2016 AUDI A3 Owner´s Manual

,....,
N
0 > co ,...., e-tron
Symbol Error code LED on the control
unit@ Meaning
Solution
480 Red
110 Red
Vehicle: charging unit
LED on the vehicle @
On
pulsating light
Green
Blinks for approxi-
mate ly one min ute
after leaving the vehi-
cle
On
Yellow
Flashes
On
Red
Flashes Flashes
Error in the control unit D
isconnect the control
unit from the power sup­
ply and reconnect it.
Flashes Ground fault interrupter
(G FI) triggered in the con ­
tra l unit . Reset the ground fault in­
terrupter with the
IOKI @
button r=>page 115,
fig. 106 .
Have the electri­
cal installation checked by
a qualified electrician if
the same d isplay appears .
Meaning Solution
High-voltage battery charging Remove
the charger, put the cap
on and close the cover on the
process is completed .
charging unit.
The high-voltage battery is charg-
ing or the vehicle is being a ir con-
ditioned/heated.
Charging timer was programmed
but the charging process has not
started yet . The LED in the button
@ r=>page 115, fig . 107 also
turns on.
Have the power supply or power
supply system inspected. Check
No power supply was recognized the status display on the control
even though the charging cable is unit
r=> table on page 118 . See an
plugged in . authorized Audi dealer or author-
ized Audi Service Facility for ass is-
tance if necessary.
The se lector lever in not in the P Move the selector lever into the P
position. position.
Check if the charging connector is
inserted correct ly
r=> page 116. Re-
The charging connector cou ld not move the charging connector and
be correctly locked in the vehicle
insert it into the charging port
charging port . again. See an authorized Audi
dealer or authorized Audi Service
Facility for assistance if necessary .
Error in charging system . The See an authorized Audi dealer or
high-voltage battery cannot be authorized Audi Service Facility for
charged. assistance if necessary.
119

e-tron
Charging times
Applies to vehicles: w ith plug-in hybrid drive
The length of the charg ing process using the Audi
e-tron charging system can vary based on the fol­
lowing factors:
- Sockets be ing used (household or industrial
sockets).
- System voltage and current strength specific to
a country.
- The value set for the charg ing power level on
the control unit (SO% or 100%) .
- Fluctuations in the system voltage .
- Temperature outside the vehicle.
- Temperature of the high-voltage battery .
- Adjustments to the climate control inside the
vehicle.
- Current capacity of the charging connector.
Examples of charging times
Connection Charging time for
100% charge
Household socket approximately 10
(100 V, 10 A)
hours
Household socket approximately 8 .2
(110 V, 10 A) hours
Household socket approximately 5.2
(220 V, 8 A) hours
Household socket app roximately 3 .8
(230 V, 10 A) hours
Industrial socket (200 V, approximately 2 .3
16 A) hours
Industrial socket (220 V,
approximately 2.3
16 A) hours
Industrial socket (230 V, approximately 2 .3
16 A)
hours
Industrial socket (240 V, approximately 2.3 16 A) hours
(D Tips
-Multiple versions of charging cables are of­
fered due to the different power supply sys­
tems in different countries. The maximum
charging power may potentially be unavaila­
ble because of this. Contact an author ized
120
Audi dealer or authorized Audi Service Fa­
cility for more information.
- Th e charging times may be longer in ex­
tremely high or low temperatures .
Audi e-tron charging system PIN
Applies to vehicles: with plug-in hyb rid drive
The control unit can be locked by entering a 4 -
digit PIN of your choice. If a PIN is activated, the
selected PIN must be entered before every use.
We recommend locking your control unit to pro­
tect it aga inst unauthorized access by a third par­
ty.
Activating the PIN
.. Press the I OK !@ ¢ page 115, fig. 106 button
on the control unit.
POWER and SET PIN ap­
pear in the disp lay fie ld .
.. Select
SET PIN using the arrow button ©-
.. Press the IOKI button @.
ENTER PIN appears in
the display field .
.. Select the desired value by pressing the arrow
buttons © up or down .
.. Use the r ight arrow button © to go to the next
dig it.
.. Press the left arrow button© to go to the pre-
vious menu.
.. Enter all of the digits.
.. Press the IOKI button @after the last digit.
.. REPEAT PIN appears on the display field .
.. Enter the PIN again using the arrow buttons
©-
.. Press thelOK l@ button .
.. PIN OK appears in the display field if both en-
tries match .
.. The PIN is now activated.
Deactivating the PIN
Requirement: the control unit must be unlocked.
.. Enter the numerical code
0000. Proceed as if
you were activating the PIN¢
page 120.
.. The PIN is deactivated.
Locking the control unit
Requirement: the PIN must be activated.

