Page 97 of 223
Downloaded from www.Manualslib.com manuals search engine 91
INJECTION
PROHIBITED OPERATIONS: SIEMENS HDI DIRECT INJECTION SYSTEM
Engine: DT17BTED4
B1HP23JCB1HP23HC
Diesel injectors.
WARNING: Diesel and ultrasonic cleaners are prohibited.Do not separate the diesel injector carrier (2)from the following components:
- Diesel injector (g)(no replacement parts).
- The fuel flow actuator (e)(destruction).
Do not move the nut (f)(will cause a malfunction).
Do not separate the union (h)from a diesel injector.
It is forbidden
to clean the carbon deposits from the diesel injector nozzle.
Central fuel high pressure common injection rail.
Do not separate the fuel high pressure sensor (j)from the central fuel high pressure injection rail (3).
Angl-C6-page83-100-2005 4/02/05 17:22 Page 91
Page 98 of 223

Downloaded from www.Manualslib.com manuals search engine 92
INJECTION
SAFETY REQUIREMENTS: HDi DIRECT INJECTION SYSTEM
Safety requirements.
Preamble.
All interventions on the injection system must be carried out to conform
with the following requirements and regulations:
- Competent health authorities.
- Accident prevention.
- Environmental protection.
WARNING: Repairs must be carried out by specialised personnel
informed of the safety requirements and of the precautions to be
taken.
Safety requirements.
IMPERATIVE: Take into account the very high pressures in the high
pressure fuel circuit (1600 bars), and respect the requirements
below:
- No smoking in proximity to the high pressure circuit when work is being
carried out.
- Avoid working close to flame or sparks.
Engine running:
- Do not work on the high pressure fuel circuit.
- Always stay clear of the trajectory of any possible jet of fuel, which could
cause serious injuries.
- Do not place your hand close to any leak in the high pressure fuel circuit.After the engine has stopped, wait 30 secondsbefore any intervention.
NOTE:This waiting time is necessary in order to allow the high pressure
fuel circuit to return to atmospheric pressure.
Cleanliness requirements.
Preliminary operations.
IMPERATIVE: The technician should wear clean overall.
Before working on the injection system, it may be necessary to
clean the apertures of the following sensitive componen (refer to
corresponding procedures):
- Fuel filter.
- Fuel high pressure pump.
- Fuel high pressure common injection rail.
- Fuel high pressure pipes
- Diesel injector carriers.
IMPERATIVE: After dismantling, immediately block the apertures of
sensitive components with plugs, to avoid the entry of impurities.
Work area:
- The work area must be clean and free of clutter.
- Components being worked on must be protected from dust.
Angl-C6-page83-100-2005 4/02/05 17:22 Page 92
Page 99 of 223
Downloaded from www.Manualslib.com manuals search engine 93
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Engine: DT17BTED4
Tools.
[1] Ø 10 mmlow pressure connector: 4215-T
[2] Ø 8 mmlow pressure connector: 4218-T
[3]Pressure gauge for testing boost pressure: 4073-T Kit 4073-T
[4]Extension: 4251-T
Checks.
IMPERATIVE : Respect the safety and cleanliness requirements specific to high pressure
diesel injection (HDi) engines.
Connect the tool [1]between the booster pump and the fuel filter (white mark on the fuel supply
pipe).
Connect the tool [2]downstream of the diesel injectors, between the high pressure fuel pump and
the fuel filter green mark on the fuel return pipe.
Connect the tool [3]on tool [1]or on tool [2].
WARNING: Any check of pressure downstream of the fuel filter is prohibited.
NOTE:To check the pressures while the vehicle is being driven, insert the extension [4] between
tool [3]and tools [1]or [2].
B1BP3CRD
Angl-C6-page83-100-2005 4/02/05 17:22 Page 93
Page 100 of 223
Downloaded from www.Manualslib.com manuals search engine 94
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Engine: DT17BTED4
Checks on pressure: static.
Switch on the ignition.
For 3 seconds(normal functioning):
- Fuel supply pressure shown by the pressure gauge[3] = 1.1 ± 0.4 bar.
- Fuel return pressure shown by the pressure gauge [3] = 2 ± 0.5 bar.
Abnormal functioning:
Fuel supply Fuel return
Checks
pressure pressure
Between 2and 3 bar 0.8 ± 0.4 barCheck the condition of the diesel fuel filter
More than 3 barMore than 0.8 barCheck the fuel return circuit (pipe pinched)
Between
Less than 0.8 barCheck the fuel suppy circuit :
0.3and 0.5 barBooster pump (low pressure), piping
Impossible to start the engine:
- Fuel supply pressure less than 0.3 bar.
