*
To help you see the curb when backing into a
parking space, the surface of the mirror tilts
slightly. For this to happen, the knob must be in
the position for the front passenger's outside mirror.
You can adjust the tilted mirror surface by turn­ ing the knob in the desired direction . When you
move out of reverse and into another gear, the
new mirror position is stored and assigned to the
key you are using.
The mirror goes back into its original position
once you drive forward faster than 9 mph (15 km/h) or turn the ignition off.
.&, WARNING
Curved mirror surfaces (convex) enlarge the
field of vision. However, they make objects in the mirror appear smaller and further away.
Your may estimate incorrectly when you use
these mirrors to gauge your distance from the
vehicles behind you when changing lanes -ac­
cident risk!
(D Note
- Applies to vehicles with power folding out­
side mirrors*: if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must use the pow­ er folding function to fold the mirror all the
way out. You will hear a loud noise when the
mirrors are latched back in place. The mirror
housing must not be moved back into place
by hand because this would impair the func­
tion of the mirror mechanism.
-

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
-Applies to vehicles without power folding
outside mirrors : if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must
move it back
in p lace by hand.
- If you wash the vehicle in an automatic car
wash, you must fold the exterior m irrors in
to reduce the risk of damage to the mirrors. Never fold power folding exterior m irrors*
by hand . Only fo ld them in and out using
the power controls.
(D Tips
If the power adjustment fails, both mirrors
can be adjusted by hand by pressing on the
edge of the mirror surface.
Dimm ing th e mirrors
Your vehicle is equipped with a manual or auto­
matic* dimming rearview mirror.
F ig . 39 Automatic dimm ing rearv iew mirror•
Manual dimming rear vie w mirror
,..
0 0
> u. a,
~ Pull the lever on the bottom of the mirror back.
Automatic dimming rea rview mirror*
~ Press the b utton @. The indicator light @
tu rns on. The rearview and driver's exterior*
mirrors dim automatically when light shines on
them, for example from headlights on a vehicle
to the rear .
A WARNING 1=
Electrolyte fluid can leak from automatic dim-
ming mirrors if the g lass is broken. Electro­
lyte f luid can irritate skin, eyes and airways .
Lights and Vision
-Repeated or long-term exposure to e lectro­
lyte flu id can lead to irritation of the air­
ways, especially in people with asthma or other respiratory conditions. Take deep
breaths immediately after leav ing the vehi­
cle or, if this is not poss ible, open all of the
doors and windows as wide as possib le.
- If electro lyte fluid enters the eyes, flush
them thoroughly with a large amount of clean water fo r at least 15 minu tes and then
seek med ica l attention.
- If electro lyte fluid comes into contact wi th
the s kin, f lush the affected area with clean
water for at least 15 minutes and then clean
with soap and wate r and seek medical at­
tention. Clean affected clothing and shoes
thorough ly before wearing again .
- If the fluid was swallowed and the person is
conscio us, flush the mo uth wit h water for at
least 15 minutes. Do not induce vomit ing
un less this is recommended by medical pro­
fessionals. Seek medical attention immedi­
ately.
(D Note
If the glass on an automatic dimming mirror
breaks, electro lyte can leak out. This liquid
damages plastic surfaces. C lean this liquid as
quick ly as possible w it h a wet sponge .
@ Tips
-If the light reaching the rearview mirror is
obstructed, the automatic dimming mirror
w ill not function correctly,
- The automatic dimming mirrors do not dim
when the inte rior lighting is turned on or
the reverse gear is selected.
51

Lights and Vision
Sun visors
Fig. 40 Le ft s ide : sun visor
The sun viso rs can be moved out of their brackets
and turned toward the doors@. The sun shade
can also be moved back and forth lengthwise in
this pos ition .
The m irror ligh t switches on when the cover over
the vanity mirror* @opens .
