2006 ACURA CSX torque


µ
µ
Rear
Limited torque:
108 N·m (11.0 kgf·m, 79.6 lbf·ft) max.
18-11
A
B
D
F
E
C
07MAC-SL0A202 A
B
C
E G
F
D
11 14 mm
(0.43 0.55 in.)
1. Raise the vehicle, and support it with safety stands
in the proper locations (see page 1-11).
2. Remove the rear brake disc (see page 19-34).
3. Separate the wheel bolt (A) from the hub (B) using the ball joint remover (C), and keep the jaw (D) of
ball joint remover vertical against the wheel bolt
(see page 18-12).
NOTE: If the angle of the remover against the wheel bolt is not square, readjust the ball joint remover by
turning the head (E) of the adjusting bolt (F).
 Before installing the new wheel bolt, clean the mating surfaces on the bolt and the hub. 4. Insert the new wheel bolt (A) into the hub (B) while
aligning the splined surfaces (C) on the hub hole
with the wheel bolt. Adjust the measurement (D)
with washers (P/N 94101-12800 or equivalent) (E),
then install a nut (P/N 90304-SC2-000 or equivalent)
(F) hand-tight.
NOTE: Degrease all around the wheel bolt and the threaded section of the nut.
 Make sure the wheel bolt is installed vertically in relation to the hub disc surface.
 Do not install the nut and washers that have been used as tools on a vehicle.
5. Tighten the nut until the wheel bolt is drawn fully into the hub. Do not exceed the maximum torque
limit. Make sure there is no gap (G) between the
bolt and the hub.
6. Install the rear brake disc (see page 19-34). NOTE: If you cannot tighten the wheel nut to the specified torque value when installing the wheel,
replace the rear hub bearing unit as an assembly.
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
08/08/21 14:56:48 61SNR030_180_0011
ProCarManuals.com
DYNOMITE -2009-


Î 
18-16Front Suspension
Knuckle/Hub/Wheel Bearing Replacement (cont’d)
A
B
Except Type S model:
22x1.5mm
181 N·m
(18.5 kgf·m, 134 lbf·ft)
Type S model:
24x1.5mm
245 N·m
(25.0 kgf·m, 181 lbf·ft)
B
12x1.25mm
54 N·m
(5.5 kgf·m,
40 lbf·ft)
A
07MAC-SL0A20207AAF-SDAA100 D
12x1.25mm
59 N·m
(6.0 kgf·m,
43 lbf·ft)
B
12x1.25mm
59 N·m
(6.0 kgf·m, 43 lbf·ft)
C
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft) A
E
6. Raise the stake (A), then remove the spindle nut (B).
7. Remove the front brake disc (see page 19-21).
8. Check the front hub for damage and cracks.
9. Remove the cotter pin (A) from the tie-rod end ball joint, then remove the nut (B).
NOTE: During installation, install a new cotter pin
after tightening the nut, and bend its end as shown. 10. Disconnect the tie-rod end ball joint from the
knuckle using the ball joint thread protector and the
ball joint remover (see page 18-12).
11. Remove the flange bolt and the self-locking nuts from the lower arm (A).
NOTE: During installation, install the new flange
bolt and the new self-locking nuts. After lightly
tightening all three fasteners, tighten them to the
specified torque in the following order; the nut on
the front (B), the nut on the rear (C), then the bolt
(D).
12. Disconnect the lower ball joint (E) from the lower arm.
Replace.
Replace.
Replace. Replace.
Replace.
Replace.
08/08/21 14:56:50 61SNR030_180_0016
ProCarManuals.com
DYNOMITE -2009-



