2006 ACURA CSX rear seat

Î
(#'
)
20-116Seats
Component Location Index
REAR SEAT
FRONT SEAT
(Driver’s)
FRONT SEAT
(Passenger’s) Removal/Installation, page 20-131
Seat-back Latch Replacement, page 20-135
Seat-back Release Lever/Cable
Removal/Installation, page 20-136
Armrest Beverage Holder Replacement, page 20-137
Armrest Replacement, page 20-138
Seat-back Cover Replacement, page 20-139
Seat Side Bolster Cover Replacement, page 20-143
Seat Cushion Cover Replacement, page 20-143
Armrest Cover Replacement, page 20-144
Active Head Restraint Inspection, page 20-117
Removal/Installation, page 20-118
Seat Frame Replacement, page 20-122
Seat-back Cover Replacement, page 20-123
Seat Cushion Cover Replacement, page 20-127
Active Head Restraint Inspection, page 20-117
Removal/Installation, page 20-118
Seat Frame Replacement, page 20-120
Seat-back Cover Replacement, page 20-123
Seat Cushion Cover Replacement, page 20-127
08/08/21 15:03:05 61SNR030_200_0118
ProCarManuals.com
DYNOMITE -2009-




Passenger’s seat
Driver’s seat
20-119
Fastener Locations
:Bolt,2
10x1.25mm
Fastener Locations :Bolt,2
10x1.25mm A
B C
D
F
A
A B
C
D E
A
6. Remove the rear seat track bolts.
7. Slide the front seat rearward fully, and remove the
front seat track bolts. 8. Lift up the front seat, then detach the harness clips
(A), and disconnect the side airbag connector (B),
the seat belt switch connector (C), and the seat belt
buckle tensioner connector (D). On the driver’s seat,
disconnect the seat heater subharness connector
(E) or the seat position sensor connector. On the
passenger’s seat, disconnect the seat heater
subharness connector (F) or the ODS unit
subharness connector.
(cont’d)
08/08/21 15:03:54 61SNR030_200_0121
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
Seat-back
20-131
Rear Seat Removal/Installation
Fastener Locations B
:Bolt,3
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
C
D E
A
B
C EFastener Location
:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) A
B
A
NOTE: Take care not to scratch the body or tear the seat
covers. 1. Remove the right seat-back (A). –1 Fold the right seat-back down.
–2 Release the Velcro fasteners (B), and pull backthe seat-back cover (C), then remove the bolts.
–3 Release the hooks (D) of the pivot bracket (E). 2. Remove the bolt, then remove the center pivot
bracket (A).
3. If necessary, remove the bushing (B).
(cont’d)
08/08/21 15:04:02 61SNR030_200_0133
ProCarManuals.com
DYNOMITE -2009-



20-132Seats
Rear Seat Removal/Installation (cont’d)
Fastener Location
:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) FG
H
A B
C
D
E
B A
B
C
D
A
B
Front
4. Remove the left seat-back (A). –1 Fold the left seat-back down.
–2 Pull the rear center seat belt (B) out through theslit (C) in the seat belt guide (D).
–3 Release the Velcro fastener (E), and pull back the seat-back cover (F), then remove the bolt.
–4 Release the hooks (G) of the pivot bracket (H). 5. Extend the rear center seat belt (A) to remove the
left seat-back (B), then release the pivot shaft (C)
from the center pivot bracket (D).
6. If necessary, remove the bushing (A) from the center pivot bracket (B).
08/08/21 15:04:03 61SNR030_200_0134
ProCarManuals.com
DYNOMITE -2009-


Seat Cushion
20-133
Fastener Location:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A 6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A B
Fastener Location
:Bolt,1
7. Remove the seat cushion and seat side bolster.
8. Remove the bolt, then remove the pivot bracket (A).
9. Install the seat-back in the reverse order of removal, and note these items:
 Guide the belt over the front of the seat-back as you install the seat-back.
 Before attaching the rear seat-back, make sure there are no twists or kinks in the rear center seat
belt. NOTE: Take care not to scratch the body or tear the seat
covers.
1. Remove the bolt between the seat-back (A) and the seat cushion (B).
(cont’d)
08/08/21 15:04:03 61SNR030_200_0135
ProCarManuals.com
DYNOMITE -2009-

Î

Seat Side Bolster
20-134Seats
Rear Seat Removal/Installation (cont’d)
C
D
E
C C
F
B
A
Fastener Location
:Bolt,1
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
2. While pushing down on the seat cushion (A), pullthe seat hook handles (B) to release the hooks (C).
3. Pull back the seat cushion to release the center seat belt (D) and seat belt buckles (E) from their slits (F),
and remove it.
4. Install the seat cushion in the reverse order of removal, and note these items:
 Before attaching the seat cushion, make sure there are no twists or kinks in the seat belts.
 When installing the seat cushion, slip the seat belt buckles through the slits in the seat cushion. NOTE: Take care not to scratch the body or tear the seat
covers.
1. Remove the seat cushion.
2. Remove the bolt.
08/08/21 15:04:03 61SNR030_200_0136
ProCarManuals.com
DYNOMITE -2009-




(#'

 )
20-13520-135
Rear Seat-back Latch Replacement
A
B
B
A
B
A
B
Fastener Locations
A
:Bolt,2
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
3. Fold the seat-back down.
4. Lift the seat side bolster (A) up to release the hook(B), then remove the seat side bolster.
5. Install the side bolster in the reverse order of removal, and note these items:
 Guide the belts over the front of the seat side bolster as you install the bolster.
 Before attaching the seat side bolster, make sure there are no twists or kinks in the seat belts. NOTE: Take care not to bend or scratch the interior trim.
1. Remove the rear shelf (see page 20-78).
2. From the trunk compartment, disconnect the seat- back release cable (A) from the seat-back latch (B).
3. Remove the bolts, then remove the seat-back latch (A).
(cont’d)
08/08/21 15:04:04 61SNR030_200_0137
ProCarManuals.com
DYNOMITE -2009-




(#'

 )
20-13520-135
Rear Seat-back Latch Replacement
A
B
B
A
B
A
B
Fastener Locations
A
:Bolt,2
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
3. Fold the seat-back down.
4. Lift the seat side bolster (A) up to release the hook(B), then remove the seat side bolster.
5. Install the side bolster in the reverse order of removal, and note these items:
 Guide the belts over the front of the seat side bolster as you install the bolster.
 Before attaching the seat side bolster, make sure there are no twists or kinks in the seat belts. NOTE: Take care not to bend or scratch the interior trim.
1. Remove the rear shelf (see page 20-78).
2. From the trunk compartment, disconnect the seat- back release cable (A) from the seat-back latch (B).
3. Remove the bolts, then remove the seat-back latch (A).
(cont’d)
08/08/21 15:04:04 61SNR030_200_0137
ProCarManuals.com
DYNOMITE -2009-