2005 TOYOTA AVENSIS brake

D25466
12
12
(+)
(±)
05±954± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))
AVENSIS REPAIR MANUAL (RM1018E)
DTC P0746 PRESSURE CONTROL SOLENOID ºAº
PERFORMANCE (SHIFT SOLENOID VALVE
SL1)
SYSTEM DESCRIPTION
The ECM uses signals from the vehicle speed sensor to detect the actual gear position (1st, 2nd, 3rd or O/D
gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
troubles of the shift solenoid valves and valve body.
DTC No.DTC Detecting ConditionTrouble Area
P0746The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Shift solenoid valve SL1 is stuck open or closed

Valve body is blocked up or stuck

Automatic transaxle (clutch, brake or gear etc.)
INSPECTION PROCEDURE
1 INSPECT SHIFT SOLENOID VALVE(SL1)
(a) Remove the shift solenoid valve SL1.
(b) Measure the resistance between terminals of the shift so-
lenoid valve SL1.
OK:
Resistance: 5.0 to 5.6
at 20C (68F)
(c) Connect the positive (+) lead with a 21 W bulb to terminal
2 and the negative (±) lead to terminal 1 of the solenoid
valve connector, then check the movement of the sole-
noid valve.
OK:
The solenoid valve makes an operating noise.
NG REPLACE SHIFT SOLENOID VALVE(SL1)
OK
2 INSPECT TRANSMISSION VALVE BODY ASSY
NG REPAIR OR REPLACE TRANSMISSION VALVE
BODY ASSY
OK
05C9D±01

±
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT](U241E(1AZ±FSE))05±947
AVENSIS REPAIR MANUAL (RM1018E)
DTCP0724BRAKE SWITCH ºBº CIRCUIT HIGH
CIRCUIT DESCRIPTION
The purpose of this circuit is to prevent the engine from stalling while dr\
iving in lock±up condition, when
brakes are suddenly applied.
When the brake pedal is depressed, this switch sends signals to the ECM. Then\
the ECM cancels the opera-
tion of the lock±up clutch while braking is in progress.
DTC No.DTC Detecting ConditionTrouble Area
P0724The stop light switch does not turn off even once the vehicle is
driven (2±trip detection logic).
Short in stop light switch signal circuit

Stop light switch

ECM
WIRING DIAGRAM
See page 05±475.
INSPECTION PROCEDURE
1 INSPECT STOP LAMP SWITCH ASSY
NG REPLACE STOP LAMP SWITCH ASSY
OK
2 CHECK HARNESS AND CONNECTOR(STOP LAMP SWITCH ASSY ± ECM)
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPAIR OR REPLACE ECM
05C9A±01

±
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))05±937
AVENSIS REPAIR MANUAL (RM1018E)
Chapter 3: Off±vehicle Repair
(
: U241E AUTOMATIC TRANSAXLE Repair Manual Pub. No. RM840U)
SymptomSuspect AreaSee page
Vehicle does not move in any forward range or reverse range
1. Front and rear planetary gear
2. U/D planetary gear
3. U/D one±way clutch (F
2)
4. Forward clutch (C
1)
5. U/D brake (B
3)










Vehicle does not move in R range
1. Front and rear planetary gear unit
2. U/D planetary gear
3. Direct clutch (C
2)
4. U/D brake (C
3)
5. 1st and reverse brake (B
2)










No up±shift (1st
2nd)1. No.1 one±way clutch (F1)
2. 2nd brake (B
1)




No up±shift (2nd
3rd)Direct clutch (C2)

No up±shift (3rd
O/D)U/D clutch (C3)

No lock±up or No lock±up offTorque converter clutch40±37
Harsh engagement (N
D)
1. Forward clutch (C1)
2. U/D one±way clutch (F
2)
3. No.1 one±way clutch (F
1)






Harsh engagement (N
R)1. Direct clutch (C2)
2. 1st and reverse brake (B
2)




Harsh engagement (Lock±up)Torque converter clutch40±37
Slip or shudder (Forward position: After warm±up)
1. Torque converter clutch
2. Forward clutch (C
1)
3. Direct clutch (C
2)
4. U/D brake (C
3)
5. No.1 one±way clutch (F
1)
6. U/D one±way clutch (F
2)
40±37









Slip or shudder (R range)1. Direct clutch (C2)
2. 1st and reverse brake (B
2)




Slip or shudder (1st)No.1 one±way clutch (F1)

Slip or shudder (2nd)1. U/D one±way clutch (F2)
2. 2nd brake (B
1)




Slip or shudder (3rd)Direct clutch (C2)

Slip or shudder (O/D)U/D clutch (C3)

No engine braking (1st ± 3rd: D range)U/D brake (B3)

No engine braking (1st: L range)1st and reverse brake (B2)

No engine braking (2nd: 2 range)2nd brake (B1)

Poor acceleration (All range)1. Torque converter clutch
2. U/D planetary gear40±37

