2016 AUDI A3 Owner´s Manual

,....,
N
0 > co ,...., @ electric motor range or combined total range
@ gasoline engine range
© electric motor range
(D Tips
The values given are based on the latest con­
sumption values.
Plug-in hybrid mode
Applies to vehicles: with plug- in hybrid drive
You can select between one electric mode and
three hybrid modes.
dV Electric mode (EV mode)
EV mode is electric driving only.
EV mode is active at the beginning of every drive
depending on the operating status. The LED in
the
!<=I'! button turns on. The. indicator light al­
so turns on in the instr ument cluster display. The
gasoline engine stays switched off as long as the
battery charge level and climate conditions allow
it .
You can drive with only electric power at speeds
up to approximately 80 mph (130 km/h).
Hybrid modes
The electric motor and the gasoline engine work
efficiently together in every hybrid mode.
OQ!t Hybrid: the battery charge is used as much as
possible when this mode is switched on. This
mode is best suited for long distances.
O\Q!J Hold battery: the high-voltage battery charge
level is conserved as much as possible.
•& Charge battery: the high-voltage battery will
charge if the charge level permits it. This causes
an increase in fuel consumption.
@ Tips
-Applies to "Hold battery" and "Charge bat­
tery": the battery charge level can also de­
crease depending on the driving style.
- If you select the sport driving mode S when
in EV mode, the Hold battery mode is auto­
matically selected. You can select the EV
e-tron
mode again with the 1.:.1•! button
r:!;> page 104.
- if the la• I r:!;> page 104 button is pressed
while in sport driving mode S, the transmis­
sion switches automatically to normal mode
0.
Conditions for electric driving
Applies to vehicles: wit h plug-in hybrid drive
The EV mode can only be switched on if the fol­
lowing conditions are met:
- The cha rge level of the high-voltage battery
must be suff icient.
- The temperatu re of the high-voltage battery
must be adequate (outside temperatures not
below approximately 14°F / -10°C and not
above 104°F / 40°C)
- The speed must not be higher than approxi-
mately 80 mph (130 km/h).
- Kick-down must not be activated.
- The sport drive mode
S must not be selected.
EV mode is switched off if one or more of the
conditions are not met. The gasoline engine will
start automatically. The
E] ind icator light turns
on as a message in the instrument cluster. The
LED in the
l d• I button and the B indicator light
turn off.
Electric drive mode will not continue automati­
cally. Reactivate the EV mode
r:!;> page 104.
(D Tips
It may be necessary for the gasoline engine to
run longer for technical reasons, such as
when condensation accumulates in the en­
gine. Driving exclusively in electric mode is
not possible in this phase.
103

e-tron
Setting plug-in hybrid drive modes
Applies to vehicles: w ith p lug -in hybrid drive
Fig. 90 Center console : but ton &
You can change modes when the vehicle is sta­
tionary or while driving. If the vehicle operating
conditions will not allow you to set the mode manually, the last active mode is se lected .
.,. Press the
laV I button repeatedly until the de­
sired mode is displayed in the instrument clus­
ter . Or :
.,. Select the mode in the MMI
n: press the
I MENU I function button> Car > Systems con­
trol button >
e-tron mode and select the de­
s ir ed mode .
The active mode is displayed the first time the
14 "1
button is pressed .
Plug-in hybrid functions
Applies to veh icles: with p lug -in hybrid drive
The functions described below activate automati­
cally depending on the driving style.
Full acceleration (boost)
The boost funct ion is act ivated by pressing the
accelerator pedal farther down (kick-down). The
l) Not availa ble in a ll Info ta inm en t sy ste m s.
104
vehicle is powered by both the gasoline eng ine
and the e lectric motor when in fu ll acce leration.
Boost is only ava ilable for a short time because it
uses a large amount of energy. Availability de ­
pends on the high-voltage battery charge level.
Coasting
The gasoline engine switches off and disengages
at speeds up to approximate ly 112 mph
(180 km/h) if the acce lerator pedal is not press­
ed and the D position is selected. Driving conser­
vatively like this can reduce fuel consumption .
Energy recovery (recuperation)
When braking, the electric motor will act as a
generator creating electric energy that is then
stored in the high-voltage battery . This also oc­
curs when the vehicle is coasting or driving down­
hill.
If the brakes are applied early and evenly, the electric motor w ill brake the vehicle @
¢page 101 , fig. 88. By doing this , a large
amount of the kinetic energy is recovered and
may be stored as e lectric energy in the high -volt ­
age battery . The conventional brakes are also ac­
tivated when the brakes are pressed very hard.
The strength of recuperation can depend on the
following factors:
- If you are in tiptronic mode
Q page 94 . Or
- If the sport driving mode 5 was selected.
The ene rgy recovery is shown in the energy flow
i ndica tor in the in str ument cluster display
¢page 106 .

