2016 AUDI A3 Owner´s Manual

,....,
N
0 > co ,...., immediately contact your authorized Audi
dealer or qualified workshop to have all
brake pads checked or replaced if necessary.
·~ Hill hold
Hill hold assist: unavailable
If thell indicator light turns on and this mes­
sage appears, hill hold is not available.
II Manual control!
If th is message appea rs, press the brake pedal.
Continue driving w ith the help of the park ing
brake . ¢
page 85
EPC Engine control (gasoline engine)
Applies to vehicles: with gaso line engine
I f the 13:B indicator light turns on if there is a
malfunction in the engine control.
Drive slowly to an author ized Audi dealer or au­
thor ized Audi Service Facility to have the eng ine
checked .
If the
13:B indicator light turns on when you start
the eng ine, there is an automatic start malfunc­
tion . To start the engine, follow these steps :
- Vehicles with ignition lock¢
page 80, Auto-
matic start malfunction
- Vehicles with a convenience key¢ page 83,
Automatic start malfunction.
W Engine control (diesel engine)
Applies to vehicles: with diesel engine
The engine is preheating if the II indicator light
turns on when the ign ition is switched on.
If the indicator light blinks whi le driving, there is
a ma lfunction in the engine control.
Drive slow ly to an authorized Audi dealer or au­
thorized Audi Service Facility to have the ma l­
function corrected.
If the
II indicator light turns on when you start
the engine, there is an automatic start ma lf u nc­
tion. To start the engine, proceed as follows :
Instruments and indicator lights
vehicles with ignition lock ¢ page 80; vehicles
with convenience key
¢ page 83.
o System indicator light (MIL)
The system indicator light (MIL) is part of the On
Board D iagnost ic system (OBD II). Tht>
¢.,, c;ym­
bol turns on when the ignition is switched on and
turns off again once the engine is started and
running at a steady idle speed . This indicates that
the MIL is functioning correct ly.
The ind icator light turns on if there is a malfunc­
t ion in the engine electronics. See an author ized
Audi dealer or authorized Audi Service Fac il ity to
have t he malfunction corrected .
The system indicator light (MIL) may turn on if
the fuel filler cap is not closed correctly
¢ page 230.
For additional information, refer to¢ page 26.
.m,, Diesel particulate filter
Applies to vehicles: with diese l eng ine and diese l particulate
filter
II Particulate filter: system fault! See owner's
manual
T he diese l particu late filter requires regenera­
tion . To support the filter's self-cleaning func­
t ion:
Drive for approximately 15 minutes at
40 mph
(60 km/h) or above in the S selector lever posi­
tion . Keep the engine speed around
2,000 RPM .
The temperature increase that will result from
th is can burn off the soot in the fi lter. The indica­
tor light will turn off when the cleaning has com­ pleted successfully .
If the indicator light does
not turn off, drive im­
med iate ly to an authorized Audi dealer or author­
ized Audi Service Facility to have the malfunct ion
corrected .
A WARNING
Always adapt your speed to the current
weather, road and traffic condit ions. You
should neve r disobey traffic laws in order to
fo llow driving recommendations.
23

Instruments and indicator lights
(D Tips
For additional information on the diesel par­
ticulate filter, refer to¢
page 233.
!?) Engine speed limitation
A pp lies to ve hicles : w ith e ngin e spee d limit ation
[II Max. engine speed: XXXX rpm
The engine speed is automatically limited to the
speed displayed in the driver information system.
This protects the engine from overheating.
The engine speed limitation deactivates once the
engine is no longer in the critical temperature
range and you have released the accelerator ped­
al once.
If the engine speed limitation was activated by
an engine control malfunction, the
[m indicator
light also turns on. Make sure the engine speed
does not go above the speed displayed, for exam­
ple when downshifting. Drive to an authorized
Audi dealer or authorized Audi Service Facility im­
mediately to have the malfunction corrected.
~ Engine oil level (min .)
II Check oil level
You may continue driving for the time being.
Check the engine oil level as soon as possible
¢page 240.
-If the engine oil level is too low, add engine oil
qpage242.
- If the engine oil level is correct and the indica­
tor light still turns on, drive at low engine
speed to an authorized Audi dealer or author­
ized Audi Service Facility.
'1::7' .., Engine oil sensor
• Oil level sensor: system fault!
The sensor to check the engine oil level has
failed. Drive to an authorized Audi dealer or au­
thorized Audi Service Facility immediately to have
the malfunction corrected.
Ill Oil level sens.: oil change necessary. Please
contact Service
24
The engine oil level is too high.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected .
(D Note
Refer to the description in the Owner's Man­
ual
q page 242, Checking the engine oil level
and ¢ page 242, Adding engine oil 5) Tank system
ID Please refuel
If the indicator light turns first turns on and this
message appears, the tank contains the follow­
ing amount of fuel:
- Front wheel drive: approximately 1.8 gallons (7
liters)
-All wheel drive: approximately
2.2 gallons (8.5
liters)
fiD Please refuel immediately
If the indicator light turns on the message ap­
pears, the fuel tank is almost empty. Refuel the
vehicle immediately.
ID Fuel tank malfunction! Please contact Serv­
ice
If the indicator light turns on and the message
appears:
- there is a malfunction in the fuel tank system,
or
- in vehicles with diesel engines, water may have
collected in the fuel filter.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.