Windshield wipers
Switching windshield wipers on
Fig . 41 Wind sh ield w iper leve r: ope ra tin g the w indshi eld
w ipe r system (ex ampl e: vehicle s w it h ou t rear wi ndow w iper
sy ste m)
Fig . 42 W ind sh ield w iper lev er wit h rear w indow w ip er" :
ope rat ing t he re ar win dow w iper sys te m
Req uirement: the ignition must be switched on.
52
"' N N
~
"'
Move the windshie ld w iper lever to the corre ­
sponding position:
@ -Fron t wipers off
(D -inte rval mode. To increase/decrease the w ip­
er interva ls, move the switch @to the left/r ight .
In vehicles with a light/ra in sensor*, the wipers
turn o n when it is ra ining, whe n the vehicle is s ta ­
tiona ry and the leve r is tapped in the ® position,
o r once the vehicle speed exceeds app roximate ly
2 mph (4 km/h) . The higher the sensit ivity of the
rain sensor is set (switch @to the r ight), the ear­
li er the windsh ie ld wipers react to moisture on
the windshie ld.
@ -slow wiping
@ -fast w iping
@) -sin gle wipe If you hold the lever i n this pos i­
tion longer, the wipers switch from slow wiping
to fast wiping.
® -clean the windshield To e liminate water
droplets afte r switching the winds hield wipe rs
off while dr iv ing, they will operate one more time
severa l seco nds afte r switching them off if t he
temperat ure is above app rox ima tely 39 ° F (4 °C) .
You can swi tch th is func tion off by mov ing the
l ever to posit ion ® within 10 seconds o f the af ­
te rwipe. The afterwipe function is reactivated the
next t ime yo u sw itch the ignition on.
Cl eaning the headlig hts*. The headlight was he r
system * operates only when the low beam head ­
li ghts are on .
If you move the lever in position @,
the headlights will be cleaned in fixed interva ls .
Applies to vehicles wi th rear window w iper:
The rear wiper automa tica lly switches on when
the reverse gea r is engaged and the front wi nd­
shield wipers are on and in ope ra t ion.
@ -Wiping the rea r window* . T he rear w iper
moves abo ut eve ry 6 seconds .
(J)-Cleaning the rear window* . The number of
wipes depends on how long the lever is he ld in
pos ition
(J) .
@ -Rear window wiper* off.

,....,
N
0 > co ,...., A WARNING 1=
- The rain sensor is only intended to assist the
driver . The dr iver is still responsible for
manually switching the w ipers on accord ing
to the v is ibility conditions .
- The windshield may not be treated with wa­ ter-repell ing windsh ield coating agents . Un­
favorable conditions, such as wetness, dark­
ness , or when the su n is low , can cause a
st rong glare, w hich increases t he risk of an
accident. W iper blade chatte r is a lso possi ­
ble.
- Properly f unction ing windsh ield wiper
blades are required fo r a clear view and safe
dr iving
c:> poge 53, Replacing front wind­
shield wiper blades .
CD Note
-If there is frost, make sure t he windshie ld
wiper blades are not frozen to the wind ­
shield. Switching on the windshield wipers
when the blades are frozen to the wind­
shield can damage the wiper blades.
- The windshield wiper system must be
switched off ( lever in pos ition 0) before us­
i ng a car wash . This prevents unintentional
switching on and damage to the w indshield
wipe r system .
- Do not use the wipers to remove ice from
the windows . Us ing windsh ield wipers as ice
scrapers destroys the wiper blades .
(D Tips
-The windshield wipers switch off when the
i gnition is turned off. You can activate the
windsh ield wipers after the ign it ion is
switched back on by moving the winds hield
wipe r lever to any pos it ion.
- Wo rn o r dirty windshield wipe r blades result
i n strea king . This can affec t the ra in sensor
f u nct io n. Check yo ur windshield wipe r
blades regu larly.
- The washe r fluid no zzles in the w indshie ld
washer system are hea ted* at low tempera­
tures when the ignition is on.
