2016 AUDI A3 Owner´s Manual

traction under those conditions. We suggest you
use the recommended snow or all-season tires
specified for your vehicle, or their equivalent.
Refer to
q page 269 for more detai led info rma ­
tion regarding winter tires.
Uniform tire quality grading
- Tr ead wear
- Traction AA A B C
- Temperature ABC
Quality grades can be found where applicable on
the tire side wa ll between tread shoulder and
maximum sect ion w idth
q page 253, fig. 202.
For exampl e: T read wear 2 00 , Traction AA , Tem ­
perature
A .
All passenger car tires must conform to Federal
Safety Requirements in addition to these grades.
Trea d we ar
The tread wear grade is a comparative rating
based on the wear rate of the tire when tested
under contro lled conditions on a specified gov­
ernment test course.
For examp le, a tire graded
150 would wear one
and one ha lf
(11/2) times as well on the govern­
ment course as a tire graded
100.
The relative performance of tires depends upon
the actual conditions of their use, however, and may d epart significant ly from the norm due to
variations in driving habits, service practices and d ifferences in road characteris tics and climate.
Tracti on
The traction grades, from highest to lowest, are
AA, A, B and
C. T hose grades represent the tire's
ability to stop on wet pavement as measured un­
der controlled conditions on specified govern­
ment test surfaces of asphalt and concrete . A tire
marked C may have poor traction performance
q .&. .
,...., Temp eratur e N
0
ii; The temperature grades are A (the h ighest), B,
and C, representing the tire's resistance to the
generation of heat and its ability to diss ipate
Tir es and wheel s
heat when tested under controlled conditions on
a specified indoor laboratory test wheel.
Sustained h igh temperatu re can cause the mate­
ria l of the t ire to degenerate and reduce ti re life ,
and excessive temperature can lead to s udden
tire failure
q .& .
The grade C corresponds to a level of perfo rm­
ance which all passenger car tires must meet un­
der the Federal Motor Vehicle Safety Standa rd
No.
109. Grades Band A represent higher levels
of performance on the laboratory test wheel than
the minim um requ ired by law.
A WARNING
-
The tract ion grade assigned to this t ire is
based on straight -ahead braking traction
tests, and does not include acceleration, cor­ nering, hyd roplaning or pea k traction cha rac­
terist ics.
A WARNING
The temperature grade for this tire is estab­
lished for a tire that is properly infl,;1ted and
not overloaded . Excessive speed, underinfla­
tion, or excessive loading, either separately or i n combination, can cause heat bui ldup and
possib le tire fai lure .
A WARNING
-
-Temperature grades apply to tires that are
p roperly inf lated and not over or under inflat­
ed.
Tire pressure monitoring system
(l) General notes
App lies to vehicles: wi th tir e pressure mo nito rin g syste m
Each tire, including the spare (if provided),
shou ld be checked monthly when cold and inflat-
ed to the inflat io n pressure recommended by the
vehicle manufacturer on the veh icle placard or
t ir e inflation pressure label. (If your ve hicle has
t ir es of a different size than the si ze ind icated on .,..
271

Tires and wheels
the vehicle placard or tire inflation pressure la­
bel, you should determine the proper tire
inflation pressure for those tires).
As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system
(TPMS) that illuminates a low tire pressure tell­
tale when one or more of your tires is significant­ ly under-inflated. Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure . Driving on a signifi­
cantly under-inflated tire causes the tire to over­
heat and can lead to tire failure. Under-inflation
also reduces fuel efficiency and tire tread life,
and may affect the vehicle's handling and stop­
ping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists .
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly .
272
· If the Tire Pressure Monitoring System
indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Fig. 206 Instrument cl uster: i ndic ator lig ht with message
Using the ABS sensors, the tire pressure monitor­
ing system compares the tire tread circumfer­
ence and vibration characteristics of the individu ­
al tires . If the pressure changes in one or more
tires , this is indicated in the instrument cluster
display with an indicator light
Rt] and a message
¢fig. 206. If only one tire is affected, the loca­
tion of that tire will be indicated. The message
turns off after a few minutes. You can display the
message again¢
page 30.
