2009 SUBARU TRIBECA lock

CS-21
Select Lever
CONTROL SYSTEMS
6) Remove the indicator lamp and then remove the
bulb.
7) Remove the shift lock solenoid assembly.
8) Remove the indicator assembly.
9) Remove the bulb case.
10) Remove the plate lamp guide.
11) Remove the position plate.
12) Remove the blind assembly.
CS-00612
CS-00613
CS-00614
CS-00615
CS-00616
ST-00617
CS-00618

CS-22
Select Lever
CONTROL SYSTEMS
13) Remove blind A and B.
14) Remove the clip while being careful not to
break the pin, and remove all switches.
15) Remove the connector from the base assembly
using a flat-tip screwdriver.
16) Remove all terminals from the connectors us-
ing a flat-tip screwdriver.
17) Remove the shift lock solenoid from the lock le-
ver bracket.
18) Remove the bushing.
19) Remove the lock lever bushing.
(A) Blind A
(B) Blind B
(A) Shift-up switch
(B) Shift-down switch
(C) “P” range switch
CS-00619
(A)
(B)
CS-00620
(A)(B)
(C)
CS-00621
CS-00622
5432112 11 10 9876
CS-00623
CS-00624
CS-00645

CS-23
Select Lever
CONTROL SYSTEMS
20) Remove the lock lever.
21) Remove the release rod and spring.
22) Remove the cable bracket.
23) Remove the spacer.
24) Remove the dust cover and dust cover bracket.
25) Remove the spacer.
26) Using a press, remove the shift position pin.
27) Remove the clips, then remove the shaft.
28) Remove the arm assembly.
CS-00625
CS-00626
CS-00627
CS-00628
(A) Dust cover
(B) Dust cover bracket
CS-00629
(B)(A)
CS-00630
CS-00631
CS-00632

CS-24
Select Lever
CONTROL SYSTEMS
29) Remove the bushing.
30) Remove the selector arm assembly.
31) Remove the clip while being careful not to
break the pin, then remove the shift button switch.
32) Remove the select shaft.
33) Remove the tube cross plate.
34) Remove the mode change switch.
35) Remove the detent check block.
CS-00634
CS-00635
CS-00636
CS-00637
CS-00638
CS-00639
CS-00640

CS-25
Select Lever
CONTROL SYSTEMS
D: ASSEMBLY
1) Clean all the parts before assembly.
2) Apply grease [Multemp AC-D, and SH-W or
equivalent] to each part. LECT LEVER, COMPONENT, General Descrip-
tion.>
3) Assemble in the reverse order of disassembly.
NOTE:
•Refer to “COMPONENT” for each tightening
torque. PONENT, General Description.>
•When pressing in the shift position pin, insert
from the left side of the vehicle.
•Affix the harness of the shift button switch and
the mode change switch at the marked positions.
•Connect the terminals of all switches to the re-
spective connectors.
4) After completing installation, shift the select le-
ver from the “P” range to the “D” range, then check
whether or not the selection indicator in the combi-
nation meter and the select lever position matches.
Also check whether the pointer and position mark
matches, and what the operating force is.
E: INSPECTION
1) Inspect the removed parts by comparing with
new ones for deformation, damage and wear. Re-
pair or replace if defective.
2) Confirm the select lever operating condition be-
fore assembly. Normal if it operates smoothly. CS-00641
(A) Mode change switch (color code: Yellow)
(B) Shift button switch (color code: Brown)
(C) Mode change switch and shift button switch
ground (color code: White)
(D) Shift up switch (color code: Green)
(E) Shift up switch (color code: Gray)
(F) Shift up/down switch ground (color code: Blue)
(G) “P” range switch (wire color: Red)
(H) Shift lock solenoid (color code: Blue)
(I) Shift lock solenoid (color code: Black)
(J) Indicator lamp (color code: Blue)
CS-00642
5432112 11 10 9876
(J)
(J)(F)(E)(D)(A)(B)(C)
(H) (G)(I)

