2015 Peugeot RCZ Owner's Manual

23
RCZ_en_Chap01_controle-de-marche_ed01-2015
SERVICE INdICATOR
This information is displayed for a few seconds when the ignition is
switched on. It informs the driver when the next service is due, in
accordance with the manufacturer's service schedule.
The point at which the service is due is calculated from the last indica\
tor
zero reset. It is determined by two parameters:
-
the distance travelled,
-


the time elapsed since the last service (only on HDi Diesel
versions).
More than 1 800 miles (3 000 km) remain before the next service is due\
When the ignition is switched on, no service information appears on the \
instrument panel central screen.
Between 600 miles (1 000 km) and 1 800 miles (3 000 km)
remain before the next service is due
For a few seconds after the ignition is switched on, the spanner
symbolising the service operations comes on. The instrument panel central
screen indicates the distance remaining before the next service is due.
Example: 1 700 miles (2 800 km) remain before the next service is due.
For a few seconds after the ignition is switched on, the central screen
indicates:
Less than 600 miles (1 000 km) remain before the next service is due
Example: 500 miles (900 km) remain before the next service is due.
For a few seconds after the ignition is switched on, the central screen \
indicates:
The spanner remains on in the small screen
to indicate that a service must be carried out
soon.
1/
MONITORING

24
RCZ_en_Chap01_controle-de-marche_ed01-2015
Service overdue
For a few seconds after the ignition is switched on, the spanner
flashes to indicate that the service must be carried out as soon as
possible.
Example: the service is overdue by 300 miles (300
km).
For a few seconds after the ignition is switched on, the central screen \
indicates:
The spanner remains on in the small screen
to indicate that a service should have been
carried out.
The distance remaining may be weighted by the time factor,
depending on the type of motoring the vehicle is used for.
Therefore, the spanner may also come on if you have exceeded
the
period since the last service specified in the manufacturer's
service schedule.
This indication applies only to HDi Diesel engines.
Service indicator reset
Retrieving the service information
You can access the service information at any time.
This information appears when running through the manual check
procedure.
F Briefly press the "CHECK/000" button.
The service information is displayed for a few seconds on the
instrument panel central screen, then disappears.
Following this operation, if you wish to disconnect the battery

,
lock the vehicle and wait at least five minutes for the reset to be
registered.
After each service, the service indicator must be reset.
If you have carried out the service on your vehicle yourself:
F

switch of
f the ignition,
F
press and hold the
"CHECK/000" button,
F

switch on the ignition; the distance recorder display begins a
countdown,
F

when the instrument panel central screen indicates
"=0"
, release
the button; the spanner disappears from the small screen.

25
RCZ_en_Chap01_controle-de-marche_ed01-2015
MANUAL CHECK
This function allows you to check the status of the vehicle (reminder o\
f
the active alert warnings) and the service information.
F With
the engine running, to start a manual check, briefly press the
"CHECK/000" button on the instrument panel.
If no faults have been detected,

"CHECK OK" appears in the
instrument panel central screen.
If a "minor" fault has been detected, the warning lamp concerned then
"CHECK OK" appear in the instrument panel central screen. Contact a
PEUGEOT


or a qualified workshop.
If a "major" fault has been detected, only the warning lamps concerned
appear in the instrument panel central screen. Have it checked by a
PEUGEOT


dealer or a qualified workshop.
dISTANCE RECORdERS
The total and trip distances are displayed for thirty seconds when the
ignition is switched off, when the driver's door is opened and when the
vehicle is locked or unlocked.
Measures the total distance travelled by the vehicle since its first
registration.
Total distance recorder
F With the ignition on, press and hold this button until zeros appear .
Trip distance recorder
Measures the distance travelled since it was last reset to zero by the
driver.
1/
MONITORING