The tire pressures must be stored in the menu
display again each time the pressures change
(switching between partial and full load pres­
sure) or after changing or replacing a tire on your
vehicle
¢ page 273. The tire pressure monitor­
ing system only monitors the tire pressure you
have stored . You can find the recommended tire
pressures for your vehicle on the label on the
driver's door pillar¢
page 263.
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if:
- If the tire pressure in one or more tires is too
low,
- the tire has structural damage,
- The tire was replaced or the tire pressure
changed and it was not stored again
¢page 273.
-the spare tire is installed.

,....,
N
0 > co ,...., Indicator lights
IE-Loss of pressure in at least one tire c::> ,&.
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires. Then
store the tire pressures in the MMI
c::> page 2 73 .
mm (Tire Pressure Monitoring System) Tire
pressure: System malfunction!.
If m appears
after switching the ignition on or whi le driving
and the
IE indicator light in the instrument clus­
ter blinks for approximately one minute and then
stays on, there is system malfunction. Try to
store the correct tire pressures
c::> page 2 73. If
the indicator light does not turn off or turns on
again after a short period of time, drive to an au­
thor ized Audi dealer or authorized Audi Service
Facility immediately to have the malfunction cor­
rected.
A WARNING
- If the tire pressure warning light IE in the
instrument cluster turns on, the pressure in
one or more tires is too low . Reduce the ve­
hicle speed immediately and avoid any hard
steering or braking maneuvers. Stop as soon
as possible, check the tire and inflate the
t ir e to the correct pressure, which is speci­
fied on the tire pressure label on the veh icle
c::> page 263. Driving with a ti re with low
pressure causes the tire to overheat and can
result in failure of the tire. Low pressure can
also have a negative effect on the driving
and braking behavior of the vehicle .
- Th e driver is responsible for maintaining the
correct tire pressures. You must check the
tire pressures regularly.
- Under certain conditions (such as a sporty
driv ing style, winter conditions or unpaved
roads), the pressure monitor indicator may
be delayed.
- Do not use run-flat tires on your vehicle . Us­
ing them when not permitted can lead to
vehicle damage or accidents.
(D Tips
- The tire pressure monitoring system can al ­
so stop working when there is an ESC mal­
function.
Tires and wheels
-Using snow chains may result in a system
ma lfunction.
- The tires with the identification "AO" or
"RO"
c::> page 260 have been matched with
your Audi tire pressure monitoring system .
We recommend that you use these tires.
- The tire pressure monitoring system can on­
ly monitor the tire pressure of the driving
tires. Check the tire pressure of the spare
wheel in the luggage compartment so that if necessary it is ready for use.
Storing tire pressures
Applies to vehicles: with tire pressure mon itor ing system
A change in tire pressure or a change in tires
must be stored in the system.
The tire pressure is stored in the MMI.
.,. Make sure befo re storing that the tire pressures
of all four tires meet the specified va lues and
are adapted to the load. Otherwise the system
could malfunction
c::> page 263.
.. Switch on the ign ition.
.,.. Select: the I MENU I button> Car> Systems "
control button > Service & control > Tire pres­
sure monitor > Store tire pressure > Yes, store
now .
(D Tips
Do not store the tire pressures if snow chains
a re installed . Otherwise the system could
malfunction.
273

Care and cleaning
Care and cleaning
General information
Regular, prope r care helps to maintain your vehi ­
cle's value.
It can a lso be a requirement when
submitting war ranty claims for cor rosion damage
and pa int defects on the body.
The necessary care prod ucts can be obtained
from an autho rized Audi deale r or authorized
Aud i Service Facility. Read and follow the instruc­
tions for use on the packaging.
