2006 ACURA CSX torque


(#'
 )
Î
(#'
 )
18-2518-25
Stabilizer Link Removal/Installation Stabilizer Bar Replacement
F
D E
B
10x1.25mm
34 N·m
(3.5 kgf·m,
25 lbf·ft)
C G
H
A
10x1.25mm
38 N·m
(3.9 kgf·m,
28 lbf·ft)
D
E
BC
FRONT
FRONT A
10x1.25mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
1. Raise the front of the vehicle, and support it withsafety stands in the proper locations (see page
1-11).
2. Remove the front wheel.
3. Remove the self-locking nut (A) and the flange nut (B) while holding the respective joint pin (C) with a
hex wrench (D), then remove the stabilizer link (E).
4. Install the stabilizer link on the stabilizer bar (F) and the lower arm (G) with the joint pins set at the
center of their range of the movement.
NOTE: The stabilizer link has a paint mark (H). Align
the paint mark on the stabilizer link facing rearward.
5. Install the new self-locking nut and the new flange nut, and tighten them to the specified torque values
while holding the respective joint pin with a hex
wrench.
6. Clean the mating surfaces of the brake disc and the inside of the wheel, then install the front wheel.
7. Test-drive the vehicle.
8. After 5 minutes of driving, torque the self-locking nut again to the specified torque value. 1. Raise the front of the vehicle, and support it with
safety stands in the proper locations (see page
1-11).
2. Remove the front wheels.
3. Disconnect both stab ilizer links from the stabilizer
bar (see page 18-25).
4. Remove the flange bolts (A) and the bushing holders (B), then remove the bushings (C) and the
stabilizer bar (D).
NOTE: During installation, align the paint marks (E)
on the stabilizer bar with the sides of the bushings.
5. Install the stabilizer bar in the reverse order of removal, and note these items:
 Note the right and left direction of the stabilizer bar.
 Note the direction of installation for the bushings and the bushing holders.
 Refer to stabilizer link removal/installation to connect the stab ilizer bar to the links (see page
18-25).
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
6. Check the wheel alignment, and adjust it if necessary (see page 18-5).
Replace.
Replace.
08/08/21 14:57:37 61SNR030_180_0025
ProCarManuals.com
DYNOMITE -2009-



Î



Installation
18-27
FRONT
A
B
C
A
’06-08 models except Type S model:
10x1.25mm
44N·m(4.5kgf·m,33lbf·ft)
’06-08 models type S model:
10x1.25mm
59N·m(6.0kgf·m,43lbf·ft)
’09 model:
10x1.25mm
59N·m(6.0kgf·m,43lbf·ft)
A
14x1.5mm
90 N·m
(9.2 kgf·m,
67 lbf·ft)
C
B
A
B
C
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)1. Install the damper/spring (A) onto the frame. Note
the direction of the damper mounting base as
shown.
NOTE: Be careful not to damage the body.
2. Loosely install the new flange nuts (A). NOTE: Install the service cap (B) and the lid (C) after
tightening the flange nuts to the specified torque
value. 3. Loosely install the new damper pinch bolts (A) and
the new self-locking nuts (B) to the damper (C).
4. Raise the front suspension with a floor jack to load the suspension with the vehicle’s weight.
5. Tighten the flange nuts on top of the damper to the specified torque value.
6. Tighten the damper pinch bolts to the specified torque value.
7. Install the wheel speed sensor harness clip (A) and the brake hose bracket (B) to the damper (C).
8. Install the service cap and the lid.
9. Clean the mating surfaces of the brake disc and the inside of the wheel, then install the front wheel.
10. Check the wheel alignment, and adjust it if necessary (see page 18-5).
11. Turn the ignition switch to ON (II), then turn the windshield wipers to the default positions, and turn
the ignition switch to LOCK (0).
Replace.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:57:39 61SNR030_180_0027
ProCarManuals.com
DYNOMITE -2009-

