2006 ACURA CSX torque


(#'
 ) 
(#'

 )
Upper Dashboard Support Gusset Torque Rear Floor Upper Cross-member Gusset Torque
Driver’s side
Passenger’s side
20-18620-186Frame
Upper Dashboard Support Gusset
Replacement
Rear Floor Upper Cross-member
Gusset Replacement
8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft)6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) UPPER DASHBOARD
SUPPORT GUSSET
SUPPORT
BRACKET
(MT model)
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft) UPPER DASHBOARD
SUPPORT GUSSET
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft) 8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
REAR FLOOR UPPER
CROSS-MEMBER GUSSET
NOTE: Take care not to scratch the body. NOTE: Take care not to scratch the body.
08/08/21 15:05:36 61SNR030_200_0188
ProCarManuals.com
DYNOMITE -2009-


(#'
 )
Front Subframe Torque
20-187
Subframe Replacement
10x1.25mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
REFERENCE HOLE
(Body side)
Reference hole alignment
SUBFRAME
SCREWDRIVER or
TAPERED PUNCH
INSTALLATION
REFERENCE HOLE FRONT SUSPENSION
SUBFRAME INSTALLATION
REFERENCE HOLE
(Subframe side)
To body To body
To body
GEARBOX REAR
STIFFENER
GEARBOX FRONT
STIFFENER
BODY MOUNT
BRACKET
SPECIAL BOLTS
14 x 1.5 mm
103 N·m
(10.5 kgf·m, 75.9 lbf·ft) 12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
FRONT SUSPENSION
SUBFRAME
To body
INSTALLATION
REFERENCE HOLE
NOTE:  After loosening the subframe mounting bolts, be sure to replace them with new ones.
 When installing, align both installation reference holes in the subframe with both reference holes in the body using a screwdriver or tapered punch as a guide.
Replace.
08/08/21 15:05:36 61SNR030_200_0189
ProCarManuals.com
DYNOMITE -2009-

Î(#'
!)
Top View
20-188Frame
Frame Repair Chart
453 (17.8)
659 (25.9)
1253 (49.33)
1147 (45.16)
1119 (44.06)
1070 (42.13)
521 (20.5) 494 (19.4)
980 (38.6)
478 (18.82) 479 (18.86)
470 (18.5)
852 (33.5)
654 (25.7)
940 (37.0)
1010 (39.76) 482 (18.98)
88 (3.5)
28 (1.1)
129 (5.08)
139 (5.5)
447 (17.6) 53 (7.4)
67 (2.6)
88 (3.5)
310 (12.2) 425 (16.7) 675 (26.6)
1440 (56.70)
2170 (85.43)2216 (87.24)
2282 (89.84)2348 (92.44)2602 (102.4)
2653 (104.4)2704 (106.5)
2794 (110.0)2814 (110.8)2824 (111.2) 2850 (112.2)
2964 (116.7) 3165 (124.6)
166
(6.54)
212 (8.45)
320 (12.6) d3
d2
d1
198 (7.80)
88 (3.46)
92 (3.62)
97 (3.8)
For front subframe mount ø16 (0.63) forward
a
b1
b2
b3
c1
c2
c3
d1
d2
d3
e1
e2
e3
e4
f
g
h
i For engine side mount ø15 (0.59)
For engine side mount ø15 (0.59)
For engine side mount ø12 (0.47)
For transmission mount ø15 (0.59)
For transmission mount ø11 (0.43)
For transmission mount ø15 (0.59)
For torque rod mount upper ø14.5 (0.57) x 19.5 (0.77) slot
Torque rod center point
For torque rod mount lower ø14 (0.55) x 22 (0.87) slot For front damper mount ø11.5 (0.45)
For front damper mount ø11.5 (0.45)
For front damper mount ø11.5 (0.45) Frontdampercenterø74(2.9)
For front subframe mount ø13 (0.51) middle
For front subframe mount ø16 (0.63) rearward
Outrigger locating hole ø25 (0.98)
Front floor locating hole ø50 (1.97)
c4 For transmission mount ø15 (0.59) MT only POINT a
POINT b1
POINT b2POINT b3
POINT c4POINT c2 POINT c3
POINT d1
POINT d2 POINT d3
POINT e1
POINT e2 POINT e3POINT e4
POINT f POINT g
POINT h POINT i
POINT c1119 (4.69)
VERTICAL LINE
CENTER LINE
Unit: mm (in.)
ø: Inner diameter
08/08/21 15:05:37 61SNR030_200_0190
ProCarManuals.com
DYNOMITE -2009-