Light s and Vision
- When s topping tempo rar ily, such as at a
traffic light, the speed of the windshield
w ipers automatica lly reduces by one level.
- In vehicles with an MMI, yo u can switch the
rain sensor on or off in the
Dri ver assi stance
menu.
Cleaning windshield wiper blades
Clean the w ipe r blades when you see w iper
streaks . Use a soft cloth and a g lass cleaner .
Windshield wiper
.,. Plac e th e windshie ld wiper arms in the servic e
position
c:> page 54 .
.,. Fold the windshie ld wiper arm s away from the
w indshield.
Rear window wiper*
.,. Fold t he windshie ld wiper arm away from the
rear window .
A WARNING
=
Dirty windshie ld w iper blades can impa ir vi-
sion, wh ic h increases the risk of an accident.
CD Note
If you see strea ks again after clean ing the
wiper blades, the blades must be replaced
c:> page 53.
Replacing front windshield wiper blades
Fig. 4 3 Re mov in g windsh ie ld w ip er b la de s
-
.,, ,._
~ a: (0 m
53

Lights and Vision
Wiper service position /blade replacement
po sit ion
.. To bring the wipers into the service position,
turn the ignition
off and move the windshield
wiper lever into position@¢
page 52, fig. 41 .
.. To bring the wipers into the starting pos it ion,
turn the ignition on and move the windsh ield
wipe r lever into position@¢
page 52, fig. 41.
Removing th e wiper blade
.. Fo ld the windshield wiper arm away from the
winds hield.
.. Press the lock ing knob
(D ¢ fig. 43 on the wiper
blade . Hold the w iper blade firmly .
.. Remove the wipe r blade in the direct ion of the
arrow.
Installing th e wiper blade
.. Insert the new wiper b lade into the mount on
the wiper arm @unti l you hea r it latch into
place .
.. Place the w ipe r arm back on t he w indshie ld .
.. Turn the serv ice position off.
_& WARNING
F or safety re asons, t he wind shie ld wiper
blades sho uld be replaced once or twice each
year .
- T he wi ndshield wipe rs mus t only be folded
away w hen in the serv ice posi tion. Other ­
wise, you r is k damaging the paint on the
hood or the windshield wiper motor .
- You should not dr ive your ve hicle or press
the windshie ld wiper lever when the wiper
a rms are fo lded away from the windshield.
The windshield wipers would move back in­
to the ir o rig inal position and could damage
the hood and w indshield.
- To prevent damage to t he windshie ld wash­
er system, a lways loosen wiper blades that
have frozen to the w indshield before turn­
i ng the wipers on .
- To preve nt damage to the wiper b lades, do
not apply gasol ine, pet roleum, thinning
54 agents o
r othe r solvents on the wi per
blades or near them .
- T o prevent damage to the wiper arms or
other components, do not try to move the
windshield wipe rs by hand.
@ Tips
- C ommercial hot wax s uch a s the types used
by car washes make it more diffic ult to
clean the w indshie ld .
- You can also use the service pos it ion, for ex ­
amp le, if you want to protect the winds hield
from icing by using a cover.
- You cannot activate the service posit ion
when the hood is open .
Replacing rear windshield wiper blade
Applies to vehicles: with rear window wiper (A3 Sportback)
Fig.
44 Rear win dow w ipe r: remov ing t he wipe r blade
Removing the wiper blade
.. Fold the w indshie ld w iper arm aw ay from the
rear wi ndow.
.. Ho ld the wiper blade below the center -arrow ­
¢
fig. 44 and pull it o ut of the reta iner. Hold
the windshield wiper a rm secure ly while doing
this.
Installing the w iper blade
.. Press the wipe r blade mount into the re tainer.
Securely hold the w iper arm at the upper p las ­
tic end .
.. Fold the rear window wiper arm back onto the
w indshield. .,..