26
RCZ_en_Chap01_controle-de-marche_ed01-2015
LIGHTING dIMMER
Permits manual adjustment of the brightness of the instruments and
controls to suit the ambient light level. Only operates when the vehicle\

lighting is on, with the exception of the daytime running lamps.
Activation
F Press the button to change the brightness of the instruments and
controls.
F

When the lighting reaches the minimum setting, release the button,
then press again to increase it.
or
F


When the lighting reaches the maximum setting, release the button,
then press again to reduce it.
F

When the lighting reaches the level of brightness required, release
the button.
deactivation
When the vehicle lighting is off, or in day mode on vehicles fitted with daytime running lamps, pressing the button does not have any effect.
CLOCK
The analogue clock, located between the central vents of the
dashboard, does not have an adjustment button.
To set the time, refer to the section relating to your multifunction
screen's
configuration menu.
The clock is synchronised with the multifunction screen time; once the
the
setting has been confirmed on the multifunction screen, the hands
will turn to synchronise with the screen, and each time the ignition is \
switched on.

27
RCZ_en_Chap01_controle-de-marche_ed01-2015
display of information
F Cycle through the information with successive short presses on this
button.
TRIP COMPUTER
CENTRAL INSTRUMENT PANEL SCREEN
C

ENTRAL

INSTRUMENT PANEL

SCREEN WITH
NA

VIGATION
System that gives you information on the current journey (range, fuel
consumption…).
1/
MONITORING

1
2
28
RCZ_en_Chap01_controle-de-marche_ed01-2015
The trip computer can display:-
The current information tab, for the trip in use, with:
●

the range,
● the
current fuel consumption.
-

The trip
"1" tab with:
● the
distance travelled,
● the
average fuel consumption,
● the
average speed.
-

The trip
"2" tab with:
● the
distance travelled,
● the
average fuel consumption,
● the
average speed.
F

Pressing the button again takes you to a black screen.
A

further press returns you to the normal display.Trip reset
F When the trip required is displayed, press this button.
T rips "1" and "2" are independent but their use is identical.
For example, trip "1"
can be used for daily figures, and trip
"2"
for
monthly
figures.

29
RCZ_en_Chap01_controle-de-marche_ed01-2015
TRIP COMPUTER , A FEW d EFINITIONS
Range
(miles or km)
The distance which can still be travelled with the fuel
remaining in the tank (related to the average fuel consumption over the\

last few miles (kilometres) travelled).
This value may vary following a change in the style of driving
or

the

relief, resulting in a significant change in the current fuel
consumption.
If dashes are displayed continuously while driving in place of the
digits,


contact a PEUGEOT

dealer or a qualified workshop.
This function is only displayed from 20 mph (30 km/h).
When the range falls below 20 miles (30 km), dashes are displayed.
After

filling

with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (100 km).
Current fuel consumption
(mpg or l/100 km or km/l)
Calculated over the last few seconds.
Average fuel consumption
(mpg or l/100 km or km/l)
Calculated since the last trip computer reset.
Average speed
(mph or km/h)
Calculated since the last trip computer reset.
distance travelled
(miles or km)
Calculated since the last trip computer reset.
1/
MONITORING

30
RCZ_en_Chap01_controle-de-marche_ed01-2015
MONOCHROME SCREEN C (WITH
P EUGEOT
C
ONNECT
S
OUND (RD5))
dISPLAYS IN THE SCREEN
Displays according to context:
-
time,
-
date,
- ambient
temperature (the value displayed flashes if there is a risk of
ice),
-


visual parking assistance,
-


audio functions,
-


alert messages,
-

the display and vehicle equipment settings menus.
CONTROLS
From the control panel of your PEUGEOT Connect Sound (RD5), you
can:
F

press the
"MENU" button for access to the main menu,
F

press the "
5" or "6" buttons to scroll through the items on the
screen,
F

press the
"MO d E" button to change the permanent application
(audio source, telephone...),
F

press the "
7" or "8" buttons to change a setting value,
F

press the
"OK" button to confirm,
or
F

press the
"Back" button to abandon the operation in progress.