A WARNING
- Using clean ing and care products incorrectly
can be dangero us to your hea lth .
- Always store clean ing and care products out
of reach of children to reduce the r isk of po i­
so ning .
@ For the sake of the environment
- Preferably use environmentally-friendly
products when buying cleaning agents.
- Do not dispose of leftove r clean ing and care
products with household t rash.
Car washes
The longer that deposits s uch as insects, bird
droppings, tree sap or road salt remain on the ve­ h icle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
i n crease the damag ing effect .
Before washing, r inse off heavy deposits with
p lenty of water.
St ubb orn deposits such as bird droppings or tree
sap are best removed with plenty of wate r and a
microfiber cloth.
Also, wash the underside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washing your veh icles with a pressure
washer, always follow t he ope ra ti ng ins tructions
p rovided w ith the pressure washer. This is espe­
cially important in regard to the pressure and
spraying distance . Do not aim the spray directly
274
at seals on side windows, doors, the hood, the
lug gage compartment lid or the sunroof* or at
t ir es, rubbe r hoses, insulating material, sensors*
or camera lenses*. Keep a distance of at least 16
i nches (40 cm).
Plug -in hybrid drive*: also do not direct the spray
at the charg ing unit in the rad iator g rille or at the
charg ing dock*.
Do not remove snow and ice with a pressure
washer.
Neve r use rot ary no zzles or high pressure noz­
z les.
The wate r temperatu re must not be above 140 °F
(60 °() .
Automatic car washes
Spray off the veh icle before washing.
Make sure that the windows and roof* are closed
and the windshie ld wipers are off. Follow instruc ­
tions from the car wash operato r, especially if
there are accesso ries attached to your vehicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean the ve hicle starting from the top and work­
i ng down using a soft sponge or clea ning brus h.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avo id damaging the paint w hen washing, fi rst
remove dust and large pa rticles from your vehi­
cle. Insects, grease spots and f ingerprints are
best removed w ith a special cleaner for matte
finish paint.
Apply t he product using a microf iber cloth. To
avo id damaging the paint surface, do not use too
much pressure.
Rinse the ve hicle thoroughly with wate r. Then
clean using a neutra l shampoo and a soft micro ­
fiber clot h.
Rinse the vehicle thorough ly again and le t i t air
dry. Remove any water residue using a sham my. ..,..

,....,
N
0 > co ,...., & WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
-After washing the vehicle, the brak ing effect
may be delayed due to mo isture on the
brake rotors or ice in the w inter . The brakes
must be dried first w ith a few careful brake
applica tions .
{[) Note
-If you wash t he vehicle in an automatic car
wash, yo u m ust fold the e xterior m irrors i n
to reduce the risk of damage to the mi rrors.
Power folding exte rior m irrors* must o nly
b e fo lded in a nd out usin g the power folding
f u nct io n.
-
Ca re and cleaning
- To prevent pa int damage, do not wash the
vehicle in direct s un light .
- To re duce the risk of damage to the surface,
do not use insect removing sponges, kitche n
sponges o r similar items .
- Matte finish painted veh icle components:
- To reduce the r isk of damage to the sur-
face, do not use po lish ing agents or hard
wax.
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint . The paint cou ld be damaged
when the stickers or magne ts are re ­
moved.
@ For the sake of the environment
Only wash t he veh icle in facili ties s pec ially de­
s igned for that pu rpose . This will reduce the
r isk of dirty wate r contamina ted with o il from
ente ring the sewe r sys tem.
Cleaning and care information
W hen clea ning and ca ring for individua l vehicle
comp onents, refer to the following t ables. The
inf ormat ion cont ained there is s imp ly recom ­
mendations. For q uest ions or for components t
h at are not l isted, cons ult an autho riz ed Aud i
de aler or author ized A udi Se rvice Fa cility. Also
f o llow the information fo und in ~ .&. .
