2006 ACURA CSX rear seat



(#'
 )
20-13620-136 Seats
Rear Seat-back Latch Replacement
(cont’d)
Rear Seat-back Release Lever/Cable
Removal/Installation
Fastener Location
:Clip,1
A
B
4. Install the latch in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. NOTE: Take care not to bend or scratch the interior trim.
1. Open the trunk lid.
2. From the trunk compartment, detach the cable clip.
3. Disconnect the seat-back release cable (A) from the seat-back latch (B).
08/08/21 15:04:04 61SNR030_200_0138
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
20-13620-136 Seats
Rear Seat-back Latch Replacement
(cont’d)
Rear Seat-back Release Lever/Cable
Removal/Installation
Fastener Location
:Clip,1
A
B
4. Install the latch in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. NOTE: Take care not to bend or scratch the interior trim.
1. Open the trunk lid.
2. From the trunk compartment, detach the cable clip.
3. Disconnect the seat-back release cable (A) from the seat-back latch (B).
08/08/21 15:04:04 61SNR030_200_0138
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
Special Tools Required
20-13720-137
Rear Seat Armrest Beverage Holder
Replacement
A B
C
D
D
AB
C
D
4. Push the tab (A) to release the hook (B), and rotate the seat-back release lever (C) clockwise to release
the hook (D).
5. Install the release lever/cable in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. KTC trim tool set SOJATP2014
NOTE:
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to tear or damage the seat covers.
1. Using a trim tool, push on the bottom ribs (A) of the rear hooks (B) to pull up the beverage holder (C),
then release the hooks from the wire (D).
(cont’d)
08/08/21 15:04:05 61SNR030_200_0139
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
Special Tools Required
20-13720-137
Rear Seat Armrest Beverage Holder
Replacement
A B
C
D
D
AB
C
D
4. Push the tab (A) to release the hook (B), and rotate the seat-back release lever (C) clockwise to release
the hook (D).
5. Install the release lever/cable in the reverse order of removal, and note these items:
 Make sure the release cable is connected securely.
 Make sure the seat-back locks securely and unlocks properly. KTC trim tool set SOJATP2014
NOTE:
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to tear or damage the seat covers.
1. Using a trim tool, push on the bottom ribs (A) of the rear hooks (B) to pull up the beverage holder (C),
then release the hooks from the wire (D).
(cont’d)
08/08/21 15:04:05 61SNR030_200_0139
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
20-13820-138 Seats
Rear Seat Armrest Beverage Holder
Replacement (cont’d)
Rear Seat Armrest Replacement
A
B C
B A
B
A
B
C
2. Release the front hooks (A) from the wire (B), then
remove the beverage holder (C).
3. Install the beverage holder in the reverse order of removal. Make sure the front hooks are installed
securely to the wire, then push down on the
beverage holder and install the rear hooks into the
wire securely. NOTE: Take care not to tear the seams or damage the
seat covers.
1. Remove the clip (A) from the left portion of the armrest pivot (B).
2. Slide the armrest (A) toward the driver’s side of the vehicle, and remove the pivot shaft (B) from the
collar (C) on the right side of the vehicle by pulling
back on the armrest.
08/08/21 15:04:05 61SNR030_200_0140
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
20-13820-138 Seats
Rear Seat Armrest Beverage Holder
Replacement (cont’d)
Rear Seat Armrest Replacement
A
B C
B A
B
A
B
C
2. Release the front hooks (A) from the wire (B), then
remove the beverage holder (C).
3. Install the beverage holder in the reverse order of removal. Make sure the front hooks are installed
securely to the wire, then push down on the
beverage holder and install the rear hooks into the
wire securely. NOTE: Take care not to tear the seams or damage the
seat covers.
1. Remove the clip (A) from the left portion of the armrest pivot (B).
2. Slide the armrest (A) toward the driver’s side of the vehicle, and remove the pivot shaft (B) from the
collar (C) on the right side of the vehicle by pulling
back on the armrest.
08/08/21 15:04:05 61SNR030_200_0140
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
Seat-back
20-13920-139
Rear Seat-back Cover Replacement
A B
C
A B Fastener Location
A
:Screw,1
3. Remove the pivot shaft (A) from the collar (B) on
the left, then remove the armrest (C).
4. Remove the collars (A) from the seat-back (B).
5. Install the armrest in the reverse order of removal. NOTE:
 Take care not to tear the seams or damage the seat covers.
 Put on gloves to protect your hands.
1. Remove the seat-back (see page 20-131).
2. Remove these items:
 Armrest (see page 20-138)
 Head restraint
3. Left seat-back: Remove the screw, then remove the center belt guide (A).
(cont’d)
08/08/21 15:04:06 61SNR030_200_0141
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
Seat-back
20-13920-139
Rear Seat-back Cover Replacement
A B
C
A B Fastener Location
A
:Screw,1
3. Remove the pivot shaft (A) from the collar (B) on
the left, then remove the armrest (C).
4. Remove the collars (A) from the seat-back (B).
5. Install the armrest in the reverse order of removal. NOTE:
 Take care not to tear the seams or damage the seat covers.
 Put on gloves to protect your hands.
1. Remove the seat-back (see page 20-131).
2. Remove these items:
 Armrest (see page 20-138)
 Head restraint
3. Left seat-back: Remove the screw, then remove the center belt guide (A).
(cont’d)
08/08/21 15:04:06 61SNR030_200_0141
ProCarManuals.com
DYNOMITE -2009-