(D Note
Applies to veh icles w ith a diesel engine: if the
diese l fuel quality is poo r, it may be necessa ry
to have the water drained from the water sep­
arator
1 ) in the fuel filter more often t han
specif ied in the ma intenance schedule. This
can help red uce eng ine malfu nctions .
@I For the sake of the environment
Fuel should never enter the sewe r system or
come into contact w ith the ground.
@ Tips
More informat ion on ref ueling is ava ilable on
page
c:> page 230.
~ Washer fluid level
m Please add washer fluid
F ill the washer fluid for the w indshield washer
system and the headlight washer system* when
the ignition is switc hed off
c:> page 251 .
O Windshield wipers
m Windshield wiper: system fault!
There is a malfunction with the windshie ld w ip­
ers.
D rive to an autho rize d Aud i dea le r or a uth orized
Aud i Service Faci lity immediately to have the
malfunct ion corrected.
~ Defective light bulb warning
App lies to vehicles: with driver information system
If th e S:I indicato r light turns on, a b ulb has
fa iled . The message ind icates the loca tion of th e
bu lb.
Replace the bulb immediately.
Vehicle lights: system fault!
There is a malfunction in the he adlights or the
,...., ligh t swit ch . D rive to an a utho riz ed Audi d ealer o r
N
0 > co ,...., :;;: 1) Thi s fun ctio n is not a vai lab le in all c oun tries. ,....,
Instruments and ind icator lights
a uthori ze d Aud i Serv ice Facility immedia tely to
have t he malfunction cor rected.
A WARNING
-- Light bulbs a re under pressure an d can e x-
p lode when b ulbs are replaced, w hich in­
creases the risk of injury.
- W ith gas -discharge lamps * (xenon head­
lights), the h igh-vo ltage component must
be ha ndled approp riately. Ot he rwise, there
is a risk of fatal injury.
-
i,0 Dynamic Headlight range control system
Applies to vehicles: with Xenon lights
11 Headlight range control: system fault!
The re is a ma lf u nction in the dynam ic head light
r ange control system, which may cause g la re for
other drivers.
D rive to an authorized A udi dealer or authorized
Audi Se rvice Facility immed iate ly to have the
malfunction corrected.
~O Audi adaptive light
Applies to vehicles: with Audi adaptive light
IIJ Audi adaptive light: system fault!
The re is a ma lf u nction in the adaptive lights. The
headlights st ill function.
Drive to an authorized A udi dealer or autho rized
Audi Se rvice Facility immed iate ly to have the
malfunction corrected.
@P Light/rain sensor
Applies to vehicles: wit h light/ra in sensor
El Automatic headlights: system fault!
El Automatic wipers : system fault!
T he light/ rain sensor i s m alfunctioning.
T he low beams remai n sw itched on a t all times
fo r sa fe ty reasons when the ligh t swi tch is in t he
AUTO p os ition. Yo u can cont in u e to tu rn t he
li gh ts on and off using t he lig ht sw itch . You can ..,.
25