Ext erior cleaning
Component Situation Solution
Windshield wiper
D eposits ~ page 53, Cleaning windshield wiper blades
blades
Headlights /
Deposits So
ft spo nge with a m ild soap solutiona)
Tail lights
Sensors /
Deposits Sensors: soft cloth w ith solvent-free cleaning solution
camera lenses Camera lenses: soft cloth w ith alcohol-free cleaning solu-
tion
Snow/ice Hand br
ush/solven t-free de -icing spray
Wheels Road salt Water
Brake dust Acid-free special clean
ing so lution
Exhaust tail p ipes Road salt Water, clea ning so lu tion su itab le for s tainless stee l, if nee-
essary
Decorati ve parts / Deposits Mild soap so lution a>, a cleaning solution su itable for stain-
Trim less stee l, if necessary
275
...

Care and cleaning
Component Situation Solution
Paint
Paint damage Refer to the paint number on the vehicle data label, repair
with touch up paint¢
page 301
Spilled fuel Rinse with water immediately
Surface rust Rust remover, then protect with hard wax; for questions,
consult an authorized Audi dealer or authorized Audi Serv-
ice Facility.
Corrosion Have
it removed by an authorized Audi dea ler or a uthor-
ized A udi Service Facility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen w ith water immediately and remove with a micro-
sects, bird dropp ings, f iber cloth
tree sap and road salt
Grease-based con- Remove immediately wi th a mild soap solution al and a
taminants such as
soft cloth
cosmetics or sunblock
Carbon parts Deposits clean the same way as painted parts¢ page 2 74
Decorative decals Deposits Soft sponge with a mild soap solutional
Audi e-tron Deposits Dry towe l
charging system *
Charging dock*
Deposits Soft towel with alcoho l-free cleaning so lution
a} Mild soa p sol ution: maxim um two tablespoons of neutral soap in 1 quart (I liter) of water
Internal cleaning
Component Situation Solution
Windows
Deposits Glass cleaner, then wipe dry
Decorative parts/ Deposits Mild soap solutional
Trim
Plastic parts
Deposits Damp cloth
Heavier deposits Mild soap so lution al, detergent-free p lastic clean ing solu-
tion, if necessary
Displays Deposits Soft cloth with LCD cleaner
Controls Deposits Soft brush, then a soft cloth with a mild soap solutional
Safety belts Deposi ts Mild soap solution al, allow to dry before letting them re-
tract
276

,..,
N
0 > co ,.., Care and cleaning
Component Situation Solution
T ex til es
Deposits adhering to Vacuum cleaner
art ificial l eather, the surface
A lcan tara Water-based deposits Absorbent
cloth and mild soap solutiona>
such as coffee, tea,
b lood, etc.
Oil -based deposits Apply a m ild soap solution
a), blot away the dissolved o il or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Special stain
remover, blot with absorbent material, treat
as ink, nail polish, la- afterward with mild soap solution, if necessary
a)
tex paint, shoe pol-
ish, etc.
Natu ral le ath er Fresh stains Wool cloth with a mild soap solution a)
Water-based deposits Fresh stains: absorbent cloth
such as coffee, tea, Dried stains : stain
remover suitable fo r leather
b lood , etc.
Oi [-based deposits Fresh stains: absorbent cloth and stain
remover suitable
such as oil, make-up, for leather
etc. Dried stains : grease dissolving spray
Special deposits such Spot remove r suitab le for leather
as ink, nai l polish, la-
tex paint, shoe pol-
ish, etc.
Care Regularly apply condit ion ing c ream that protects from
lig ht and penet rates into the material. Use specia lly-co l-
ored conditioning cream, if necessary .
Carbon part s Deposits clean the same way as plast ic parts
a) Mi ld soap solution: maximum two tablespoons of neutral soap in 1 q uart (1 liter) of water
.8, WARNING
The windshield may not be trea ted with wa­
ter-repelling windshield coating agents. Un ­
favorable cond itions such as wetness, dark­
ness, or low sun can result in increased glare.
