2015 Peugeot RCZ Owner's Manual

151
RCZ_en_Chap08_info-pratiques_ed01-2015
dESCRIPTION OF THE KIT
A. "Sealant" or "Air" position selector .
B. On "I" / off "O" switch.
C. Deflation
button.
d

.
Pressure gauge (in bar and p.s.i.).
E.


Compartment housing:
-


a cable with adaptor for 12 V socket,
-

various inflation adaptors for accessories, such as balls,
bicycle

tyres... F. Sealant cartridge.
G.
White pipe with cap for repair
.
H. Black
pipe for inflation.
I.

Speed limit sticker
.
The speed limit sticker I
must be affixed to the vehicle's steering
wheel to remind you that a wheel is in temporary use.
Do not exceed a speed of 50 mph (80 km/h) when driving with a
tyre repaired using this type of kit.
The vehicle's electric system allows the connection of a
compressor

for long enough to inflate a tyre after a puncture repair
or

for inflating a small inflatable accessory.
8/
PRACTICAL INFORMATION

152
RCZ_en_Chap08_info-pratiques_ed01-2015
Take care, this product is harmful (e.g. ethylene-glycol,
colophony...) if swallowed and causes irritation to the eyes.
Keep this product out of the reach of children.
REPAIR PROCEdURE
1. Sealing
F Switch off the ignition. F
Uncoil the white pipe
G
fully.
F Unscrew the cap from the white pipe.
F Connect the white pipe to the valve of the tyre to be repaired.
F

Connect the compressor's electric plug to the vehicle's 12 V socket.
F


Start the vehicle and leave the engine running.
A

void removing any foreign bodies which have penetrated into
the tyre.
F

T
urn the selector A to the "sealant" position.
F

Check that the switch
B is in position "O".

153
RCZ_en_Chap08_info-pratiques_ed01-2015
F Switch on the compressor by moving the switch B to position "I"
until the tyre pressure reaches 2.0 bars.
The sealant is injected into the tyre under pressure; do not
disconnect the pipe from the valve during this operation (risk of
splashing). F

Remove the kit and screw the cap back on the white pipe.
Take care to avoid staining your vehicle with traces of fluid. Keep
the kit to hand.
F

Drive immediately for approximately three miles (five kilometres),

at reduced speed (between 15 and 35 mph (20 and 60 km/h)), to
plug the puncture.
F


Stop to check the repair and the tyre pressure using the kit.
Do not start the compressor before connecting the white pipe
to the tyre valve: the sealant product would be expelled through
the pipe.
Tyre under-inflation detection
If the vehicle is fitted with tyre under-inflation detection,
the under-inflation warning lamp will remain on after the wheel
has been repaired until the system is reinitialised by a PEUGEOT


dealer
or a qualified workshop.
If after around 5 to 7 minutes the pressure is not attained, this
indicates that the tyre is not repairable; contact a PEUGEOT
dealer

or

a

qualified

workshop

for

assistance.
8/
PRACTICAL INFORMATION

154
RCZ_en_Chap08_info-pratiques_ed01-2015
2. Inflation
F Turn the selector A to the "air" position.
F
Uncoil the black pipe H

fully.
F

Connect the black pipe to the valve of the wheel.
As

soon as possible, go to a PEUGEOT

dealer or a qualified
workshop.
Y

ou must inform the technician that you have used this kit. After
inspection, the technician will advise you on whether the tyre can
be repaired or if it must be replaced.
F

Connect the compressor's electric plug to the vehicle's 12 V socket.
F


Start the vehicle again and leave the engine running. F

Adjust the pressure using the compressor (to inflate: switch B
in position "I";
to deflate: switch B in position "O" and press
button
C), in accordance with the vehicle's tyre pressure label
(located on the left hand door aperture).
A

loss of pressure indicates that the puncture has not been fully
plugged;
contact a PEUGEOT

dealer or qualified workshop for
assistance.
F


Remove and stow the kit.
F


Drive at reduced speed (50 mph [80 km/h] max) limiting the
distance travelled to approximately 120 miles (200 km).