Instrumen ts and ind icator ligh ts
still control all wiper functions that are
independent of the rain sensor.
Drive to an a uthorized Aud i dea ler or authorized
Aud i Serv ice Facility immediately to have the
malfunction corrected .
; Adaptive dampers
Applies to vehicles: with Audi drive select
R Suspen sion : sys tem f ault!
There is an adaptive damper ma lf u nction.
Drive to an authorized Aud i dealer or authorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
¢¢ Turn signals
I f the . or
DI indicator ligh t bl inks, a turn s ig­
na l is turned on. If both i ndicator lights are blink­
i n g, the emergency flashers are on .
I n an indicato r light blinks twice as fast as usua l
then a blinker bulb has failed. Care fully drive to
an author ized Audi dealer or authorized Audi
Serv ice Facility immediately to have the malfunc­
tion corrected.
(D Tips
For more information on the turn signals, re­
fe r to~
page 48.
On-Board Diagnostic
system (OBD)
System indicator light (MIL)
The system indicator light (M IL)
¢4 in the instru­
ment cluster is part of the On Board Diagnostic
System (080 II).
The warning/indicator light turns on when the ig­ nition is switched on and turns off once the en­
gine is started and is running in id le at a stable
speed. This indicates that the MIL is functioning
correctly.
If the light doe s not turn off after starting th e
engine or turns on whi le driving, this may indi­
cate there is a malfunct ion in the engine. If the
26
indicator tu rns on, the cata lytic conve rter may be
damaged.
D rive with reduced engine performan ce (avoid
high speeds for extended per iods of t ime and/o r
fast acceleration) and have the ma lfunction cor ­
rected. See an authorized Audi dealer or author­
i zed Audi Service Facility .
The ind icator may turn on if the e lectro nic speed
li miter is faulty . For add itiona l information, refer
to
c::> page 130, Electronic speed limiter.
The MIL may a lso turn on if the fuel filler cap is
not clo sed corre ctly
c::> page 230.
On-Board Diagnostics
F ig. 7 Locat ion of Data Link Connector (DLC)
On-Board Diagnostics mon itors the components
of your emission con trol system. Each monitored
component in your engine system has been as­
s igned a code . In case o f a malfunction, the com­
ponent will be identified and the fault stored as a
code in the contro l module memory.
The M IL light m ay also illum inate if there is a
l eak in the on -boa rd fuel vapor recovery sys tem .
If the light illuminates after a refuelling, stop
the veh icle and make sure the fuel filler cap is
properly closed
c::> page 230.
In orde r to make an accu rate diagnosis, the s to r­
ed data can only be d isplayed using special d iag­
nostic equipment (generic scan tool for 080) .
In orde r to co nnect the special d iagnost ic equ ip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the r ight of the hood
release
c::> fig. 7. II>

,....,
N
0 > co ,...., Your authorized Audi dealer or a qualified service
station can interpret the code and perform the
necessary repair.
A WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­ tions, which can increase the risk of a colli­
sion!
-
Instruments and indicator lights
27

Driver information system
Driver information
system
Overview
A pp lies to veh icles: w ith driver information system
F ig. 8 In strum ent cluster: Drive r Info rmation System (ex­
amp le)
Data is automatically recorded, processed and
d isplayed in the driver information system . Set­
tings for special equipment can be adjusted in
the MMI. Se lect the
I MENU ! button >Car > Sys­
tems* control button .
Introduction
The driver inform ation system is controlled
through the multifunction steering wheel
<=.> page 29, fig . 9.
The Driver Information System <=.> fig. 8 contains
the following information:
- @ Tab (register)
- @ Vehicle information
-© Status line (selector lever position, outside
temperature <=.>
page 11)
-@ On-board computer 0, fJ
-© Odometer and trip odometer or on-board
computer
D
N
0
LO 0
> OJ a,
The follow ing functions are possible, depending
on vehicle equipment:
28
@ ®
l. Tab ~ Vehicle functions:
On-board computer, time, date
<=.>page 29
Diesel engine*: remaining range for
Ad Blue <=.>
page 234
Plug-in hybrid drive*: energy flow in-
dicator
<=.> page 106
Plug-in hybrid drive*: range display
<=.>page 102
Efficiency program
<=.>page 31
Plug-in hybrid drive*: digital tachom -
eter
Digital speedometer
Assist
Aud i adapt ive cruise control*
<=.> page 13 2
Audi active lane assist*
<=.> page 142
Lap t i mer* <=.> page 32
Reduc ed display
2. Tab
~I&, Messages and ind icator lights
~ Service reminder indicator
<=.>page252
3. Tab fl I I Audio/ l'>l Radio
4. Tab "'Telephone*
5. Tab
~I~ Navigation*
The second tab is only visib le if at least one indi­
cator light or message is shown or if that system
is switched on.
Display
In the driver information system you will see :
Rad io stat ion or CD
T ime and date
<=.>page 10
Odometer, trip odometer <=.>page 11
Outside air temperature <=.>page 11
Service interval display <=.>page 252
Indicator lights and messages <=.>page 13
Digital speedometer
Lap timer*
<=.>page 32
Cruise control system <=.>page 130