Wiper blade chatter is also possible.
A WARNING
- Audi e -tron charg ing sy stem *
- Never immerse the charging system and
connectors in water.
- The charging system m ust only be cleaned
when the control unit is completely d is­
connected from the powe r su pply system
and from the vehicle.
-
({I) Note
- Hea dlight s/tail lights
- Never clean headlights or tail lights w ith a
d ry cloth or sponge.
- Do not use any cle aning product that con­
tains alcoho l, because they could ca use
cracks to form.
-Whe els
- Never use any pa int polish or other abra-
sive materials.
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately .
-Sensor s/came ra le nses Ill-
277

Care and cleaning
- Never use warm or hot water to remove snow or ice from the camera lens. This
cou ld cause the lens to crack.
- Never use abrasive clean ing mater ia ls or
alcoho l to clean the camera lens. This
cou ld cause scratches and cracks.
- Door windo ws
- Remove snow and ice on windows and ex -
terior mirrors with a p lastic scraper. To
avoid sc ratches, move the scrape r on ly in
one direction and not back and forth .
- Never remove snow o r ice from doo r win­
dows and m irrors using warm or hot water
because this could cause cracks to form.
- To avoid damage to the rear w indow de­
fogge r, do not apply any sticke rs on the
heating w ires on the inside of the window.
- Decorative parts /trim
- Never use chrome care or cleaning prod-
ucts.
-Paint
-To reduce the risk of scratches, the vehicle
must be free of dirt and dust before pol ­
ishing or waxing .
- To prevent pa int damage, do not polish or
wax the veh icle in direct sunlight .
- To reduce the risk of pa int damage, do not
polish away rust spots .
- Remove cosmetics and sunscreen immedi­
ately- these could damage the paint.
-Di splays
- To avoid scratches, do not use dry cleaning
methods on displays.
- Controls
- Make sure that no fluids enter the con -
trols, because this could cause damage .
-Safet y belt s
-Do not remove the safety belts to clean
them.
- Never clean safety belts or their compo­ nents chemically or with corrosive flu ids
or so lvents and never allow sharp objects
to come into contact w ith the safety belts .
Th is could cause damage to the belt web­
bing.
- If there is damage to the webbing, the
connect ions, the retractors or the b uck les,
278
have them replaced by an authorized Aud i
dealer or authorized Audi Service Facility.
- Te xtile s/artificial l eath er/ Alcantara
- Never treat art ificial leather/ A lcantara
with leather care products , solvents, floor
polish, shoe polish, spot remove or s imilar
p roducts .
- Have a spec ialist remove stubborn stains
to prevent damage .
- Never use steam cleaners, brushes, hard
sponges, etc . when cleaning .
- Do not turn on the seat heating* to dry the
seat .
- Ob jects w ith sharp edges such as zippers,
rivets on clothing or be lts can cause dam­
age to the surface .
- Open hook and loop fasteners, for exam­
p le on clothing, can damage seat covers .
Make sure hook and loop fasteners are
closed .
-Natural l eather
-Neve r treat leather wi th solvents , floor
polish, shoe polish, spot remover or sim i­
lar products .
- Obje cts w ith sharp edges such as zippers ,
rivets on clothing or be lts can cause dam ­
age to the surface .
- Neve r use s team cleaners, brushes, hard
sponges, etc . when cleaning .
- D o not turn on the seat heating* to dry the
seat.
- To he lp prevent the leather from fad ing,
do not leave the vehicle in d irect sunlight
for long periods of time . If leaving the ve ­
hicle parked for long periods of time, you
should cover the leather to protect it from
d irect sunlight.
{D Tips
- Insects are easier to remove from paint that
has been freshly waxed.
- Regular waxing can prevent rust spots from
forming.