Ú


 Î

¶
Reassembly
18-30Front Suspension
Damper/Spring Disassembly, Inspection, and Reassembly (cont’d)
A
B
C
D
A B
C FRONT
FRONT
44 °24 ’ 3 °
A C
B
D
C
A
Left
Right
A
12 x 1.25 mm
44 N·m (4.5 kgf·m, 33 lbf·ft)
C
07AAA-SVAA100
B
1. Install the damper spring (A) on the upper springmounting cushion (B) by aligning the upper end (C)
of the damper spring with the ledge portion (D) of
the upper spring mounting cushion.
2. Compress the damper spring.
3. Install all the parts except the self-locking nut and the cap onto the damper unit (A) by referring to the
Exploded View.
4. Align the bottom of the spring (B) and the stepped part of the lower spring seat (C) on the damper unit. 5. Align the damper bracket (A) and the damper
mounting base (B) so that the ‘‘ ’’ stamp (C) points
toward the front.
6. Align the angle of the stud bolt (D) on the damper bracket as shown.
7. Install the new self-locking nut (A).
8. Hold the damper shaft using a hex wrench (B), and tighten the self-locking nut using the strut nut
adapter (C) and a torque wrench to the specified
torque value.
9. Remove the damper/spring from the strut spring compressor.
10. Install the cap.
Replace.
08/08/21 14:57:40 61SNR030_180_0030
ProCarManuals.com
DYNOMITE -2009-


18-34Rear Suspension
Knuckle/Hub Bearing Unit Replacement (cont’d)
D
14x1.5mm
88 N·m
(9.0 kgf·m,
65 lbf·ft)
A
B
C
Except Type S model:
12x1.25mm
69N·m(7.0kgf·m,51lbf·ft)
Type S model:
12x1.25mm
74 N·m (7.5 kgf·m, 54 lbf·ft)
8. Mark the cam positions of the adjusting bolt (A) and the adjusting cam plate (B) with the frame, then
remove the self-locking nut (C), the adjusting cam
plate, and the adjusting bolt. Discard the self-
locking nut.
NOTE: Use a new adjusting bolt and a new self-
locking nut during reassembly.
9. Remove the flange bolt (D), and remove the knuckle.
NOTE: Use the new flange bolt during reassembly. 10. Install the knuckle in the reverse order of removal,
and note these items:
 First install all of the components, and lightly tighten the bolts and the nuts, then raise the
suspension to load it with the vehicle’s weight
before fully tightening to the specified torque
values.
 Align the cam positions of the adjusting bolt and the adjusting cam plate with the marked
positions when tightening the self-locking nut.
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
11. Check the wheel alignment, and adjust it if necessary (see page 18-5).
Replace.
Replace.
Replace.
08/08/21 14:57:43 61SNR030_180_0034
ProCarManuals.com
DYNOMITE -2009-




(#'

 )
18-35
Upper Arm Removal/Installation
A A
B A
12x1.25mm
59 N·m
(6.0 kgf·m, 43 lbf·ft)
B
12x1.25mm
108 N·m
(11.0 kgf·m,
79.6 lbf·ft)
C
NOTE: There are two types of rear upper arms. Those
that are marked with ‘‘C’’ (A), and those with no marks.
Be sure to use the correct alignment specifications.
1. Raise the rear of the vehicle, and support it with safety stands in the proper locations (see page
1-11).
2. Remove the rear wheel.
3. Position a floor jack at the connecting point of the trailing arm (A) and the knuckle (B). Raise the floor
jack until the suspension begins to compress. 4. Remove the flange bolts (A) from the vehicle.
NOTE: Use new flange bolts during reassembly.
5. Remove the flange bolt (B) from the knuckle, and remove the upper arm (C).
NOTE: Use the new flange bolt during reassembly.
6. Install the upper arm in the reverse order of removal, and note these items:
 First install all of the components, and lightly tighten the bolts, then raise the suspension to
load it with the vehicle’s weight before fully
tightening to the specified torque values.
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
7. Check the wheel alignment, and adjust it if necessary (see page 18-5).
Replace. Replace.
08/08/21 14:57:43 61SNR030_180_0035
ProCarManuals.com
DYNOMITE -2009-


(#'