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
Speed warning ¢page 130
Selector lever positions C?page 89
On-board computer display ¢page29
Diesel engine*: remaining C?page 234
range for AdBlue
Plug-in hybr id drive*: d ig ital
C? page 29
tachometer
Plug-in hybrid drive*: range dis-
¢ page 102
play
On-board computer display
The on-board computer display monitors the dif­
ferent memory levels:
- Sho rt-term memory (on-board computer 1)
- Long-term memory (on-boa rd computer 2)
- Efficiency program
The following information can be displayed con­
secutively in the on-board computer:
- Tim e
- Date
- Estimated range based on current fuel level
- Estimated range based on current Ad Blue* level
- T ravel time
- Average consumption
- Average speed
- Distance
- Current fuel consumption
- Engine oil temperature indicator*
On-board computer O (short-term memory)
The short-term memory collects driving informa­
tion from the t ime the ignition is switched on un­
til it is switched off. If you cont inue dr iv ing
with­
in two hours
after switching the ignition off, the
new values are included when calculat ing the cur­
rent trip information. If stopped for more the
two hours, the short term memory is automati­
cally eras ed once you begin driving .
On-board computer fJ (long-term memory)
Unlike the short-term memory, the long-term
memory is not erased automat ically. Yo u can se­
l ect the time period for evaluating trip informa­
tion yourself .
Driver informa tion system
Efficiency program i1
The eff iciency p rogram can help you to use less
fuel<=>page31.
(0 Tips
- Th e on-board computer is controlled by the
left button fields on the multifunction
steering whee l.
- For information on using the other button
fields, such as the audio, telephone* and
navigation* functions, see the MMI owner's
manual.
- Disconnecting the battery causes all the
memory data to be erased .
Operation
Applies to vehicles : wi th drive r info rmation system
The driver information system is controlled with
the multifunction steering wheel.
Fig. 9 Mult ifunct ion steering wheel: Drive r Info rmation
System controls
Fig. 10 Drive r infor mation syste m: open ing t he vehicle
functions menu
In addition to information about the on-board
computer (on-board computer 1 , 2 and the effi­
ciency program) , informat ion about other sys­
tems can also be shown in the display.
29

Driver information system
You can identify which level (on-board computer
1, 2 or the efficiency program) is shown in the
d isp lay based on the small
0 , fJ or the nozzle
ii .
The tab@¢ page 28, fig. 8 is displayed once you
press the button
CD ~ fig. 9 on the mu ltifunction
steer ing wheel.
Operating
• Switch on the ignition. The last select function
is d isp layed.
• To switch between the tabs, press the rocker
button
CD to the left or right~ fig. 9.
• To access additional information below or
above, rotate the thumbwheel @down or up.
• To confirm a selection, press the thumbwheel
@ .
• To select a function programmed to a steering
wheel button, press the button
@ . For addi­
tional information, see ¢
page 30, Assigning
a function to a programmable steering wheel
button
Opening the Vehicle functions
• Select the first tab with the button CD-
• Press the button@. The Vehicle functions
menu is displayed¢ fig. 10.
,.. To select a menu item, turn and press the
thumbwheel @.
Resetting values to zero
• In the Vehicle functions menu, select On­
board computer or Efficiency program.
• Select a value in the desired trip computer or in
the efficiency program.
• To reset the values in a memory, press and hold
the thumbwheel @for one second .
Recalling indicator lights and messages
• Press the button CD repeatedly until the D tab
appears.
The
D tab is only v is ible when there is a mal·
function .
30
Assigning a function to a programmable
steering wheel button
• Select: the IM ENU I button > Car > Systems*
control button > Vehicle settings > Steering
wheel button programming .
The Q tab is only visible when there is at least
one indicator light or message displayed.
@ Tips
- If the vehicle battery is disconnected, all
memory values are erased .
- Information on the efficiency program
¢page 31.
- There is more information o n the multifunc­
t ion steering whee l in the
MMI* owner's
manual.
Boost indicator
App lies to vehicles: wi th boos t pressure indicator
Fig. 11 Instrument cluster: boost indicator
Boost pressure indicator (boost)
A bar graph that begins on the left and fills in to­
ward the r ight indicates the engine 's current load
(mean ing the current boost pressure).