.. Press the~ button @ r::?vpage 115, fig. 106 on
the control unit.
Unlocking the control unit
Requirement: the P IN must be activated.
.. Press any button on the control unit.
.,. PIN? appears on the display field .
.. Enter the PIN .
.. Press the
IOKI button @.
{O) Tips
-The PIN is deactivated in the factory default
settings.
- If you do not remember your PIN, contact
an authorized Audi dea ler or authorized
Audi Service Fac ility.
- If the first PIN entry differs from the second
ent ry, the first PIN entry is displayed.
- If nothing is entered w ith in 20 seconds of
th is, the set value is not changed.
Indicator Lights and
messages
Applies to vehicles: with plug-in hybrid drive
If the B indicator light turns on, the high-volt­
age battery is charging or is already completely
charged.
I f the . indicator light stays on, there is a mal­
function in the charging system. Have the prob­ l em corrected immediately by an authorized Audi
dea ler or authorized Audi Service Facility.
l'I Charging connector still attached. Driving
not possible
This message appears when the charg ing system
is sti ll connected to the veh icle. Remove the con­
nector
r::?v page 117, After charging.
1,1 AC charging: currently not possible
This message appears when the charging system
is incompatible. Only charge using the charging
system that is designed for your vehicle.
;::: 1,1 AC charging : system fault! Plea se contact 0
iii Service
e-tron
This message appears if there is a malfunction in
the charging system. Have the prob lem corrected
immediately by an authorized Audi dealer or au­
thori zed Audi Service Facility .
Vehicle charging
connector emergency
release
Applies to vehicles: with plug -in hybrid drive
There could be a malfunction if you are not able
to pull the vehicle charging connector out of the
vehicle charging port. You must use the emer­
gency release to release the vehicle charging con­
nector.
Requirement: the se lector lever must be in the P
position, the vehicle must be unlocked and the
charging process must have been ended or inter­
rupted.
.,. Press and hold the immediate charging button
@ r::?vpage 115, fig . 107 .
.. Press the [@l button on the remote control key
at the same time.
.. Remove the connector.
.. Drive to an authorized Audi dealer or author­
ized Audi Service Facility immediately to have
the malfunction corrected .
If the charging connector still cannot be removed
after using the emergency release, see an author­
ized Audi dealer or authorized Audi Service Facili -
ty for assistance .
Charging unit cover
emergency release
Applies to vehicles: with plug-in hybrid drive
~ Fig. 111 Front of the vehicle: cover emergency release U"I
121

e-tron
You can release cover using the emergency re­
lease.
.,. Turn the lock to the horizontal position .
.,. Unlock the veh icle.
.,. Open the hood
r:!;> page 23 7, Opening the hood .
.,. Carefully pull on the knob @until there is re-
s istance .
.,. Turn the lock to the vertical position
r:!;> page 115, fig . 108 .
.,. Slide the cover carefully to the side if necessa­
ry .
Climate control
Description
Applies to vehicles: with plug- in hybrid drive
Your vehicle has either auxiliary heating or auxili­
ary heat ing/ air conditioning*.
The auxiliary heating or the auxi liary heating/ air
conditioning* switches on depending on the out­
side temperature and the temperature set on the
climate control unit .
Switching on/off immediately
.,. You can switch the climate control on and off
immediately in the MMI*
¢page 123. Or
.,. Switch off the blower with the~ button
¢ page 72, fig. 72.
Setting the timer
.,. You can set the time when your vehicle should
reach the desired temperature. Your set tem­
perature and the outside temperature deter­
mine when the climate control switches on.
@ Tips
- The temperature that the climate control
system adjusts to depends on the last tem­
perature you set in the climate control unit
c;;,page 72.
-The climate control system does not auto­
matically switch on or off earlier if the vehi­
cle battery charge or the fuel level is too low.
122
· Auxiliary climate control
Applies to vehicles: with plug-in hybrid drive without auxiliary
hea ting
The aux iliary climate control controls the tem­
perature in the vehicle inter ior ent irely with elec­
tric power. It turns on only if the high-voltage
battery charge level is sufficient and there is
enough fuel in the tank.
Auxiliary heating / air conditioning
Applies to vehicles: with plug-in hybrid drive and auxiliary
heat ing
The aux iliary heating/ air conditioning controls
the temperature in the vehicle interior if the
high-voltage battery charge level is suff icient and
there is eno ugh fuel in the tank.
The
.ill. symbo l blinks in the climate contro l unit
whe n auxiliary heating is switched on.
When the auxiliary heating/ air conditioning t im­
er is programmed, the Ill symbol stays turned on
until the departure t ime is reached.
& WARNING
- To reduce the risk of poisoning, the auxiliary
heating/ air conditioning must not run in
confined spaces .
- To redu ce the risk of fires, the auxiliary
heating/ air conditioning must not run
when refueling.
- Due to the high temperatures that result
from operating the auxiliary heating/ air
conditioning, the vehicle must be parked in
a way so that the hot exhaust can escape at
the bottom of the engine cover without ob­
struction. The exhaust must not come into
direct contact with highly flammab le mate­
r ials.
(D Tips
Water vapor can build up near the engine
compartment when outside temperatures are low. This is a natural phenomenon and is no
cause for concern.

