2015 Peugeot RCZ Owner's Manual

47
RCZ_en_Chap02_ouvertures_ed01-2015
CLOSING
The window rises automatically after a few seconds and adjusts to
provide perfect sealing when closed.-

when the engine is running
, this warning lamp comes on,
accompanied by a message in the screen for a few seconds,
CENTRAL LOCKING CONTROL
This control permits simultaneous locking or unlocking of the doors,
boot
lid and fuel filler flap from inside the vehicle.
Locking
F Press this button to lock the vehicle.
The red indicator lamp on the button comes on.
If one of the doors or the boot lid is open, the central locking from
the inside does not take place.
Unlocking
F Press this button again to unlock the vehicle.
The red indicator lamp on the button goes of f.
Locking / deadlocking from the outside
When the vehicle is locked or deadlocked from the outside, the
red indicator lamp flashes and the button is inactive.
F

With normal locking, pull on the interior door control lever to
unlock the vehicle.
F


With deadlocking, you have to use the remote control or the
key to unlock the vehicle.
When washing your vehicle:
-

first

lock

the

vehicle

using

the

remote

control

or

the

key,
-

avoid spraying the upper part of the windows,
-


keep the end of the high pressure nozzle at least 1 metre from
the windows and door seals.
When a door is not closed correctly:
Be aware of the risk of pinching when the window rises
automatically on closing the door

.
-

when the vehicle is moving
(speed higher than 6 mph (10 km/h)),
this warning lamp comes on, accompanied by an audible signal and
a message in the screen for a few seconds.
2/
ACCESS

48
RCZ_en_Chap02_ouvertures_ed01-2015
Pressing the central locking control unlocks the vehicle.
Opening a door from the inside, when stationary, also unlocks the
vehicle, but the vehicle will be locked again when the speed exceeds
6 mph (10 km/h).
Activation / deactivation
You can activate or deactivate this function.
F
With the ignition on, press the button for more than two seconds.
A


confirmation message appears in the screen.
EMERGENCY LOCKING
To lock or unlock the doors mechanically in the event of a central
locking
system failure or flat battery.
Locking the driver's door
F Insert the key in the lock, then turn it to the right.
Unlocking the driver's door
F Insert the key in the lock, then turn it to the left.
Locking the passenger door
F Using the key, remove the black cap on the edge of the door.
F
Insert the key in the cavity without forcing, then without turning it,
move the the latch sideways towards the interior of the door

.
F Remove
the key and refit the cap.
Unlocking the passenger door
F Pull the interior door opening control.
ANTI-INTRUSION SECURITY
This function permits automatic and simultaneous locking of the doors,
boot lid and fuel filler flap as soon as the vehicle speed exceeds 6 mph
(10 km/h).
Operation
If one of the doors is open, the automatic central locking does not take\

place.
If the boot lid is open, the automatic central locking of the doors is
active.

49
RCZ_en_Chap02_ouvertures_ed01-2015
BOOT
OPENING
F Press this button for more than two seconds to unlock
the boot lid. The boot lid opens slightly.
F

Lift the boot lid.
This


action
also unlocks the doors and the fuel filler flap.
Using the manual control; vehicle unlocked
F Press the opening control above the number plate.
F
Lift the boot lid.
CLOSING
F Lower the boot lid using one of the interior grab handles.
F
If necessary
, press the top of the boot lid to close it fully.
If the boot lid is not closed correctly: -

when the engine is running
, this warning lamp comes on,
accompanied by a message in the screen for a few seconds,
When selective unlocking is activated, the boot can also be
opened by a second press on the open padlock on the remote
control.
Using the remote control
Emergency locking
If the central locking system fails (flat battery), you are advised to disconnect the battery.
-

when the vehicle is moving
(speed above 6 mph (10 km/h)), this
warning lamp comes on, accompanied by an audible signal and a
message in the screen for a few seconds.
Never grasp the boot lid by the active spoiler
.
2/
ACCESS

50
RCZ_en_Chap03_confort_ed01-2015
FRONT SEATS
Seat with integral head restraint, consisting of a seat cushion and a se\
at
back which can be adjusted to adapt your position for ease of driving
and comfort.
MANUAL A dj USTMENTS
Forwards-backwards adjustment Seat height adjustment
Seat back angle adjustment
F Raise the control bar and slide the seat forwards or backwards. F
Pull the control lever upwards to raise or push it downwards to
lower

, as many times as necessary, to obtain the position required.
F Turn the knob to set the angle required.
Before moving the seat backwards, ensure that there is nothing
that might prevent the full travel of the seat, so as to avoid the risk \
of of jamming the seat caused by the presence of objects on the
floor
behind the seat or rear passengers. If the seat jams, stop the
movement immediately

.

51
RCZ_en_Chap03_confort_ed01-2015
FRONT SEATS
Seat with integral head restraint, consisting of a seat cushion and a se\
at
back which can be adjusted to adapt your position for ease of driving
and comfort.
ELECTRIC A dj USTMENTS
Forwards-backwards adjustment Seat cushion height adjustment
F Push the control forwards or rearwards to slide the seat. F
T
ilt the rear part of the control upwards or downwards to obtain the
required height.
The electrical functions of the seat are deactivated approximately
one minute after the ignition is switched off.
To reactivate them, switch on the ignition.
Carry out these adjustments with the engine running to avoid
discharging the battery.
Seat back angle adjustment
F Tilt the control forwards or rearwards to adjust the angle of the seat
back.
Before moving the seat backwards, ensure that there is nothing
that might prevent the full travel of the seat, so as to avoid the risk \
of of jamming the seat caused by the presence of objects on the
floor

behind

the

seat

or

rear

passengers.

If

the

seat

jams,

stop

the

movement immediately

.
3/
EASE OF USE and COMFORT

52
RCZ_en_Chap03_confort_ed01-2015
MANUAL LUMBAR A dj USTMENT
F Turn the knob manually to obtain the desired level of lumbar
support.
HEATEd SEATS CONTROL
With the engine running, the front seats can be heated separately.
F

Use the adjustment dial, placed on the side of each front seat, to
switch

on and select the level of heating required:
0: Off.
1: Low.
2: Medium.
3: High.

53
RCZ_en_Chap03_confort_ed01-2015
STORING DRIVING POSITIONS
System which takes into account the electrical settings of the driver's \
seat and the door mirrors. It enables you to store two positions using
the buttons on the side of the driver's seat.
STORING A POSITION
Using buttons M / 1 / 2
F Switch on the ignition.
F
Adjust your seat and your door mirrors.
F


Press button
M, then press button 1 or 2 within four seconds.
An audible signal is heard indicating that the settings have been
stored.
RECALLING A STORE d POSITION
Storing a new position cancels the previous position.
Using button 1 or 2
F Press and hold button 1 or 2 until the audible signal is heard
indicating the end of the adjustment.
When the ignition is off, after a few consecutive position recalls,
the function will be deactivated until the engine is started,
to
prevent discharging of the battery.
3/
EASE OF USE and COMFORT

54
RCZ_en_Chap03_confort_ed01-2015
STEERING WHEEL AD j USTMENT
F When stationary, pull the control lever to release the adjustment
mechanism.
F

Adjust the height and reach to suit your driving position.
F


Push the control lever to lock the adjustment mechanism.
As a safety precaution, these operations should only be carried
out with the vehicle stationary

.