,....,
N
0 > co ,...., Tips for an efficient drive mode
Applies to vehicles: with p lug-in hybrid drive
Driving situations
Conditions
-Cautious driving and reserved ac-
ce leration .
Constant driving and -Release the accelerator peda l
c oasting (glid ing)
early and entirely.
-Brake early and evenly with short
Energy recovery (re- pedal movements.
cu peration)
Driv ing in city traffic -
Accelerate moderately and brake
early and evenly
- Intentionally take your foot off of
the gas peda l to allow for Lengthy
coast ing .
Driv ing on highways
-Reduce the vehicle speed by re-
and expressways leasing the accelerator pedal and
not by braking.
- Use the S selector lever position
and tiptronic mode sparing ly.
- Do not run the gasoline engine
while the vehicle is parked to warm
the engine.
- Use the rear window/exterior
Driving in cold weath -mirror defroster and the seat heat-
ing sparingly.
er
-Park the vehicle in a garage over -
night.
e-tron
Vehicle behavior
The kinetic energy of the vehicle is used to
move the vehicle.
The gasoline engine turns
off automati -
cally and disengages when you release the
accelerator pedal comp letely. The veh icle
glides without being propelled .
The electric motor brakes the vehicle. By
doing this, a large amount of the kinetic
energy is recovered and may be stored in
the high-voltage battery in the form of
electric energy .
The kinetic ene rgy of the veh icle is used to
move the vehicle.
The gasoline engine turns
off automati-
cally and disengages when yo u release the
accelerator pedal comp lete ly . T he veh icle
g lid es without being p ropelled .
Fu el cons umption can be reduced by
coasting .
A sporty driv ing style increases fue l con-
sumpt ion.
The temperat ure of the gasoline eng ine
rises very s lowly and the fuel consump-
tion increases considerably .
This conserves the energy in the high-volt-
age battery so that it is availab le to run
the vehicle in electric mode.
This reduces exposure of the high-voltage
battery to cold temperatu res . The re-
quired temperature range for the high-
voltage battery will then be reached more
quickly after you start driving.
105

e-tron
Energy flow indicator
Applies to veh icles: w ith p lug -in hybrid drive
Fig . 91 Instrument cluster: e nergy flow indicator
The energy f low indi cator can be disp layed in the
on-board com puter and in the M MI
1>.
The image is animated in the MMI 1>.
Image in the instrument cluster display
.,. Se lect the On-board compute r tab c> page 29.
Component Color
CD Gasoline engine orange
gray
@ High-voltage battery
Green
Green
(animated i n the
MMI al )
gray
@ motion ar row Gree
n
o range
green-orange
@ mot ion ar row Gree n
@ Disp lay of electric power
availability
•> Not available in a ll Infotainmen t systems .
ll Not available in all Infota inmen t sys tems .
106
Fig. 92 MMI*: energy flow i nd icato r
.,. Select the Ene rgy flow indi cator .
Image in the MMI display1
)
.,. Select in the MMI: I MENU ! button> Car.
Meaning
The gasoline engine is runn ing
The gasoline engine is off High-voltage battery charge level
H ig h-voltage battery is ch arging
Vehicle is not in dr ive ready mode
Elect ric d riving
D riving w ith the gasol ine engine
Driving wit h the gaso line engine and electric mo-
tor (boost)
Recupe ration
Refer to
c> page 107, Electric power availability
display