Poor acceleration (O/D)1. U/D clutch (C3)
2. U/D planetary gear



Large shift shock or engine stalls when starting off or stoppingTorque converter clutch40±37

0567Q±09
±
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT](U241E(1AZ±FSE))05±931
AVENSIS REPAIR MANUAL (RM1018E)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the circuit listed in th\
e table below and proceed to the
page given.
*
1 : ± ... MIL does not light /
... MIL light up
DTC No.
(See Page)Detection ItemTrouble AreaMIL *Memory
P0500
(05±453 )Vehicle Speed Sensor ºAº
 Combination meter
 Open or short in vehicle speed sensor circuit
 Vehicle speed sensor
 ECM


P0705
(05±938)Transmission Range Sensor Cir-
cuit Malfunction (PRNDL Input) Short in park/neutral position switch circuit
 Park/neutral position switch
 ECM


P0710
(05±941)Transmission Fluid Temperature
Sensor ºAº Circuit

P0711
(05±943)Transmission Fluid Temperature
Sensor ºAº Performance Open or short in ATF temperature sensor circuit
AT F t t


P0712
(05±941)Transmission Fluid Temperature
Sensor ºAº Circuit Low Input ATF temperature sensor
 ECM


P0713
(05±941)Transmission Fluid Temperature
Sensor ºAº Circuit High Input

P0717
(05±945)Turbine Speed Sensor Circuit No
Signal
 Open or short in speed sensor (NT) circuit
 Speed sensor (NT)
 ECM
 Automatic transaxle assembly


P0724
(05±947)Brake Switch ºBº Circuit High
 Short in stop light switch circuit
 Stop light switch
 ECM


P0741
(05±948)Torque Converter Clutch Sole-
noid Perfomance
(Shift Solenoid Valve DSL) Shift solenoid valve DSL is stuck open or closed
 Valve body is blocked up or stuck
 Shift solenoid valve DSL
 ECM


P0743
(05±951)Torque Converter Clutch Circuit
Electrical
(Shift Solenoid Valve DSL) Open or short in shift solenoid valve DSL circuit
 Shift solenoid valve DSL
 ECM


P0746
(05±954)Pressure Control Solenoid ºAº
Performance
(Shift Solenoid Valve SL1) Shift solenoid valve SL1 is stuck open or closed
 Valve body is blocked up or stuck
 Shift solenoid valve SL1
 ECM


P0748
(05±956)Pressure Control Solenoid ºAº
Electrical
(Shift Solenoid Valve SL1) Open or short in shift solenoid valve SL1 circuit
 Shift solenoid valve SL1
 ECM


P0766
(05±962)Shift Solenoid ºDº Performance
(Shift Solenoid Valve S4)
 Shift solenoid valve S4 is stuck open or closed
 Valve body is blocked up or stuck
 Shift solenoid valve S4
 ECM


P0776
(05±963)Pressure Control Solenoid ºBº
Performance
(Shift Solenoid Valve SL2) Shift solenoid valve SL2 is stuck open or closed
 Valve body is blocked up or stuck
 Shift solenoid valve SL2
 ECM



0567Q±07
05±996±
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT](U341E)
AVENSIS REPAIR MANUAL (RM1018E)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the circuit listed in th\
e table below and proceed to the
page given.
*
1 :
... MIL light up
DTC No.
(See Page)Detection ItemTrouble AreaMIL *1Memory
P0500
(05±98)Vehicle Speed Sensor Malfunc-
tion
 Combination meter
 Open or short in speed sensor circuit
 Speed sensor
 ECM


P0710
(05±1003)Transmission Fluid Temperature
Sensor Circuit Malfunction
(ATF Temperature Sensor)
 Open or short in ATF temp. sensor circuit


P0711
(05±1005)
Transmission Fluid Temperature
Sensor Circuit Range/Perfor-
mance
(ATF Temperature Sensor)
Oen or short in AT F tem. sensor circuit
 Transmission wire (ATF temperature sensor)
 ECM


P0750
(05±1007)Shift Solenoid ºAº Malfunction
(Shift Solenoid Valve S1) Shift solenoid valve S1 is stuck open or closed
 Valve body is blocked up or stuck
 Automatic transaxle (clutch, brake or gear etc.)


P0753
(05±1010)Shift Solenoid ºAº Electrical
(Shift Solenoid Valve S1) Open or short in shift solenoid valve S1 circuit
 Shift solenoid valve S1
 ECM


P0755
(05±1007)Shift Solenoid ºBº Malfunction
(Shift Solenoid Valve S2) Shift solenoid valve S2 is stuck open or closed
 Valve body is blocked up or stuck
 Automatic transaxle (clutch, brake or gear etc.)