155
RCZ_en_Chap08_info-pratiques_ed01-2015
Beware of discharges of fluid.
The expiry date of the fluid is indicated on the cartridge.
The sealant cartridge is designed for single use; even if only partly
used, it must be replaced.
After use, do not discard the cartridge into the environment, take it
to an authorised waste disposal site or a PEUGEOT dealer.
Do not forget to obtain a new sealant cartridge, available from
PEUGEOT


dealers or from a qualified workshop.
REMOVING THE CARTRI d GE
F Stow the black pipe.
F
Detach the angled base from the white pipe.
F


Support the compressor vertically
.
F

Unscrew the cartridge from the bottom.
8/
PRACTICAL INFORMATION

156
RCZ_en_Chap08_info-pratiques_ed01-2015
CHECKING TYRE PRESSURES /
INFLA

TING
ACCESSORIES
You can also use the compressor, without injecting any product, to:
-

check or adjust the pressure of your tyres,
-

inflate other accessories (balls, bicycle tyres...).
F

T
urn the selector A to the "Air" position.
F

Uncoil the black pipe H

fully.
F

Connect the black pipe to the valve of the wheel or
accessory

.
If
necessary, fit one of the adaptors supplied with the kit first.F

Connect the compressor's electrical connector to the vehicle's 12 V
socket.
F


Start the vehicle and let the engine run.
F

Adjust the pressure using the compressor (to inflate: switch
B

in position "I";
to deflate: switch B in position "O" and press
button
C), according to the vehicle's tyre pressure label or the
accessory's pressure label.
F

Remove the kit then stow it.

157
RCZ_en_Chap08_info-pratiques_ed01-2015
CHANGING A WHEEL
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level, stable and non-slippery ground.
Apply the parking brake, switch off the ignition and engage first
gear (position P

for the automatic gearbox) to lock the wheels.
Check
that the parking brake indicator lamps are on fixed (not
flashing)

in the instrument panel.
It is imperative that you ensure that the occupants get out of the
vehicle and wait where they are safe.
If necessary, place a chock under the wheel diagonally opposite
the wheel to be changed.
Never go underneath a vehicle raised using a jack; use an axle
stand.
Security socket: for adaptation of the
wheelbrace to the special "security" bolts.
Specific

to

your

vehicle,

it

is

stored

in

the

glove box.
Wheelbrace:


for

removal

of

the

wheel

fixing

bolts.
j

ack with integrated handle: for lifting the
vehicle.
TOOLS REQUIRE d*
Bolt cover removal tool: for removal of the
bolt
finishers (covers) on alloy wheels.
*

Depending


on

the

country of sale, the vehicle may be equipped with
the tools needed to change a wheel and a spare wheel (see following
pages). Do not use:
-


the jack for any purpose other than lifting the vehicle,
-


a jack other than the one supplied with the vehicle.
If the jack supplied with the vehicle is not present, contact a
PEUGEOT


dealer or a qualified workshop to obtain the jack
defined

for the vehicle by the manufacturer.
8/
PRACTICAL INFORMATION

158
RCZ_en_Chap08_info-pratiques_ed01-2015
REMOVING A WHEEL
F Position the foot of the jack on the ground directly below one of
the two front A or rear B jacking points provided on the underbody,
whichever is closest to the wheel to be changed.
F

Remove the cover on each of the bolts using the bolt cover removal
tool.
F

Fit the security socket on the wheelbrace to slacken the security
bolt.
F

Slacken the other bolts using the wheelbrace only
.
F
Extend the jack until its head comes into contact with the jacking
point

A or B used; the vehicle's contact area
A or B must be
correctly engaged with the central part of the head of the jack.
Ensure that the jack is stable. If the ground is slippery or loose,
the jack may slip or drop. - Risk of injury!
Ensure that the jack is positioned only at one of the jacking
points A or B under the vehicle, making sure that the vehicle's
contact area is centred on the head of the jack. Otherwise there is
a risk of damage to the vehicle and/or of the jack dropping - Risk
of injury!