¦§
µ
Side View
20-190Frame
Frame Repair Chart (cont’d)
242 (9.53)
617 (24.3)
515 (20.3)
427 (16.8)
309 (12.2)
307 (12.1)
306 (12.0) 301 (11.9)
49 (1.9)
135 (5.31) 44 (1.73)
40 (1.57)
607 (23.9)
615 (24.2)
620 (24.4)
556 (21.9)
526 (20.7)
495 (19.5)
M14x1.5
M12x1.25M12x1.25M10x1.25
M12x1.25 M12x1.25M14x1.5
M10x1.25
M12x1.25 ø74 (2.9)
4.1 °
10 ° 110 °
120 °
3ø11.5(0.45) ø110 (43.3)
7.3 ° M12x1.25
For front subframe mount ø16 (0.63) forward
a
b1
b2
b3
c1
c2
c3
d1
d2
d3
e1
e2
e3
e4
f
g
h
i For engine side mount ø15 (0.59)
For engine side mount ø15 (0.59)
For engine side mount ø12 (0.47)
For transmission mount ø15 (0.59)
For transmission mount ø11 (0.43)
For transmission mount ø15 (0.59)
For torque rod mount upper
ø14.5 (0.57) x 19.5 (0.77) slot
Torque rod center point
For torque rod mount lower
ø14 (0.55) x 22 (0.87) slot
For front damper mount ø11.5 (0.45)
For front damper mount ø11.5 (0.45)
For front damper mount ø11.5 (0.45) Front damper center ø74 (2.9)
For front subframe mount ø13 (0.51) middle
For front subframe mount ø16 (0.63) rearward
Outrigger locating hole ø25 (0.98)
Front floor locating hole ø50 (1.97)
c4 For transmission mount ø15 (0.59) MT only
POINT a
POINT b1
POINT b2 POINT b3
POINT c1POINT c2 POINT c3
POINT d1
POINT d2
POINT d3 POINT e1
POINT e2
POINT e3POINT e4
POINT f POINT gPOINT h
POINT i
POINT e1
POINT e2
POINT e3
POINT e4
POINT e3
AA SECTION: AA
POINT c4
VERTICAL LINE
BASE
LINE
Unit: mm (in.)
ø: Inner diameter
08/08/21 15:05:39 61SNR030_200_0192
ProCarManuals.com
DYNOMITE -2009-

µ
(#'
)
GroundComponent or Circuit Grounded
22-64Ground Distribution
Ground to Components Index
G1 Battery
G2 Engine
G3 Transmission housing
G101 A/T clutch pressure control solenoid valves A, B, C (A/T), CKP sensor, CMP sensor A, CMP sensor B, Data link connector (DLC), ECM/PCM (LG1), ECM/PCM (LG2), ECM/PCM (PG1), ECM/PCM (PG2), ECM/PCM (PGMETCS), EGR valve (K20Z2 engine), Ignition
coils, Immobilizer-keyless control unit, Rocker arm oil control solenoid, Rocker arm oil pressure switch, Transmission range
switch (A/T), VTC oil control solenoid valve
Shielding between the ECM/PCM and Knock sensor (KS) has wire.
Shielding between the ECM/PCM and Secondary HO2S (Sensor 2) has wire.
G201 Right fog light , Right front parking light, Right front side marker light, Right front turn signal light, Right headlight (high/low beams), Right HID unit , Windshield washer motor, Windshield wiper motor
G202 ABS modulator-control unit , VSA modulator-control unit
G301 A/C condenser fan motor, Blower motor relay, ELD, Left fog light , Left front parking light, Left front side marker light, Left front turn signal light, Left headlight (high/low beams), Left HID unit , Radiator fan motor (via fan control relay)
G401 Brake fluid level switch, Clutch interlock switch (M/T), Clutch pedal position switch (M/T), Hood switch, MICU (PG), Power transistor, Washer fluid level switch (G401 connects to G601 via under-dash fuse/relay box)
G402 EPS control unit
G403 Torque sensor
G501 Dash lights brightness controller and odometer select/reset switch, Driver’s door key cylinder switch, Driver’s door lock knob switch, HandsFreeLink control unit , MICU (SG), VSA OFF switch
G502 Data link connector (DLC), Front accessory power socket, Glove box light, Right power mirror defogger, Right side turn signal light
G503 Accessory power socket relays (front and console), Driver’s door lock switch, Gauge control module (tach), Left power mirror defogger, Left side turn signal light, Moonroof control unit/motor, Power mirror switch light, Power mirror switch, Power
window master switch (main switch), Power window master switch, Vanity mirror lights (driver’s and front passenger’s)
G504 Cable reel (steering wheel switches ground), Climate control unit, Front passenger’s door lock knob switch, Front passenger’s door lock switch, Gauge control module (speedo), Gauge control module (tach), Ignition key switch, Navigation unit , TPMS
control unit
G505 Audio unit , Navigation unit
G506 Memory erase signal (MES) connector, SRS unit (2 wires)
G601 A/T gear position console panel light/Park-pin switch (A/T), Console accessory power socket , Fuel pump, MICU (PG), Seat heater relays (driver’s and front passenger’s), Seat heater switches (driver’s and front passenger’s), Seat heaters (driver’s and
front passenger’s), Stereo amplifier (G601 connects to G401 via under-dash fuse/relay box)
Shielding between the left side impact sensor (FIRST) and rear safing sensor has wire.
Shielding between the SRS unit and left side impact sensor (FIRST) has wire.
G602 Driver’s seat belt buckle switch, Front passenger’s seat belt buckle switch, Left rear door lock knob switch, MICU (SG), MICU service check connector, ODS unit, Right rear door lock knob switch, Yaw rate-lateral acceleration sensor
Shielding between the right side impact sensor (FIRST) and right side impact sensor (SECOND) have wires.
Shielding between the SRS unit and right side impact sensor (FIRST) has wire.
G603 Noise condenser Shielding between the rear safing sensor and left side impact sensor (SECOND) has wire.
G701 High mount brake light, Left back-up light, Left inner taillight, Left rear side marker light, Left rear turn signal light, Left taillight/ brake light, License plate lights, Right back-up light, Right inner taillight, Right rear side marker light, Right rear turn signal light,
Right taillight/brake light, Trunk lid release actuator/Trunk lid latch switch
G801 Rear window defogger ( )
1: ’06-07 Touring and Premium models
2: ’07 TYPE S and ’08-09 models
3: ’08-09 models
4: TYPE S and ’08 premium and ’09 models
5: With HID
6: Without navigation system
7: With navigation system
8: ’09 model with navigation system
9: ’06-08 models, and ’09 model without navigation system
10: TYPE S model
4
512 4
5
82 3
7
3
67
9
10
2
08/08/21 14:24:03 61SNR030_220_0066
ProCarManuals.com
DYNOMITE -2009-