 )
18-3718-37
Stabilizer Link Removal/Installation
A
Except Type S model:
10x1.25mm
39 N·m
(4.0 kgf·m, 29 lbf·ft) C
D E
F
GH
B
10x1.25mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
Type S model:
10x1.25mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
11. Install the trailing arm in the reverse order of
removal, and note these items:
 First install all of the components, and lightly tighten the bolts, then raise the suspension to
load it with the vehicle’s weight before fully
tightening to the specified torque values.
 Check the brake hose for interference and twisting.
 Before installing the wheel, clean the mating surfaces on the brake disc and the inside of the
wheel.
12. Check the wheel alignment, and adjust it if necessary (see page 18-5). 1. Raise the rear of the vehicle, and support it with
safety stands in the proper locations (see page
1-11).
2. Remove the rear wheel.
3. Remove the self-locking nut (A) and the flange nut (B) while holding the respective joint pin (C) with a
hex wrench (D), then remove the stabilizer link (E).
4. Install the stabilizer link on the stabilizer bar (F) and trailing arm (G) with the joint pins set at the center
of their range of the movement.
NOTE: The stabilizer link has a paint mark (H). Align
the paint mark on the stabilizer link facing rearward.
5. Install the new self-locking nut and the new flange nut, and tighten them to the specified torque values
while holding the respective joint pin with a hex
wrench.
6. Clean the mating surfaces of the brake disc and the inside of the wheel, then install the rear wheel.
7. Test-drive the vehicle.
8. After 5 minutes of driving, torque the self-locking nut again to the specified torque values.
Replace.
Replace.
Replace.
08/08/21 14:57:44 61SNR030_180_0037
ProCarManuals.com
DYNOMITE -2009-


(#'

 )
18-3718-37
Stabilizer Link Removal/Installation
A
Except Type S model:
10x1.25mm
39 N·m
(4.0 kgf·m, 29 lbf·ft) C
D E
F
GH
B
10x1.25mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
Type S model:
10x1.25mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
11. Install the trailing arm in the reverse order of
removal, and note these items:
 First install all of the components, and lightly tighten the bolts, then raise the suspension to
load it with the vehicle’s weight before fully
tightening to the specified torque values.
 Check the brake hose for interference and twisting.
 Before installing the wheel, clean the mating surfaces on the brake disc and the inside of the
wheel.
12. Check the wheel alignment, and adjust it if necessary (see page 18-5). 1. Raise the rear of the vehicle, and support it with
safety stands in the proper locations (see page
1-11).
2. Remove the rear wheel.
3. Remove the self-locking nut (A) and the flange nut (B) while holding the respective joint pin (C) with a
hex wrench (D), then remove the stabilizer link (E).
4. Install the stabilizer link on the stabilizer bar (F) and trailing arm (G) with the joint pins set at the center
of their range of the movement.
NOTE: The stabilizer link has a paint mark (H). Align
the paint mark on the stabilizer link facing rearward.
5. Install the new self-locking nut and the new flange nut, and tighten them to the specified torque values
while holding the respective joint pin with a hex
wrench.
6. Clean the mating surfaces of the brake disc and the inside of the wheel, then install the rear wheel.
7. Test-drive the vehicle.
8. After 5 minutes of driving, torque the self-locking nut again to the specified torque values.
Replace.
Replace.
Replace.
08/08/21 14:57:44 61SNR030_180_0037
ProCarManuals.com
DYNOMITE -2009-



InspectionInstallation
18-41
A
B
A
Except Type S model:
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
Type S model:
12x1.25mm
69 N·m (7.0 kgf·m, 51 lbf·ft)
1. Push on the damper as shown.
2. Compress the damper assembly by hand, and check for smooth operation through a full stroke,
both compression and extension. The damper
should extend smoothly and constantly when
compression is released. If it does not, the gas is
leaking and the damper should be replaced.
3. Check for oil leaks, abnormal noises, or binding during these tests. 1. Install the damper mounting bushing (A) onto the
damper unit. Position the damper assembly (B)
between the body and tra iling arm.
NOTE: Be careful not to damage the body.
2. Position a floor jack under the tra iling arm to
support the suspension, then install the new
damper mounting bolt (A).
3. Loosely tighten the damper mounting bolt.
4. Raise the rear suspension with the jack until the vehicle just lifts off the safety stands, then tighten
the damper mounting bolt to the specified torque
value.
(cont’d)
Replace.
Replace.
08/08/21 14:58:17 61SNR030_180_0041
ProCarManuals.com
DYNOMITE -2009-