2006 GREAT WALL DEER Service Manual

B0-58
Safety belt (
)
Element figure
Vehicle Body
Safety Belt
QP
43
QP
43
43
43
43
safety belt in
SY model
vehicle
43
safety belt in SJ
model vehicle
N
m
specified torque

B0-59Body
Safety Belt
Safety belt
1. Driving test (in the security place);
(a) Fix the safety belt of the front seat.
(b) Drive the vehicle at the speed of 16 km/h and brake it
suddenly;
(c) Check the safety belt, which should be lock tightly
without expansion.
Remark: it is required to tear down the mechanism
fittings of the safety belt to make the following static load
test at the security place, in addition, moderate inspection
for the new safety belt should be conducted before
mounting no matter when the new safety belt fittings is
needed to mount.
2. Static test

a) Tear down the lock-type expansion fittings;
(b) Tilt the expansion fittings slowly;
(c) Check the expansion of safety belt, which should be
pulled out when the tilt angle is no more than 15 but not
be pulled out when the tilt angle is more than 45
.
If the requirement is not met, change the safety belt fittings.
Two-point safety belt
(manually operated)
(a) Adjust the safety belt to the moderate length;
(b) Exert the stable load on the belt;
(c) Check whether the safety belt is elongated or not, in such
case, the belt should not be elongated.

B0-60
Seat (
)
Element figure
Vehicle Body
Seat
Dr SL SK SF SY SJ
front seat
seat in SY
model vehicle
N
m
specified torque
37
37
37
37
18
18
18
18

B0-61
Safety belt (
)
Element figure
Vehicle Body
Safety Belt
Dr rear seat
SL rear seat
N
m
specified torque
18
18
18
18
18
SY small seat18
18
18

B0-62
Seat (
)
Element figure
Body
Seat
SF rear seat
18
18
18
18
18
18
18
SJ rear seat
N
m
specified torque
18

B0-63
Spoiler (
)
Element figure
Vehicle Body
Spoiler
Dismantle of Spoiler
1. Tear down the spoiler assembly;
(a) Tear down the four bolts and the spoiler;
(b) Tear down the three bolts and the spoiler supporter.
2. Tear down the wire harness of highly-mounted stop-
grade lamp and take it down;
Mount of spoiler
Mount the spoiler in the reverse approach. SF
spoiler
spoiler supporter highly mounted stop-grade lamp

B0-64
Spoiler (
)
Element figure
Vehicle Body
Spoiler
Spoiler disassembly
1. Tear down the highly-mounted stop-grade lamp;
(a) Tear down the two screws and disconnect the wire harness
from lamp.
(b) Tear down the highly-mounted stop lamp from the spoiler.
2. Tear down the spoiler assembly
(a) Tear down the rear beam trim panel from the inside of body.
(b) Tear down the four nuts and disconnect the wire harness
from the spoiler;
(c) Tear down the spoiler assembly and spoiler gasket from the
outside.
SJ
(a) Open the two covers of round hole at the top-grade of
spoiler;
(b) Tear down the two bolts and disconnect the wire harness
from the spoiler.
(c) Tear down the spoiler assembly and spoiler gasket from the
outside.
Mount of Spoiler
Mount the spoiler in the reverse approach.
SY SJ
spoiler gasketnuthighly mounted
stop lampspoiler
assembly

B0-65
Luggage rack
Element figure
Vehicle Body
Luggage Rack
bracket fastening
buttonmain sill
SF SY
antiskid strip
beamblanking plug of
main sill adjusting button of antiskid strip
fixed bracket
mounting plate of outer
luggage rack
adhesive strip of mounting plateluggage rack assembly
SJ