Upper anchor bolt installation
24-5
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A
UPPER ANCHOR
UPPER ANCHOR
BOLT
TOOTHED
LOCK WASHER
BUSHING
THREAD LOCK COLLAR
9. Remove the shoulder anchor adjuster (A).
10. Install the seat belt in the reverse order of removal, and note these items:
 Apply medium strength liquid thread lock to the anchor bolts before reinstallation.
 Tighten the bolts by hand first, then tighten to the specification with a torque wrench.
 Check that the retractor locking mechanism functions as described (see page 24-9).
 Assemble the washer, collar, and bushing on the upper anchor bolt as shown.
 If the seat belt tensioner has been deployed, replace the front seat belt protector with a new
one.
 Before installing the anchor bolts, make sure there are no twists or kinks in the seat belt.
 Make sure the seat belt tensioner connector is properly plugged in.
 Check for any DTCs that may have been set during repairs, and clear them using the HDS.
 Do the battery terminal reconnection procedure (see page 22-68).
(cont’d)
08/08/21 13:54:08 61SNR030_240_0005
ProCarManuals.com
DYNOMITE -2009-



(#' )
Center anchor bolt installation
Rear Seat Belt
24-724-7
Rear Seat Belt Replacement
CENTER ANCHOR
CENTER ANCHOR
BOLT
TOOTHED
LOCK WASHER SPRING WASHER
A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
6. Install the buckle in the reverse order of removal,
and note these items:
 Assemble the washers on the center anchor bolt as shown.
 Apply medium strength liquid thread lock to the center anchor bolt before reinstallation.
 Tighten the bolts by hand first, then tighten to specification with a torque wrench.
 Make sure the seat belt switch connector and seat belt buckle tensioner connector are plugged
in properly.
 Check for any DTCs that may have been set during repairs, and clear them using the HDS.
 Do the battery terminal reconnection procedure (see page 22-68). NOTE: Check the second row seat belts for damage,
and replace them if necessary.
1. Remove the rear seat cushion (see page 20-133).
2. Remove the lower anchor bolt (A).
3. Remove these items:  Rear seat side bolsters, both sides (see page20-134)
 C-pillar trim, both sides (see page 20-75)
 Rear shelf (see page 20-78)
(cont’d)
08/08/21 13:54:09 61SNR030_240_0007
ProCarManuals.com
DYNOMITE -2009-



(#' )
Center anchor bolt installation
Rear Seat Belt
24-724-7
Rear Seat Belt Replacement
CENTER ANCHOR
CENTER ANCHOR
BOLT
TOOTHED
LOCK WASHER SPRING WASHER
A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
6. Install the buckle in the reverse order of removal,
and note these items:
 Assemble the washers on the center anchor bolt as shown.
 Apply medium strength liquid thread lock to the center anchor bolt before reinstallation.
 Tighten the bolts by hand first, then tighten to specification with a torque wrench.
 Make sure the seat belt switch connector and seat belt buckle tensioner connector are plugged
in properly.
 Check for any DTCs that may have been set during repairs, and clear them using the HDS.
 Do the battery terminal reconnection procedure (see page 22-68). NOTE: Check the second row seat belts for damage,
and replace them if necessary.
1. Remove the rear seat cushion (see page 20-133).
2. Remove the lower anchor bolt (A).
3. Remove these items:  Rear seat side bolsters, both sides (see page20-134)
 C-pillar trim, both sides (see page 20-75)
 Rear shelf (see page 20-78)
(cont’d)
08/08/21 13:54:09 61SNR030_240_0007
ProCarManuals.com
DYNOMITE -2009-