Wheel Bearing Replacement
18-18Front Suspension
Knuckle/Hub/Wheel Bearing Replacement (cont’d)
A
B
C
Except Type S model:
07GAF-SE00100
Type S model:
07GAF-SD40100
C Press
D D
A
B C
Except Type S model:
07GAF-SE00100
Type S model:
07GAF-SD40100
Press
17. Install the knuckle/hub in the reverse order of
removal, and note these items:
 First install all of the components, and lightly tighten the bolts and the nuts, then raise the
suspension to load it with the vehicle’s weight
before fully tightening to the specified torque
values.
 Be careful not to damage the ball joint boot when connecting the knuckle.
 Before connecting the lower ball joint to the knuckle, degrease the threaded section and the
tapered portion of the ball joint pin, the ball joint
connecting hole, the threaded section, and the
mating surfaces of the castle nut.
 Torque the castle nut to the lower torque specification, then tighten it only far enough to
align the slot with the ball joint pin hole. Do not
align the castle nut by loosening it.
 Use a new spindle nut during reassembly.
 Before installing the spindle nut, apply a small amount of engine oil to the seating surface of the
nut. After tightening, use a drift to stake the
spindle nut shoulder against the driveshaft.
 Before installing the brake disc, clean the mating surfaces of the front hub and the inside of the
brake disc.
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
18. Check the wheel alignment, and adjust it if necessary (see page 18-5). 1. Separate the hub (A) from the knuckle (B) using the
hub dis/assembly tool and a hydraulic press. Hold
the knuckle with the attachment (C) of the hydraulic
press or equivalent tool. Be careful not to damage
or deform the splash guard (D). Hold onto the hub
to keep it from falling when pressed clear.
2. Press the wheel bearing inner race (A) off of the hub (B) using the hub dis/assembly tool, a
commercially available bearing separator (C), and a
press.
08/08/21 14:56:51 61SNR030_180_0018
ProCarManuals.com
DYNOMITE -2009-






(#'
 ) Special Tools Required
18-2018-20 Front Suspension
Knuckle/Hub/Wheel Bearing
Replacement (cont’d)
Lower Ball Joint Replacement
D
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
C
A B
A
Press
07746-0010500
B 07749-0010000
C
07965-SD90100 B
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
C
12x1.25mm
59N·m(6.0kgf·m,43lbf·ft) A
D
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft) E
7. Install the snap ring (A) securely in the knuckle (B).
8. Install the splash guard (C), and tighten the screws
(D) to the specified torque value.
9. Install the hub (A) onto the knuckle (B) using the attachment, the driver handle, the support base,
and a hydraulic press. Be careful not to damage the
splash guard (C).  Ball joint remover, 32 mm 07MAC-SL0A102
 Ball joint thread protector, 14 mm 071AF-S3VA000
1. Remove the front wheel.
2. Remove the flange bolt and the self-locking nuts from the lower arm (A).
NOTE: During installation, install the new flange
bolt and the new self-locking nuts. After lightly
tightening all three fasteners, tighten them to the
specified torque in the following order; the nut on
the front (B), the nut on the rear (C), then the bolt
(D).
3. Disconnect the lower ball joint (E) from the lower arm.
Replace.
Replace.
Replace.
08/08/21 14:56:52 61SNR030_180_0020
ProCarManuals.com
DYNOMITE -2009-






(#'
 ) Special Tools Required
18-2018-20 Front Suspension
Knuckle/Hub/Wheel Bearing
Replacement (cont’d)
Lower Ball Joint Replacement
D
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
C
A B
A
Press
07746-0010500
B 07749-0010000
C
07965-SD90100 B
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
C
12x1.25mm
59N·m(6.0kgf·m,43lbf·ft) A
D
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft) E
7. Install the snap ring (A) securely in the knuckle (B).
8. Install the splash guard (C), and tighten the screws
(D) to the specified torque value.
9. Install the hub (A) onto the knuckle (B) using the attachment, the driver handle, the support base,
and a hydraulic press. Be careful not to damage the
splash guard (C).  Ball joint remover, 32 mm 07MAC-SL0A102
 Ball joint thread protector, 14 mm 071AF-S3VA000
1. Remove the front wheel.
2. Remove the flange bolt and the self-locking nuts from the lower arm (A).
NOTE: During installation, install the new flange
bolt and the new self-locking nuts. After lightly
tightening all three fasteners, tighten them to the
specified torque in the following order; the nut on
the front (B), the nut on the rear (C), then the bolt
(D).
3. Disconnect the lower ball joint (E) from the lower arm.
Replace.
Replace.
Replace.
08/08/21 14:56:52 61SNR030_180_0020
ProCarManuals.com
DYNOMITE -2009-


