2007 TOYOTA SIENNA differential

DF–34DIFFERENTIAL – REAR DIFFERENTIAL CARRIER
DF
(e) Install the carrier cover with the 8 bolts.
Torque: 47 N*m (475 kgf*cm, 34 ft.*lbf)
C098113

SUSPENSION – REAR COIL SPRINGSP–41
SP
REMOVAL
1. REMOVE REAR WHEEL
2. REMOVE SKID CONTROL SENSOR WIRE (for 2WD)
(a) Disconnect the skid control sensor connector.
(b) Remove the bolt and disconnect the bracket from
the rear axle beam assembly.
HINT:
Separate the RH side by the same procedures as
the LH side.
3. SEPARATE SPEED SENSOR REAR LH (for 4WD)
(a) Remove the bolt and speed sensor rear LH.
4. SEPARATE SPEED SENSOR REAR RH (for 4WD)
HINT:
Separate the RH side by the same procedures as the LH
side.
5. REMOVE EXHAUST PIPE ASSEMBLY TAIL
HINT:
• 2WD DRIVE TYPE (See page EX-2)
• 4WD DRIVE TYPE (See page EX-8)
6. REMOVE PROPELLER W/CENTER BEARING SHAFT
ASSEMBLY (for 4WD)
HINT:
(See page PR-2)
7. SEPARATE REAR DRIVE SHAFT ASSEMBLY LH (for
4WD)
(a) Place matchmarks on the rear drive shaft assembly
LH and differential flange.
(b) Remove the 4 nuts and 4 washers, separate rear
drive shaft assembly LH.
8. SEPARATE REAR DRIVE SHAFT ASSEMBLY RH (for
4WD)
HINT:
Separate the RH side by the same procedures as the LH
side.
9. REMOVE DIFFERENTIAL CARRIER ASSEMBLY
REAR (for 4WD)
HINT:
(See page DF-8)
G023899
G023898
G023905E01

SP–46SUSPENSION – REAR COIL SPRING
SP
(c) Install the bolt.
Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)
6. CONNECT REAR BRAKE TUBE NO.1
SST 09023-00101
HINT:
Connect the RH side by the same procedures as the LH
side.
7. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3
(a) Install the 2 bolts and parking brake cable assembly
No.3 to the rear axle beam assembly.
Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)
8. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.2
HINT:
Install the RH side by same procedures as the LH side.
9. INSTALL DIFFERENTIAL CARRIER ASSEMBLY
REAR (for 4WD)
HINT:
(See page DF-8)
10. INSTALL REAR DRIVE SHAFT ASSEMBLY LH (for
4WD)
(a) Install the rear drive shaft assembly LH, 4 washers
and 4 nuts.
Torque: 56 N*m (571 kgf*cm, 41 ft.*lbf)
11. INSTALL REAR DRIVE SHAFT ASSEMBLY RH (for
4WD)
HINT:
Install the RH side by same procedures as the LH side.
12. INSTALL PROPELLER W/CENTER BEARING SHAFT
ASSEMBLY (for 4WD)
HINT:
(See page PR-2)
C088688
G023904
G023905E01

SUSPENSION – REAR AXLE BEAMSP–57
SP
REMOVAL
1. REMOVE REAR WHEEL
2. REMOVE SKID CONTROL SENSOR WIRE (for 2WD)
HINT:
(See page SP-38)
HINT:
Disconnect the RH side by the same procedures as the
LH side.
3. SEPARATE SPEED SENSOR REAR LH (for 4WD)
HINT:
(See page SP-38)
4. SEPARATE SPEED SENSOR REAR RH (for 4WD)
HINT:
Separate the RH side by the same procedures as the LH
side.
5. REMOVE EXHAUST PIPE ASSEMBLY TAIL
HINT:
• 2WD DRIVE TYPE (See page EX-2)
• 4WD DRIVE TYPE (See page EX-8)
6. REMOVE PROPELLER W/CENTER BEARING SHAFT
ASSEMBLY (for 4WD)
HINT:
(See page PR-2)
7. REMOVE REAR AXLE SHAFT LH NUT (for 4WD)
HINT:
(See page AH-18)
8. REMOVE REAR AXLE SHAFT RH NUT (for 4WD)
HINT:
Remove the RH side by the same procedures as the LH
side.
9. REMOVE REAR DRIVE SHAFT ASSEMBLY LH (for
4WD)
HINT:
(See page AH-18)
10. REMOVE REAR DRIVE SHAFT ASSEMBLY RH (for
4WD)
HINT:
Remove the RH side by the same procedures as the LH
side.
11. REMOVE DIFFERENTIAL CARRIER ASSEMBLY
REAR (for 4WD)
HINT:
(See page DF-8)
12. SEPARATE PARKING BRAKE CABLE ASSEMBLY
NO.3
HINT:
(See page SP-38)

SUSPENSION – REAR AXLE BEAMSP–63
SP
20. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
LH (for DISC REAR BRAKE)
(a) Install the 2 bolts and rear disc brake caliper
assembly LH to the rear axle beam assembly.
Torque: 88 N*m (897 kgf*cm, 65 ft.*lbf)
21. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
RH (for DISC REAR BRAKE)
HINT:
Install the RH side by the same procedures as the LH
side.
22. CONNECT REAR BRAKE TUBE NO.2
HINT:
(See page SP-38)
SST 09023-00101
23. CONNECT REAR BRAKE TUBE NO.1
SST 09023-00101
HINT:
Connect the RH side by the same procedures as the LH
side.
24. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3
HINT:
(See page SP-38)
25. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.2
HINT:
Install the RH side by the same procedures as the LH
side.
26. INSTALL DIFFERENTIAL CARRIER ASSEMBLY
REAR (for 4WD)
HINT:
(See page DF-8)
27. INSTALL REAR DRIVE SHAFT ASSEMBLY LH (for
4WD)
HINT:
(See page AH-18)
28. INSTALL REAR DRIVE SHAFT ASSEMBLY RH (for
4WD)
HINT:
Install the RH side by the same procedures as the LH
side.
29. INSTALL REAR AXLE SHAFT LH NUT (for 4WD)
HINT:
(See page AH-18)
30. INSTALL REAR AXLE SHAFT RH NUT (for 4WD)
HINT:
Install the RH side by the same procedures as the LH
side.
31. INSTALL PROPELLER W/CENTER BEARING SHAFT
ASSEMBLY (for 4WD)