.... N
0 > CX)
rl I.Cl U"I
Statistics
Applies to vehicles: with plug-in hybrid drive
Fig. 93 Example image: e-tron stat istics
The statistics in the MMI l) show the distances
driven without emissions (electric) and with fuel.
The values are taken from on-board computers 1
and 2 .
Opening the statistics
.. Select: I MENU I function button >Car> Car sys­
tems
> e-tron statistics
.. Turn the control knob to switch between on­
board computer 1 and 2.
Electric power availability display
Applies to vehicles: with plug-in hybrid drive
Fig. 94 Instrument cluster; electric power availability dis­
p lay
The power currently available in the electric drive
system is displayed when you open the energy
flow indicator
r=> page 106.
The bars are filled in with different colors accord­
ing to the power status :
rl
~ 1> Not available in all Infotainment syste ms.
e-tron
@ -white: electric power currently available.
@ -green: electric power currently used .
The more segments that are colored in white in
the E-MAX area
0, the longer the maximum
power can be utilized . The segments turn off in
the E-MAX area when the maximum power can no
longer be utilized.
When the drive power is greatly reduced, the
drive mode will automatically switch to using the
gasoline engine.
The availability of power is generally restricted under the following conditions:
- The temperature of the high-voltage battery is
be very cold or very hot.
- The high-voltage battery charge level is low.
The power availability is not visible if the&] indi­
cator light turns on .
(D Tips
High power availability is necessary, for exam­
ple, when needing to accelerate quickly while
in electric driving mode to pass another vehi­
cle.
Vehicle tool kit and tire mobility kit
Applies to vehicles: with plug-in hybrid drive
Fig. 95 Luggage compartment: vehicle tool kit and tire
mo bility kit
The vehicle tool kit and the tire mobility kit (Tire
Mobility System) are located in the side trim pan-
el @ and @ in the luggage compartment. .,.
107

e-tron
Additional information about the vehicle tool kit may be found under
c::, page 280 and informa­
tion about the tire mobility kit under
c:> poge281 .
(D Tips
The vehicle must not be operated without the
tire repair set.
Vehicle transport
Applies to veh icles: w ith plug- in hybrid drive
The following contains information you should
know about transporting your vehicle.
The MQB-A lithium-ion battery system equipped
in your vehicle is composed of SANYO 12 U F 261
591 type batteries and has it passed test 38.3 in
accordance with the UN Tests and Criteria hand­ book. The vehicle may be transported with the
battery installed as conventional class 9 hazard­
ous materials without additional offic ial consent
for air and sea transportation (current law ICAO­
TI and IMDG-Code 01.01.2012) .
Jump starting and 12 volt battery
Applies to veh icles: with plug -in hybrid drive
Fig. 96 Engine compartment: connectors for a charger and
j ump start cables
The vehicle is equipped with one 12 vo lt battery
and one high-voltage battery.
If the 12 volt battery is drained, it can be charged
with a charger or you can jump start the vehicle
using another vehicle battery in the same way as
a conventional vehicle .
Note the information on charging the battery
¢
page 249 and for jump starting the vehicle
c:>poge297 .
108
.,. Open the hood¢ page 23 7.
.,. Remove the fuse box cover @ to access the
positive terminal
0 c::> page 239.
.,. Clamp the terminal clamps from the charging
device or jump start cable to the positive termi­
nal
0 and to the body ground point 0-
(D Note
You must not give a jump start with your vehi­
cle. This could cause s ignificant damage to
the electrical system in your veh icle.
Coolant
App lies to vehicles: with plug-in hybrid drive
Fig. 97 Engine compartme nt: coolant expa nsion tank
Your vehicle has two coolant expansion tanks
that are separate from each other:
@ : expansion tank for gasoline engine and elec­
tric motor.
@ : expansion tank for the high-voltage area .
The expansion tank@ must not be opened
c:>&_ .
.,. Switch the ignition off .
.,. Open the hood
c:> poge 237.
...
.,. Always check the coolant level in both coolant
expansion tanks @ and @ using the outer
markings.
.,. When you fill coolant in the expansion tank@,
please refer to
c::> page 244, Cooling system.
.,. Do not drive any farther if the expansion tank
@ is missing coolant. Contact an authorized
Audi dealer or authorized Audi Service Facility immediately ¢&_ . ..,.

