Page 5043 of 5135
![TOYOTA AVENSIS 2005 Service Repair Manual E65594
Free Pushed in2
3
41
05–262– DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U341E) (From February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
INSPECTION PROCEDURE
HINT:
U TOYOTA AVENSIS 2005 Service Repair Manual E65594
Free Pushed in2
3
41
05–262– DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U341E) (From February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
INSPECTION PROCEDURE
HINT:
U](/manual-img/14/57441/w960_57441-5042.png)
E65594
Free Pushed in2
3
41
05–262– DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U341E) (From February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
INSPECTION PROCEDURE
HINT:
Using the Intelligent Tester II Data List allows switch, sensor, actuator and other item values to be read with-
out removing any parts. Reading the Data List early in troubleshooting is one way to shorten labor time.
NOTICE:
In the table below, the values listed under ”Normal Condition” are reference values. Do not depend
solely on these reference values when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Intelligent Tester II to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ”Enter / Power train / Engine and ECT / Data List”.
(g) Follow the instructions on the tester and read the Data List.
ItemMeasurement Item/
Range (display)Normal Condition
Stop Light SwitchStop light SW Status/
ON or OFFBrake Pedal is depressed: ON
Brake Pedal is released: OFF
1 INSPECT STOP LAMP SWITCH ASSY
(a) Remove the stop lamp switch assy.
(b) Measure the resistance according to the value(s) in the
table below.
Standard:
Switch positionTester ConnectionSpecified Condition
Switch pin free1 – 2Below 1 Ω
Switch pin pushed in↑10 kΩ or higher
Switch pin free3 – 410 kΩ or higher
Switch pin pushed in↑Below 1 Ω
NG REPLACE STOP LAMP SWITCH ASSY
OK
Page 5044 of 5135
\f
\f
H42587
STP(+)
ECM:
E13E12E10E9
–
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U341E) (From February, 2004)05–263
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
2 CHECK HARNESS AND CONNECTOR(STOP LAMP SWITCH ASSY – ECM)
(a) Install the stop lamp switch assy.
(b) Measure the voltage according to the value(s) in the table
below when the brake pedal is depressed and released.
Standard:
ConditionTester ConnectionSpecified Condition
Brake pedal is depressedE10 – 19 (STP) –
Body ground10 to 14 V
Brake pedal is released↑Below 1 V
NG REPAIR OR REPLACE HARNESS OR CONNEC TOR ( SEE PAGE 01–32 )
OK
REPLACE ECM
Page 5089 of 5135
05KYD–01
I33809
E13 E12 E11E10E9
– DIAGNOSTICSCRUISE CONTROL SYSTEM (2AZ–FSE)(From
February, 2004)05–315
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorTerminal DescriptionConditionSpecified Condition
TC (E9–20) – E1 (E11–1)W–L – BRDTC input signalIgnition switch ON → Connect ter-
minals TC and CG of DLC310 to 14 V →
Below 2 V
ST1– (E10–12) – E1 (E11–1)G–W – BRCruise cancel input
signalIgnition switch ON, depress brake
pedal → release brake pedalBelow 1 V →
10 to 14 V
STP (E10–19) – E1 (E11–1)G–W – BRStop lamp switch
input signalIgnition switch ON, depress brake
pedal → release brake pedal10 to 14 V →
Below 1 V
CCS (E10–24) – E1 (E11–1)W – BRCruise control main
switch input signal
Ignition switch ON
Cancel switch held ON
SET/COAST switch held ON
RES/ACC switch held ON
MAIN switch held ON10 to 14 V
6.6 to 10.1 V
4.5 to 7.1 V
2.3 to 4 V
Below 1 V