2005 TOYOTA AVENSIS transmission

C94578
N´m (kgf´cm, ft´lbf) : Specified torque
Apply MP greaseSelecting Bellcrank Support
Selecting Bellcrank
Dust Cover No.2Selecting Bellcrank
No.2 Bush
Selecting Bellcrank No.2
Selecting Bellcrank
No.2 Bush
Selecting Bellcrank
No.2 Plate Washer
Selecting Bellcrank
Dust Cover No.1
Shift & Select
Lever Bush
12 (120, 9)
± MANUAL TRANSMISSION/TRANSAXLESHIFT & SELECT LEVER SHAFT ASSY (C250)
41±59
C250 M/T REPAIR MANUAL (RM1020E)

4002J±01
D03796
SST
C67862
C67865
C67863
40±56
± AUTOMATIC TRANSMISSION / TRANSSECOND BRAKE PISTON ASSY (U34#E Series)
U340E A/T REPAIR MANUAL (RM824E)
SECOND BRAKE PISTON ASSY (U34#E Series)
OVERHAUL
1. REMOVE 2ND BRAKE PISTON RETURN SPRING
SUB±ASSY
[ 35608L / 3509 ]
(a) Place SST on the piston return spring and compress.
SST 09387±00060
(b) Using a screwdriver, remove the snap ring.
(c) Remove the 2nd brake return spring from the 2nd brake
cylinder.
2. INSPECT 2ND BRAKE PISTON RETURN SPRING
SUB±ASSY
[ 35608L / 3509 ]
(a) Using vernier calipers, measure the free length of the
spring together with the spring seat.
Standard free length: 14.65 mm (0.5768 in.)
3. REMOVE 2ND BRAKE PISTON
[ 35624E / 3509 ]
(a) Hold the 2nd brake piston and apply compressed air (392
kPa, 4.0 kgf
cm
2, 57 psi) to the 2nd brake cylinder to re-
move the 2nd brake piston.

C67864
C67864
C67866
C67862
D03796
SST
± AUTOMATIC TRANSMISSION / TRANSSECOND BRAKE PISTON ASSY (U34#E Series)
40±57
U340E A/T REPAIR MANUAL (RM824E)
4. REMOVE 2ND BRAKE CYLINDER O±RING
[ 35664D / 3509 ]
(a) Using a screwdriver, remove the 2 O±rings from the 2nd
brake cylinder.
5. INSTALL 2ND BRAKE CYLINDER O±RING
[ 35664D / 3509 ]
(a) Install 2 new O±ring to the 2nd brake cylinder.
NOTICE:
Be careful not to damage the O±ring.
6. INSTALL 2ND BRAKE PISTON
[ 35624E / 3509 ]
(a) Coat 2 new O±rings with ATF and install them in the 2nd
brake cylinder.
(b) Be careful not to damage the O±rings and press in the
2nd brake piston into the 2nd brake cylinder with a your
hands.
7. INSTALL 2ND BRAKE PISTON RETURN SPRING
SUB±ASSY
[ 35608L / 3509 ]
(a) Install the piston return spring.
(b) Place SST on the piston return spring, and compress the
piston return spring with a press.
SST 09387±00060
(c) Using a screwdriver, install the snap ring.
NOTICE:
Be sure the end gap of the snap ring is not aligned with the
piston return spring claw.

9808L±01
± COMPONENTS151350
98±3
3503/TRANSMISSION CASE & OIL PAN (ATM)
(0008± )NZE121..ATM U340E

9808J±01
± COMPONENTS151350
98±1
3501/TRANSAXLE OR TRANSMISSION ASSY & GASKET KIT (ATM)
(0008± )NZE121..ATM U340E

4002N±01
D25171
D25172
D25173
C81314
± AUTOMATIC TRANSMISSION / TRANSFRONNT DIFFERENTIAL ASSY (U34#E Series)
40±71
U340E A/T REPAIR MANUAL (RM824E)
FRONNT DIFFERENTIAL ASSY (U34#E Series)
OVERHAUL
1. REMOVE SPEEDOMETER DRIVE (ATM) GEAR
[ 33481X / 4301 ]
(a) Remove the speedometer drive gear from the differential
case.
2. REMOVE FRONT DIFFERENTIAL RING GEAR
[ 41221 / 4301 ]
(a) Put match±marks on the front differential ring gear and
differential case.
(b) Using SST and a hammer, unstake the lock plate.
SST 09930±00010
(c) Remove the 8 bolts and lock plate.

C81315
C81316
C81317
C81318
C81319
40±72
± AUTOMATIC TRANSMISSION / TRANSFRONNT DIFFERENTIAL ASSY (U34#E Series)
U340E A/T REPAIR MANUAL (RM824E)
(d) Using a plastic hammer, remove the front differential ring
gear from the differential case.
3. REMOVE FRONT DIFFERENTIAL PINION SHAFT
STRAIGHT PIN
[ 41342A / 4301 ]
(a) Using a punch and a hammer, unstake the differential
case.
(b) Using a pin punch and a hammer, remove the straight pin.
4. REMOVE FRONT DIFFERENTIAL PINION SHAFT
NO.1
[ 41342F / 4301 ]
(a) Remove the pinion shaft from the front differential case.
5. REMOVE FRONT DIFFERENTIAL SIDE GEAR
[ 41331F / 4301 ]
(a) Remove the 2 pinions, 2 thrust washers, 2 side gears and
2 thrust washers No.1 from the front differential case.

C68188
D25174
SST
D25175
SST
D25176
SST
± AUTOMATIC TRANSMISSION / TRANSFRONNT DIFFERENTIAL ASSY (U34#E Series)
40±73
U340E A/T REPAIR MANUAL (RM824E)
6. REMOVE DIFFERENTIAL DRIVE PINION PLUG
[ 41211E / 4301 ]
(a) Using a brass bar and a hammer, remove the differential
drive pinion plug.
7. REMOVE COUNTER DRIVEN GEAR
[ 35783R / 4301 ]
(a) Using SST and a press, remove the counter driven gear
from the differential drive pinion.
SST 09950±60010 (09951±00350), 09950±70010
(09951±07150)
8. INSTALL COUNTER DRIVEN GEAR
[ 35783R / 4301 ]
(a) Using SST and a press, install the counter driven gear to
the differential drive pinion.
SST 09950±60010 (09951±00350), 09950±70010
(09951±07150)
NOTICE:
When replacing the counter driven gear, replace the count-
er drive gear in the transaxle case, too.
HINT:
The differential drive pinion shall be press±fit until it comes to
contact with the counter driven gear.
9. INSTALL DIFFERENTIAL DRIVE PINION PLUG
[ 41211E / 4301 ]
(a) Using SST and a plastic hammer, install a new differential
drive pinion plug to the differential drive pinion
SST 09221±25026 (09221±00071)
Standard clearance:
2.5 ± 2.6 mm (0.0984 ± 0.1023 in.)