Switching on/off immediately in the MMI1l
Applies to vehicles: with p lug- in hybrid drive
Bordbuch~
Standheizung / -k llmatlslerun g ~
Standheizung/ -k limat isierung einschalten
Timer 1: So 10 .11. 0:00
D
Timer p rog rammie ren •
Car Systeme
Fig. 112 MMI example: sw itching t he auxilia ry heat ing/
air co ndit io nin g• o n/off immediate ly
Switching the auxiliary climate control on/
off:
.,. Se lect the I MENU I button > Car> Car Systems >
Aux. climate control
> Turn on auxiliary cli­
mate control or Turn off auxiliary climate con­
trol.
Switching the auxiliary heating / air
conditioning* on/off:
• Sel ect th e I MENU
I bu tto n > Car > Car Systems >
Auxiliary heating / air conditioning
> Turn on
auxiliary heating / air conditioning or Turn off
auxiliary heating/ air conditioning .
(D Tips
T he au xili ary cl imate contro l or the aux iliary
he ating / air cond itioni ng* ca n als o be sw itch ­
ed on a nd off i mmedi ately w hen a tim er is
se t.
,....,
N
0 > co ,...., :=: l) Not avai lab le in all In fota inment system s.
e-tron
Setting the timer in the MMI1l
Applies to vehicles: wit h pl ug-in hybr id drive
Fig. 1 13 MM I: set tin g t he tim er
B y se ttin g th e de parture time, you de ter mine
whe n your veh icle should re ach the des ire d t em ­
peratu re. You can set
a ti me r using the aux iliary
cl imate control o r a uxiliary heat ing/ air condi­
tion ing * menu.
Auxiliary climate control: setting the timer • Sele ct: !ME NUI button> Car> Car Systems >
Aux . climate control > Program timer > Timer
1: Departure time .
• Set the t ime and the date .
• Press the
I BACK! button .
• Confi rm the setting with the cont rol knob to ac­
tivate the time r. A ./
¢ page 123, fig . 112 ap­
pea rs in the box .
Auxiliary heating / air conditioning* : setting
the timer
• Select: !M EN UI button> Car> Car Systems >
Auxiliary heating/ air conditioning
> Program
timer > Timer 1: Departure time .
• Se t the t ime and the da te .
• Press the
I BACK I button.
• Confir m the settin g wit h th e co ntro l kn ob to ac­
t iv at e the time r. A ./
¢page 12 3, fig . 11 2 ap ­
pea rs in the box .
A ft er the depa rtur e tim e is reac he d, t he nex t cal ­
end ar d ay is au tom atic ally en te red in th e
MMI.
To activate the a uxiliary climate cont rol or auxi li­
ary heating/ ai r con ditionin g* for t he next day,
co nfirm the sett ing( ./ in the
MMI ¢ page 123,
fig. 112). ..
123

