2013 SKODA OCTAVIA Owner's Manual

No.Power consumer45Control unit for control of seat adjustment46230-Volt power socket47Rear window wiper48Not assigned49Coil on starter relay, clutch pedal switch50Not assigned51Belt tensioner - front passenger side52Not assigned53Relay for rear window heater

Fuses in the engine compartment
Fig. 218
Fuse box cover in engine compartment/Schematic diagram of the
fuse box
Fig. 219
Cover for the fuse box in the en-
gine compartment: Plastic clip
for fuses
First read and observe the introductory information and safety warn-
ings on page 251.
Replacing fuses
›
Press together the interlocks of the cover simultaneously in the direction of the
arrow
1
» Fig. 218 .
›
Remove the cover in the direction of the arrow
2
.
›
Replace the appropriate fuse.
›
Place the cover on top of the fusebox.
›
Push in the interlocks on the cover and lock.

Assignment of fuses in the engine compartment
First read and observe the introductory information and safety warn-ings
on page 251.
No.Power consumer1Control unit for ESC, ABS2Control unit for ESC, ABS3Engine control unit4Engine control unit, relay for electric auxiliary heating5Engine components6Brake sensor, engine components7Coolant pump, engine components8Lambda probe9Ignition, control unit for glow plug system, engine components10Control unit for fuel pump, ignition11Electrical auxiliary heating system12Electrical auxiliary heating system13Control unit for automatic gearbox14Not assigned15Horn16Ignition, fuel pump17Control unit for ABS, ESC, engine control unit18Data bus control unit19Windscreen wipers 254Do-it-yourself

No.Power consumer20Alarm21Windscreen heater - left22Engine control unit23Starter24Electrical auxiliary heating system31Not assigned32Not assigned33Not assigned34Windscreen heater - right35Not assigned36Not assigned37Control unit for auxiliary heating38Not assigned

Bulbs
Introduction
This chapter contains information on the following subjects:
Bulb arrangement in the headlights
256
Replacing the low beam bulb
256
Replacing bulb for main beam and daytime running lights
256
Replacing bulb for daytime running lights and parking lights
257
Change bulb for additional parking light
257
Replacing the bulb for the fog lights
258
Replacing the bulb for the licence plate light
258
Rear light (Octavia)
259
Replacing bulbs in rear light (Octavia)
260
Rear light (Octavia Estate)
261
Replacing bulbs in rear light (Octavia Estate)
262
Some manual skills are required to change a bulb. For this reason, we recommend
having bulbs replaced by a specialist garage or seeking other expert help in the
event of any uncertainties.
› Switch off the ignition and all of the lights before replacing a bulb.
› Faulty bulbs must only be replaced with the same type of bulbs. The designa-
tion is located on the light socket or the glass bulb.
› A stowage compartment for replacement bulbs is located in a plastic box in the
spare wheel or underneath the floor covering in the luggage compartment.WARNING■ Always read and observe the warnings before completing any work in the
engine compartment » page 215.■
Accidents can be caused if the road in front of the vehicle is not sufficiently
illuminated and the vehicle cannot or can only be seen with difficulty by other
road users.
■
Bulbs H7 H8 and H15 are pressurised and may burst when changing the bulb
- risk of injury! We therefore recommended wearing gloves and safety glasses when changing a bulb.
■
Gas discharge bulbs (xenon bulbs) operate with a high voltage, professional
knowledge is required – risk of death!
■
The relevant lamp must always be switched off before a light bulb is re-
placed.
CAUTION
Do not take hold of the glass bulb with naked fingers (even the smallest amount of dirt reduces the working life of the light bulb). Use a clean cloth, napkin, or sim-
ilar.
Note
■ This Owner's Manual only describes the replacement of bulbs where it is possi-
ble to replace the bulbs on your own without any complications arising. Other bulbs must be replaced by a specialist garage.■
We recommend that a box of replacement bulbs always be carried in the vehi-
cle. Replacement bulbs can be purchased from ŠKODAOriginal Accessories.
■
We recommend having the headlight settings checked by a specialist garage af-
ter replacing a bulb in the main beam, low beam or fog lights.
■
In case of failure of a xenon gas discharge lamp or an LED diode, visit a special-
ist garage.