(#'
 ) Special Tools Required
Removal/Installation
18-2218-22 Front Suspension
Lower Ball Joint Replacement
(cont’d)
Lower Arm Removal/Installation
A
10x1.25mm
34 N·m
(3.5 kgf·m,
25 lbf·ft)
B C
D
7. Install the lower ball joint in the reverse order of removal, and note these items:
 First install all of the components, and lightly tighten the bolts and the nuts, then raise the
suspension to load it with the vehicle’s weight
before fully tightening to the specified torque
values.
 Be careful not to damage the ball joint boot when connecting the knuckle.
 Before connecting the lower ball joint to the knuckle, degrease the threaded section and the
tapered portion of the ball joint pin, the ball joint
connecting hole, the threaded section, and the
mating surfaces of the castle nut.
 Torque the castle nut to the lower torque specification, then tighten it only far enough to
align the slot with the ball joint pin hole. Do not
align the castle nut by loosening it.
 Use a new spindle nut during reassembly.
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
8. Check the wheel alignment, and adjust it if necessary (see page 18-5).  Bushing driver 07AAF-SVAA100
 Receiver set 07AAF-SVAA200
1. Raise the front of the vehicle, and support it with safety stands in the proper locations (see page
1-11).
2. Remove the front wheels.
3. Remove the flange nut (A) while holding the joint pin (B) with a hex wrench (C), then disconnect both
sides of the stabilizer link from the lower arm (D).
NOTE: Use the new flange nut during reassembly.
4. Turn the stabilizer bar backward to gain easier access to the front side of the lower arm mounting
bolt.
Replace.
08/08/21 14:57:35 61SNR030_180_0022
ProCarManuals.com
DYNOMITE -2009-


(#'
 ) Special Tools Required
Removal/Installation
18-2218-22 Front Suspension
Lower Ball Joint Replacement
(cont’d)
Lower Arm Removal/Installation
A
10x1.25mm
34 N·m
(3.5 kgf·m,
25 lbf·ft)
B C
D
7. Install the lower ball joint in the reverse order of removal, and note these items:
 First install all of the components, and lightly tighten the bolts and the nuts, then raise the
suspension to load it with the vehicle’s weight
before fully tightening to the specified torque
values.
 Be careful not to damage the ball joint boot when connecting the knuckle.
 Before connecting the lower ball joint to the knuckle, degrease the threaded section and the
tapered portion of the ball joint pin, the ball joint
connecting hole, the threaded section, and the
mating surfaces of the castle nut.
 Torque the castle nut to the lower torque specification, then tighten it only far enough to
align the slot with the ball joint pin hole. Do not
align the castle nut by loosening it.
 Use a new spindle nut during reassembly.
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
8. Check the wheel alignment, and adjust it if necessary (see page 18-5).  Bushing driver 07AAF-SVAA100
 Receiver set 07AAF-SVAA200
1. Raise the front of the vehicle, and support it with safety stands in the proper locations (see page
1-11).
2. Remove the front wheels.
3. Remove the flange nut (A) while holding the joint pin (B) with a hex wrench (C), then disconnect both
sides of the stabilizer link from the lower arm (D).
NOTE: Use the new flange nut during reassembly.
4. Turn the stabilizer bar backward to gain easier access to the front side of the lower arm mounting
bolt.
Replace.
08/08/21 14:57:35 61SNR030_180_0022
ProCarManuals.com
DYNOMITE -2009-



18-23
B
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
C
12x1.25mm
59N·m(6.0kgf·m,43lbf·ft) A
D
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft) E D
C
B
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
A
14x1.5mm
83 N·m
(8.5 kgf·m, 61 lbf·ft)
5. Remove the flange bolt and the self-locking nuts
from the lower arm (A).
NOTE: During installation, install the new flange
bolt and the new self-locking nuts. After lightly
tightening all three fasteners, tighten them to the
specified torque in the following order, the nut on
the front (B), the nut on the rear (C), then the bolt
(D).
6. Disconnect the lower ball joint (E) from the lower arm. 7. Remove the front side of the lower arm mounting
bolt (A).
NOTE: Use the new mounting bolt during
reassembly.
8. Remove the rear side of the lower arm mounting bolt (B), then remove the lower arm (C) from the
front suspension subframe (D).
NOTE: Use the new mounting bolt during
reassembly.
9. Install the lower arm in the reverse order of removal, and note these items:
 First install all of the components, and lightly tighten the bolts and the nuts, then raise the
suspension to load it with the vehicle’s weight
before fully tightening to the specified torque
values.
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
10. Check the wheel alignment, and adjust it if necessary (see page 18-5).
(cont’d)
Replace.
Replace.
Replace. Replace.
Replace.
08/08/21 14:57:36 61SNR030_180_0023
ProCarManuals.com
DYNOMITE -2009-