e-tron
(D Tips
-You can set the timer a maximum of 7 days
in advance.
- You can operate the climate control in the
vehicle interior when the high-voltage bat­
tery is charging using the charging timer
c>page 116.
-Make sure the time and date match in the
MMI settings so that the timer can function
properly. Refer to the MMI Operating Man­
ual for setting the date and time.
- The auxiliary heating or auxiliary heating/
air conditioning* can run longer after the
departure time is reached.
Audi connect e-tron
services
General information
A pp lies to ve hicles : w ith plug- in hy brid drive
With Audi connect e-tron services l), you can ac­
cess various information or control individual
functions remotely using mobile devices (such as
a smartphone) or a web portal.
To use Audi connect e-tron services
l), please
note the following:
- You will need to register for Audi connect e­
tron services at
myaudiconnect .com. You can
access and manage e-tron services and features
at
etron.audiusa.com. If you need assistance
with your Audi A3 e-tron EV services, you can
contact customer service at 844-573-8766.
- Your mobile devices must be compatible.
A WARNING
Read and follow the safety precautions in
your MMI Operating Manual.
l) Wireless serv ice is provided by a thir d- part y provider.
-
Please contact your dea le r or call 877 -505 -2834 for more
informat ion about your carrier. Co nnected dev ices may
not be 4G -capab le. Full speeds avai lable but may be
slowed due to excessive usage, locatio n, coverage and
othe r factors. Coverage not available everyw here . See cov­
erage map for your Audi co nnect data carrier for more in­
format ion.
124
· Vehicle data
App lies to vehicles : wi th plug-i n hybrid drive
The Dr iver Information System collects data un­
der certain conditions and sends it to a server.
When data is stored, you can data such as the ex­
amples listed below using the Audi connect e­
tron services:
- Duration of the drive in hours and minutes,
- average speed driven in mph (km/h),
- distance driven in miles (km),
- average electric consumption .
For additional information on the Driver Informa­
tion System, refer to
c> page 28, Driver informa­
tion system.
Doors and lights
App lies to v ehicl es: wi th plug-in hybrid drive
You can access and display the current status of
the following vehicle data on your mobile devices
without having to be inside the vehicle.
- If the vehicle doors and lids are open/closed,
- If the parking l ights are on/off.
For additional information on opening and clos­
i ng the doors or for the vehicle light ing, refer to
c> page 3 5, Opening and closing or to c> page 46,
Exterior lighting.
(D Tips
-If the high-voltage battery is not charged,
the amount of access requests is limited to
15 after switching off the ignition. This
helps conserve the 12 volt vehicle battery.
You cannot contro l functions or access in­
formation if the charge level of the 12 volt
vehicle battery is too low.
- If at least two minutes have passed after
the last time the ignition was switched off,

,....,
N
0 > co ,...., you can reset the access counter back to "0"
as needed after switching the ignition on/
off again.
Vehicle status
Applies to vehicles: with plug- in hybrid drive
You can access various vehicle statuses using the
services, such as:
- high-voltage battery charge level,
- electric range,
- mileage,
- next inspection.
For addit ional information, refer to¢
page 101,
Power meter overview
and ¢ page 102, Range
display.
A WARNING
Do not be misled by the status report displays
by ignor ing messages and/or illuminated
warning and indicator lights in the vehicle.
This could lead to break downs in on the road,
accidents and serious injuries.
@ Tips
- If the high-voltage battery is not charged,
the amount of access requests is limited to
15 after switching off the ignition. This
helps conserve the 12 volt vehicle battery.
You cannot control functions or access in­
formation if the charge level of the 12 volt
vehicle battery is too low.
- If at least two minutes have passed after
the last time the ign ition was switched off,
you can reset the access counter back to "0"
as needed after switching the ignition on/
off again .
Vehicle position
Applies to vehicles: with plug -in hybrid drive
The vehicle collects data under certa in conditions
and sends it to a server.
When data is stored, you can data such as the ex­
amples listed below using the Audi connect e­
tron services:
- Vehicle location display
e-tron
-Display of one's own location
- Route to your vehicle
If your mob ile dev ice also has a navigation func­
tion, you can nav igate to your last known parking
location .
For example, you have the option to show the
route to your vehicle and to send the correspond­
i ng locations.
(D Tips
- The new parking locat ion cannot be deter­
m ined with this service if the vehicle is
moved after shutting the vehicle off and
w ithout switching the ignition on and off
again, for example when being towed or if
the vehicle is stolen .
-If the vehicle is moved and shut off again
using the second key, for example, the new
park position is transmitted to the
server af­
ter removing the key.
Charging
Applies to vehicles: with plug- in hybrid drive
You can contro l and access the high-voltage bat­
tery ch arging process remotely using these
serv­
ices. You have the following options:
- check the battery charge level,
- start/end the charging process,
- program the charging t imer with/without cl i-
mate control,
- deactivate/activate the charging timer.
For additional information, refer to¢
page 112,
Charging the battery with the Audi e-tron charg­
ing system.
A WARNING
Only perform charging functions on the high­
voltage battery if the vehicle is shut off cor­
rectly, is connected to a suitable socket and if
the ignition is switched off.
125

e-tron
Climate control
Applies to vehicles: with plug-in hybrid drive
You can control the climate control in your vehi­
cle remotely using these services:
- start/end climate control,
- program the timer,
- deactivate/activate the timer.
For additional information, refer to
~ page 122,
Climate control.
A WARNING
Only perform the climate control functions if
your vehicle is shut off correctly and the igni­
tion is switched off.
126