CS-27
Select Cable
CONTROL SYSTEMS
3) Install the plate assembly to transmission.
Tightening torque:
24.5 N·m (2.5 kgf-m, 18.1 ft-lb)
4) Install the washer and snap pin to range select
lever.
5) Install new clamp paying attention to the install-
ing direction.
6) Insert the tip of inner cable into connector hole of
select lever, and fix the cable to bracket.
7) Shift the select lever to the “N” range, and then
adjust the select cable position. ADJUSTMENT, Select Cable.>
8) Install the heat shield cover.
9) Install the front, center and rear exhaust pipe,
and the muffler. TION, Front Exhaust Pipe.> INSTALLATION, Rear Exhaust Pipe.> EX(H6DO)-8, INSTALLATION, Muffler.>
C: INSPECTION
Check the removed cable and replace or adjust if
damaged, rusty or malfunctioning.
1) Check the cable for smooth operation.
2) Check the inner cable for damage and rust.
3) Check the outer cable for damage, bends and
cracks.
4) Check the boot for damage, cracks and deterio-
ration.
5) Move the select lever from “P” to “D” range.
Check the existence of feel to contact the detents in
each range. If the detents cannot be felt or the po-
sition pointer is improperly aligned, adjust the ca-
ble.
6) Check if the starter motor rotates when the se-
lect lever is set to “P” range.
7) Check the back-up light illumination when the
select lever is in “R” range.
8) Check the parking lock operation when the se-
lect lever is in “P” range.
9) Check that the AT shift lock system operates
normally.
(A) Select cable
(B) Plate ASSY
(A) Range select lever
(B) Snap pin
(C) Select cable
(D) Bracket
(E) Washer
(A) Clamp
(B) Forward
(A)
(B)CS-00328
CS-00327
(B)
(D)
(C)
(E)
(A)
CS-00643
(A)
(B)
C
C
CS-00535

CS-29
AT Shift Lock Solenoid and “P” Range Switch
CONTROL SYSTEMS
5. AT Shift Lock Solenoid and
“P” Range Switch
A: REMOVAL
NOTE:
For removal of the mode change switch and the
shift button switch, refer to the section on Select
Levers. Lever.>
1. “P” RANGE SWITCH
1) Remove the console box. MOVAL, Console Box.>
2) Disconnect the connector.
3) Remove the connector from the base plate using
a flat-tip screwdriver.
4) Disconnect the terminal of “P” range switch from
connector, using a flat-tip screwdriver with thin tip.
5) Remove the clip while being careful not to break
the pin, then remove the “P” range switch.
2. AT SHIFT LOCK SOLENOID
1) Remove the console box. MOVAL, Console Box.>
2) Disconnect the connector.
3) Remove the connector from the base plate using
a flat-tip screwdriver.
4) Remove the AT shift lock solenoid.
(A) “P” range switch
CS-00621
CS-00646
5432112 11 10 9876
(A)
(A) “P” range switch
CS-00647
(A)
CS-00621
CS-00648

CS-30
AT Shift Lock Solenoid and “P” Range Switch
CONTROL SYSTEMS
5) Disconnect the terminal of AT shift lock solenoid
from the connector, using a flat-tip screwdriver.
B: INSTALLATION
NOTE:
For installation of the mode change switch and the
shift button switch, refer to the section on Select
Levers. ver.>
1. “P” RANGE SWITCH
Install in the reverse order of removal.
NOTE:
Connect the “P” range switch terminal to connector.
2. AT SHIFT LOCK SOLENOID
Install in the reverse order of removal.
NOTE:
Connect the AT shift lock solenoid switch terminal
to connector.
(A) AT shift lock solenoid
(A) “P” range switch (wire color: Red)
CS-00649
5432112 11 10 9876
(A)
CS-00646
5432112 11 10 9876
(A)
(A) AT shift lock solenoid (color code: Black)
(B) AT shift lock solenoid (wire color: Blue)
CS-00651
5432112 11 10 9876
(A) (B)