255Fuses and light bulbs

Bulb arrangement in the headlightsFig. 220
Principle sketch: Headlight with halogen bulb/with Xenon bulb
Fig. 221
Principle sketch: Headlights with
Xenon headlights and LED day-
time running lights
First read and observe the introductory information and safety warn-
ings on page 255.
Headlight with halogen bulb
Low beam
Main beam, separate daytime running lights, and parking light
Headlights with Xenon light
Xenon gas discharge bulbs
Daytime running and parking light
Headlights with Xenon headlights and LED daytime running lights Xenon gas discharge bulbs
additional parking light

123456Replacing the low beam bulbFig. 222
Headlight with halogen bulb:
Bulb for low beam
First read and observe the introductory information and safety warn-
ings on page 255.
›
Remove the rubber cover
1
» Fig. 220 on page 256.
›
Turn the connector with the bulb in downwards in the direction of the arrow
A
» Fig. 222 and remove it in the direction of the arrow
B
.
›
Remove the connector.
›
Insert a new light bulb in such a way that the fixing lugs of the bulb fit in the
recesses of the reflector.
›
Attach the connector.
›
Insert the rubber cover
1
.

Replacing bulb for main beam and daytime running lights
Fig. 223
Headlight with halogen bulb: Re-
placing the bulb for main beam
and separate daytime running
lights
First read and observe the introductory information and safety warn- ings on page 255.
›
Remove the rubber cover
2
» Fig. 220 on page 256. 
256Do-it-yourself

›Turn the bulb holder A
» Fig. 223 as far as it goes in the direction of the arrow
and remove it.›
Replace the bulb, insert the bulb holder with the new bulb and turn in the oppo-
site direction to that of the arrow as far as it goes.
›
Insert the rubber cover
2
.

Replacing bulb for daytime running lights and parking lights
Fig. 224
Headlights with Xenon light:
Changing the bulb for daytime
running lights and parking light
First read and observe the introductory information and safety warn-
ings on page 255.
›
Remove the rubber cover
4
» Fig. 220 on page 256.
›
Turn the bulb holder
B
» Fig. 224 as far as it goes in the direction of the arrow
and remove it.
›
Replace the bulb, insert the bulb holder with the new bulb and turn in the oppo-
site direction to that of the arrow as far as it goes.
›
Insert the rubber cover
4
.

Change bulb for additional parking lightFig. 225
Headlights with Xenon headlights and LED daytime running lights:
Bulb for additional parking light
First read and observe the introductory information and safety warn-
ings
on page 255.
Removing/replacing the bulb for the parking light
›
Remove the rubber cover
6
» Fig. 221 on page 256.
›
Remove the bulb holder with the bulb by jiggling it out in the direction of the
arrow
1
» Fig. 225 .
›
Grasp the lamp socket at the places marked by arrows.
›
Remove the faulty bulb from the holder in the direction of the arrow
2
.
›
Insert a new bulb in the bulb holder up to the stop.
›
Replace the bulb holder in the headlamp with the bulb.
›
Insert the rubber cover
6
.

257Fuses and light bulbs

Replacing the bulb for the fog lightsFig. 226
Front bumper: Remove the protective grille/fog light
Fig. 227
Replacing the light bulb
First read and observe the introductory information and safety warn-
ings on page 255.
Removing the protective grille
›
Undo the protective grille in the area of the arrow » Fig. 226 - 
using the
clamp for removing the wheel trims » page 236, Vehicle tool kit .
›
Remove the protective grille in the direction of the arrow
1
.
Changing light bulbs for fog lights
›
Use the screwdriver from the tool kit to unscrew the fog lamp » Fig. 226 -
 .
›
Unlock the fuse in the direction of the arrow
2
with the screwdriver.
›
Remove the headlight in the direction of the arrow
3
.
›
Remove the connector.
›
Turn bulb holder
A

» Fig. 227 in an anti-clockwise direction up to the stop and
remove.
› Insert the bulb holder with the new bulb into the headlight and turn
clockwise
as far as the stop.›
Attach the connector.
›
Replace the fog lamp by inserting it in the opposite direction of the arrow
3
» Fig. 226 and screw tight.
›
Insert the protective grille and carefully press it in.
The protective grille must engage firmly.

Replacing the bulb for the licence plate light
Fig. 228
Remove the number plate light/replace the bulb
First read and observe the introductory information and safety warn- ings
on page 255.
›
Open the luggage compartment lid.
›
Push in the lamp in the direction of the arrow
1
» Fig. 228 .
The lamp comes loose.
›
Swivel out the lamp in the direction of the arrow
2
and remove it.
›
Remove the faulty bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb into the holder.
›
Reinsert the lamp in the opposite direction to the arrow
1
.
›
Push on the light until the spring clicks into place.
Check that the light is securely inserted.

