2006 GREAT WALL DEER Service Manual

SR-1
Notice .......................................................................... SR-2
Troubleshooting .......................................................... SR-2
Inspection on Vehicle .................................................. SR-3
Steering Column ......................................................... SR-4
Manual Steering Gear ................................................. SR-9
Power Steering ............................................................ SR-11
General Introduction ................................................ SR-11
Inspection on vehicle ............................................... SR-13
Power Steering Oil Pump ........................................ SR-16
Power Steering Gear ............................................... SR-18
Steering linkage .......................................................... SR-20
SR
Steering System
Page

SR-2
Notice
The parts change should be conducted correctly because
any error will affect the properties of steering system, or lead
to accidental or damage when driving.
Troubleshooting
Trouble Causes Inspection items
Unsuitable tire inflation
Insufficient lubricant
Over-large inclination
Steering gear joint wear
Lower swing arm ball head wear
Steering column seize-up
Steering gear unsuitable adjustment or damage
Power steering conveyer looseness
Over-low liquid level in oil cup of steering pump
Failure in power steering mechanismInflate the tire to specified pressure
Lubricating the hanging devices
Check the Alignment of Front Wheel
Change the Steering gear joint
Change the lower swing arm ball
head;
Check the steering column
Adjust or repair the gear.
Adjust the conveyor.
Check the steering pump oil cup
Check the power steering devices
Poor returning
Unsuitable tire inflation
Insufficient lubricant
Incorrect wheel alignment
Steering column seize-up
Steering gear unsuitable adjustment or damageInflate the tire to specified pressure
Lubricating the hanging devices.
Check the Alignment of Front
Wheel
Check the steering column
Change the steering gear.
Over-large playFront wheel bearing wear
Steering drive shaft yoke wear
Lower swing arm ball head wear
Steering gear joint wear
Steering gear unsuitable adjustment or damageChange the front bearing
Change the steering drive shaft
Change the swing arm ball head
Change the steering gear joint
Change the steering joint
Abnormal noise
Steering drive lever looseness
Steering gear joint wear
Steering gear unsuitable adjustment or damage
Oil lack or poor sealing of steering machine.Tighten the steering drive lever
Change the steering gear joint
Change the steering gear
Add the oil or change the sealing
washer Steering system inspection
on vehicle.
Steering System
Notice and Troubleshooting
Difficulty in steering

SR-3Steering System
On-vehicle Inspection
max play
On-vehicle Inspection
Steering wheel play
1.SR-18Check to see whether the steering wheel play is
correct;
Park the vehicle stably and align the tires in correct direction,
press the steering wheel with finger and swing it in left and
right direction. The play should not exceed the max play.
(Max play)
6
(Dr SF)
If the play is nor correct, adjust or repair the steering wheel as
requirement.
2. Adjust the steering wheel play:
(a) Align the wheel forward precisely;
(b) Loosen the locking nuts of steering gear;
(c) Rotate the adjusting screws of steering gear clockwise to
reduce the steering wheel play, while contrarotate the
adjusting screws to increase the steering wheel play.
Remark: screw the adjusting screws and enlarge the play a
little each time to check the adjusted play.
3. Check to see whether there is steering inconvenience
Rotate the steering wheel by half round in right and left
direction to check whether the play is correct, and whether the
wheel runs smoothly or any seize-up in its running.
4. Fix the adjusting screws and fasten the adjustable nut.
Oil level height
Check the oil level height in the steering gear housing.
Oil level height: flush with the filler opening.
If there oil is insufficient, add the gear oil and check to see
whether there is oil leakage.

SR-4Steering System
Steering Column
Steering Column
Element figure of non-adjustable steering column
Dr
SL SK SY
upper part of
steering column
steering drive shaft
30
2
N
m
specified torque
steering drive shaftupper part of steering column
50
5
universal cardan joint
dust cap
fixed support seat

SR-5
Steering Column
Element figure of adjustable steering column
Steering System
Steering Column
Dr SF
upper part of steering column
universal cardan joint
steering drive
shaft
upper part of steering column
steering drive shaftuniversal cardan joint
universal cardan jointsteering column
SL SK SY
SJ

SR-6Steering System
Steering Column
Dismantle of the steering wheel
1. Dismantle of the steering wheel;
(a) Take down the bugle cap;
(b) Pull down the bugle wire.
(c) Tear down the fixing nut of steering wheel.
2. Tear down the combined switch cover;
3. Tear down the cover at left bottom part.
4. Tear down the fixing bracket for the left-bottom cover.
5. Tear down the air passage;
6. Tear down the combined switch;
7. Tear down the fixed support seat bolts on front-wall panel;
8. Tear down the fixing bolts at upper part of steering
column, and
9. Tear down the connecting bolts of steering column
drive shaft.
10. Pull out the steering column.

SR-7
Mount of Steering Column
1. Mount the ignition switch assembly
Fix the ignition switch on the steering column with SST.
2. Mount the dust cap and fixed support seat of steering
column on the front-wall panel.
3. Mount the upper part of steering column;
Mount the upper part of steering column on the fixed bracket
with SST.
4. Connect the upper part of steering column and the
steering drive shaft with the universal cardan joint;
5. Connect the steering drive shaft and the steering gear;
6. Mount the combined switch.
Fix the combined switch with SST.
7. Mount the combined switch cover;
Fix the combined switch cover with SST.
Steering System
Steering Column
SST
SST
SST
SST

SR-8
8. Mount the steering wheel:
(a) Screw up the fixing nuts of steering wheel according to
the specified torque.
Specified torque
Dr SF
(50
5)N.m
SL SK SY SJ
(30
2)N
m
(b) Connect the bugle wire;
(c
Mount the bugle cap.
Steering System
Steering Column