P0758
(05±1010)Shift Solenoid ºBº Electrical
(Shift Solenoid Valve S2) Open or short in shift solenoid valve S2 circuit
 Shift solenoid valve S2
 ECM


P0770
(05±1013)Shift Solenoid ºEº Malfunction
(Shift Solenoid Valve SL)
 Shift solenoid valve SL is stuck open or closed
 Valve body blocked or stuck
 Shift solenoid valve SL
 Torque converter clutch
 Automatic transaxle (clutch, brake or gear etc.)


P0773
(05±1015)Shift Solenoid ºEº Electrical
(Shift Solenoid Valve SL) Open or short in shift solenoid valve SL circuit
 Shift solenoid valve SL
 ECM


P1520
(05±1018)Stop Light Switch Circuit
 Open or short in stop light switch circuit
 Stop lamp switch assy
 ECM


P1725
(05±1019)NT Revolution Sensor Circuit
Malfunction
(Input Turbine Speed Sensor) Open or short in speed sensor (NT) circuit
 Speed sensor (NT)
 ECM


P1760
(05±1021)Linear Solenoid for Line Pres-
sure Control Circuit Malfunction
(Shift Solenoid Valve SLT) Open or short in shift solenoid valve SLT circuit
 Shift solenoid valve SLT
 ECM


P1780
(05±1024)Park/Neutral Position Switch
Malfunction Short in park/neutral position switch circuit
 Park/Neutral position switch assy
 ECM


P1790
(05±1027)ST Solenoid Circuit Malfunction
(Shift Solenoid Valve ST) Open or short in shift solenoid valve ST circuit
 Shift solenoid valve ST
 ECM


P1798
(05±1030)SB Solenoid Circuit Malfunction
(Shift Solenoid Valve SB) Open or short in shift solenoid valve SB circuit
 Shift solenoid valve SB
 ECM



± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U341E)05±997
AVENSIS REPAIR MANUAL (RM1018E)
HINT:
This DTC may be output when the clutch, brake and gear components, etc. inside the automatic transmis-
sion are damaged.

D25466
12
12
(+)
(±)
± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))05±963
AVENSIS REPAIR MANUAL (RM1018E)
DTC P0776 PRESSURE CONTROL SOLENOID ºBº
PERFORMANCE (SHIFT SOLENOID VALVE
SL2)
SYSTEM DESCRIPTION
The ECM uses signals from the vehicle speed sensor to detect the actual gear position (1st, 2nd, 3rd or O/D
gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
troubles of the shift solenoid valves and valve body.
DTC No.DTC Detecting ConditionTrouble Area
P0776The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Shift solenoid valve SL2 is stuck open or closed

Valve body is blocked up or stuck

Automatic transaxle (clutch, brake or gear etc.)
INSPECTION PROCEDURE
1 INSPECT SHIFT SOLENOID VALVE(SL2)
(a) Remove the shift solenoid valve SL2.
(b) Measure the resistance between terminals.
OK:
Resistance: 5.1 to 5.5
at 20C (68F)
(c) Connect the positive (+) lead with a 21 W bulb to terminal
2 and the negative (±) lead to terminal 1 of the solenoid
valve connector, then check the movement of the sole-
noid valve.
OK:
The solenoid valve makes an operating noise.
NG REPLACE SHIFT SOLENOID VALVE(SL2)
OK
2 INSPECT TRANSMISSION VALVE BODY ASSY
NG REPAIR OR REPLACE TRANSMISSION VALVE
BODY ASSY
OK
05C9G±01

D25467
(+)(±)
05±962± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))
AVENSIS REPAIR MANUAL (RM1018E)
DTC P0766 SHIFT SOLENOID ºDº PERFORMANCE
(SHIFT SOLENOID VALVE S4)
SYSTEM DESCRIPTION
The ECM uses signals from the vehicle speed sensor to detect the actual gear position (1st, 2nd, 3rd or O/D
gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
troubles of the shift solenoid valves and valve body.
DTC No.DTC Detecting ConditionTrouble Area
P0766The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)
Shift solenoid valve S4 is stuck open or closed

Valve body is blocked up or stuck

Automatic transaxle (clutch, brake or gear etc.)
INSPECTION PROCEDURE
1 INSPECT SHIFT SOLENOID VALVE(S4)
(a) Remove the shift solenoid valve S4.
(b) Measure the resistance between the solenoid connector
and the solenoid body.
OK:
Resistance: 11 to 15
at 20C (68F)
(c) Connect the positive (+) lead to the terminal of solenoid
connector and the negative (±) lead to the solenoid body.
OK:
The solenoid makes an operating noise.
NG REPLACE SHIFT SOLENOID VALVE(S4)
OK
2 INSPECT TRANSMISSION VALVE BODY ASSY
NG REPAIR OR REPLACE TRANSMISSION VALVE
BODY ASSY
OK
3 INSPECT TORQUE CONVERTER CLUTCH ASSY
NG REPLACE TORQUE CONVERTER CLUTCH
ASSY
OK
REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSY
05C9F±01