,....,
N
0 > CX) ,....,
I.Cl U"I ,....,
I.Cl ,....,
,&_ WARNING
-Read and follow t he warn ings in
¢ page 236, Working in the engine com­
partment
before open ing the hood and
check ing t he coolant level.
- The expansion tank @ may only be opened
and filled by an a uthorized Aud i dea ler or
authorized Aud i Service Fac ility.
- Coo la nt can enter the inside of the battery
when f illing the expansion tank @ and
cause a short c ircuit, which inc reases the
risk of fi re .
Refueling
Opening the fuel filler flap
Appl ies to vehicles: with plug- in hybrid drive
Fig. 9 8 Driver 's doo r: button il
The ta nk sys tem must be ve nted be for e refueling
.. Pull on the
Iii switch.
.. The fue l filler door automatically opens w ith in
a few seconds afte r vent ing .
Read and fo llow the directions for inserting the
f u el pump noz zle
¢ page 109.
Read and fo llow the inst ruct io ns for refueling
¢ page 230.
e-tron
Inserting the fuel pump nozzle
Applies to vehicles: with plug- in hybrid
Fig . 99 Fue ling proce du re : in ser t the fuel pump nozzle co r­
r ect ly
M ake s ure w hen inse rting the f uel pu mp noz zle
t h at you do no t press o n the fuel filler door open ­
er (!) with the fue l pum p nozzle . See the labe l in
the f ue l fi ller door @. Otherwise, a va lve wi ll lock
in the fue l filler neck and stop the fueling , even if
t h e tank is not full. You must vent the tank sys­
tem again if yo u press on the fuel fille r doo r
opener. The f uel p ump nozzle can stay in the fue l
filler neck when doing this.
Vent the tank system by pulling the
Iii switch in
the d river's door
¢ page 109.
Driver messages
Applies to vehicles: with plug-in hybrid drive
ti Tank flap open . Please press button again
for fueling
Fueling is possib le for a certain amou nt of time
after press ing the
Iii button . Yo u m ust press the
Iii button again if th is time is exceeded .
ti Tank flap malfunction! Unlock tank flap
manually . See owner's manual
T he re is a ma lfunction. Yo u must man ually un­
lock the fue l fi ller door
¢ page 110.
ti Warning! Limited power
The fue l ta nk is almos t emp ty . You must ant ici­
p at e a sign ifi can t power loss. Drive i mmed iate ly
t o a ga s st at ion .
POWER LIMIT Warning! Limited power
109

e-tron
The gasoline engine is no longer available be­
cause there is not enough fuel. Drive immediately
to a gas station.
Fuel filler door emergency release
A pp lies to ve hicles: w ith plug- in hy brid drive
You must use the emergency release to open the
fuel filler door when there is a malfunction
c::> page232 .
The tank is not vented. You can only fill a small
amount of fuel in the tank.
~ Fill only until the automatic fuel pump nozzle
turns off for the first time when it is operated
correctly.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
(D Tips
Pressure can escape if you open the tank cap
after using the emergency release. This can
create noises.
Charging
General information
A pp lies to veh icles: w ith plug -in hybrid drive
Two options are available for charging the vehi­
cle:
- Charge at a public charging station with a spe­
cial charging cable*
c::>page 112.
- Charge with household and industrial power
sockets using the Audi e-tron charging system
c::> page 112.
Environmental conditions when using the
charging system
-Operating temperature : -13 °F (-25 °C) to 95 °F
(+35 °C)
- Humidity:
5% to 95%, non-condensing
- 13,000 feet (4,000 meters) maximum above
sea level
110
Warnings when using the charging system
£
Surfaces can become very hot when
in direct sunlight.
&~
Incorrect use increases the risk of
electric shock.
~"-
Do not use any extensions cords or
cable reels.
~
Do not use any travel adapters.
~~
Do not use any power strips.
~~~
Do not use any charging cables with
damage to the electronics or the
connecting wires.
.&_ WARNING
-
Sockets that are installed incorrectly can
cause electric shock or fire when charging the
high-voltage battery using the vehicle charg ­
ing connection.
- Installation and setup of the household con­
nection for the Audi e-tron charging system
may only be performed by a qualified elec­
trician. The qualified electrician is thereby
fully responsible for adhering to applicable
standards and regulations.
- Make sure that the selected charging con­ nection is suitable for drawing 16 amps .
- Make sure that the
110 volt socket is
grounded and shielded from water.
- Always check the fuse for the GFI outlet be­
fore connecting the charge cable.
- Never use a damaged GFI outlet.
- Read and follow the safety precautions in
the Audi charging dock* assembly instruc­
tions.
.&_ WARNING
If you are not familiar with the socket or the
e lectrical installation or it has not been
checked by qualified experts, never use it for
charging. Even very low charging currents can
cause ser ious damage and in particular fires if
the socket or electrical installation is in bad
condition. If necessary, get expert assistance
~