258Do-it-yourself

Rear light (Octavia)Fig. 229
Remove cover / light
Fig. 230
Installing the lamp connector/lamp
First read and observe the introductory information and safety warn-
ings
on page 255.
Removing
›
Open the boot lid.
›
Insert the clamp for removing the wheel trims » page 236, Vehicle tool kit into
the hole at the position indicated by the arrow » Fig. 229 - 
.
›
Remove the cover in the direction of the arrow » Fig. 229 - 
.
›
Use the screwdriver from the tool kit to unscrew the lamp » Fig. 229 - 
.
›
Grip the tail lamp and carefully remove it by jiggling it out in the opposite direc-
tion of travel.
›
Press together the interlocks on the connector in the direction of arrow
1
» Fig. 230 -
 .
›Carefully remove the connector from the tail lamp assembly in the direction of
the arrow 2.
Installing›
Insert the connector into the lamp and lock it securely.
›
Insert the lamp into the mounts in the body » Fig. 230 -  .
›
Carefully press the tail lamp into the body so that the bolts
1
» Fig. 231 on
page 260 on the lamp engage into the mounts in the body » .
Ensure that the cable bundle does not become pinched between the body and
the lamp.
›
Screw the tail lamp into place and install the cover.
›
Ensure that the cover engages firmly.
CAUTION
■ Ensure that the cable bundle does not become pinched between the body and
the lamp when it is being refitted – risk of damage to the electric installation and risk of water ingress.■
If you are not sure whether the cable bundle has become pinched, we recom-
mend that you have the light connection checked by a specialist garage.
■
Ensure that the vehicle paintwork and the tail lamp are not damaged when re-
moving and installing the tail lamp.

259Fuses and light bulbs

Replacing bulbs in rear light (Octavia)Fig. 231
Outer part of the light: Basic light/light with LED diodes
Fig. 232
Inner part of the light: Basic light/light with LED diodes
First read and observe the introductory information and safety warn-
ings
on page 255.
Outer part of the lamp
›
Turn the bulb holder
2
» Fig. 231 in an anti-clockwise direction and remove it
from the lamp housing.
›
Push the faulty bulb into the holder, turn in anti -clockwise direction up to the
stop and remove.
›
Insert a new bulb into the holder and turn in a clockwise direction to the the
stop.
›
Replace the holder with the bulb into the lamp housing and turn in a clockwise
direction to the stop.
Inner part of the light›Unscrew the lamp holder » Fig. 231 -  or  use the screwdriver from the car
tool kit, and remove the lamp holder from the tail light assembly.›
Turn the bulb holder anti-clockwise up to the stop and remove it from the lamp
housing » Fig. 231 -  respectively .
›
Replace the bulb, insert the holder with the bulb into the lamp housing and turn
in a clockwise direction to the stop.
›
Insert the bulb holder in the tail lamp assembly.
›
Screw on the lamp holder carefully.

260Do-it-yourself

Rear light (Octavia Estate)Fig. 233
Remove cover / light
Fig. 234
Installing the lamp connector/lamp
First read and observe the introductory information and safety warn-
ings
on page 255.
Removing
›
Open the boot lid.
›
Insert the clamp for removing the wheel trims » page 236, Vehicle tool kit into
the hole at the position indicated by the arrow » Fig. 233 - 
.
›
Remove the cover in the direction of the arrow » Fig. 233 - 
.
›
Use the screwdriver from the tool kit to unscrew the lamp » Fig. 233 - 
.
›
Grip the tail lamp and carefully remove it by jiggling it out in the opposite direc-
tion of travel.
›
Press together the interlocks on the connector in the direction of arrow
1
» Fig. 234 -
 .
›Carefully remove the connector from the tail lamp assembly in the direction of
the arrow 2.
Installing›
Insert the connector into the lamp and lock it securely.
›
Insert the lamp into the mounts in the body » Fig. 234 -  .
›
Carefully press the tail lamp into the body so that the bolts
1
» Fig. 235 on
page 262 on the lamp engage into the mounts in the body » .
Ensure that the cable bundle does not become pinched between the body and
the lamp.
›
Screw the tail lamp into place and install the cover.
›
Ensure that the cover engages firmly.
CAUTION
■ Ensure that the cable bundle does not become pinched between the body and
the lamp when it is being refitted – risk of damage to the electric installation and risk of water ingress.■
If you are not sure whether the cable bundle has become pinched, we recom-
mend that you have the light connection checked by a specialist garage.
■
Ensure that the vehicle paintwork and the tail lamp are not damaged when re-
moving and installing the tail lamp.

261Fuses and light bulbs