B1BP3CRD
Angl-C6-page83-100-2005 4/02/05 17:22 Page 94
Page 101 of 223
Downloaded from www.Manualslib.com manuals search engine 95
INJECTION
CHECKS: TURBO PRESSURE
Engine: DT17BTED4
Tools.
[1]Pressure gauge for checking the pressure: 7073-T.A
[2]Tool for checking the inlet air pressure/vacuum: (-).0171.G3
[3] LEXIAdiagnostic tool: 4171-T
[4] PROXIAdiagnostic tool: 4165-T
Checks.
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Preliminary operations.
WARNING: Prior to any intervention, check the connections of the turbocharger pressure
regulation actuators.
NOTE:If an air flow fault is memorised by the diagnostic tool, refer to the chapter "Air flow from
the turbochargers".
Turbo pressure sensor.
Remove the engine cover.
Disconnect the connector "a".
Remove the turbo pressure sensor (1).
B1BP3CZC
Angl-C6-page83-100-2005 4/02/05 17:22 Page 95
Page 102 of 223
![CITROEN C6 2005 Owners Manual Downloaded from www.Manualslib.com manuals search engine 96
INJECTION
CHECKS: TURBO PRESSURE
Engine: DT17BTED4
Connect:
- The tool [2a]in place of the turbo pressure sensor (1).
- The turbo pressure s CITROEN C6 2005 Owners Manual Downloaded from www.Manualslib.com manuals search engine 96
INJECTION
CHECKS: TURBO PRESSURE
Engine: DT17BTED4
Connect:
- The tool [2a]in place of the turbo pressure sensor (1).
- The turbo pressure s](/manual-img/9/57744/w960_57744-101.png)
Downloaded from www.Manualslib.com manuals search engine 96
INJECTION
CHECKS: TURBO PRESSURE
Engine: DT17BTED4
Connect:
- The tool [2a]in place of the turbo pressure sensor (1).
- The turbo pressure sensor (1)on the tool [2b].
- Tool [1]on tool [2], at "b".
Connect the diagnostic tool [3]or [4]to the vehicle's diagnostic socket:
- Put the diagnostic tool [3]or [4]in parameter measures.
Start the engine.
Accelerate to 2500 rpm.
Compare the pressure values read on the diagnostic tool and on the pressure gauge [1].
NOTE:If there is a significant difference in pressure, replace the turbo pressure sensor.
Air/air exhanger.
Check the condition of the following components:
- Air inlet pipe.
- Airoutlet pipe.
- Air /air exchanger.
Air flow from the turbochargers.
NOTE: If an air flow fault is memorised by the diagnostic tool, check the air flow from the turbocharger
incriminated.
Connect the diagnostic tool [3]or [4]to the vehicle's diagnostic socket:
- Put the diagnostic tool [3]or [4]in parameter measures.
Start the engine.
Accelerate to 2500 rpm.
Compare the air flows (mg/stroke)from the two turbochargers.
B1BP3D0C
Angl-C6-page83-100-2005 4/02/05 17:22 Page 96
Page 103 of 223
Downloaded from www.Manualslib.com manuals search engine 97
INJECTION
CHECKS: TURBO PRESSURE
Engine: DT17BTED4
Significant difference in pressure between the two turbochargers:
- Stop the engine.
- Remove the air filter with the two flowmeters.
- Mark the flowmeters "d"and "c".
- Remove both flowmeters.
Refit:
- Flowmeter "d"in place of flowmeter "c".
- Flowmeter "c"in place of flowmeter "d".
Start the engine.
Accelerate to 2500 rpm.
Compare the air flows (mg/stroke)from the two turbochargers:
- If the difference in air flow has changed turbochargers, replace the flowmeter that is faulty.
- If the difference in air flow is coming from the same turbocharger, check the condition of the air inlet
and outlet pipes of this turbocharger: replace or repair the parts that are faulty.
- If no anomaly is detected on the air inlet and outlet pipes of the turbocharger: replace the turbocharger.
B1HP24TC
Angl-C6-page83-100-2005 4/02/05 17:22 Page 97
Page 104 of 223
Downloaded from www.Manualslib.com manuals search engine 98
INJECTION
CHECKING THE AIR SUPPLY CIRCUIT SPECIFICATIONS
Engine: DT17BTED4
(1) Air filter: MECAPLAST
(2)Air/air heat exchanger: BEHR
(3) Front turbocharger: GARETT
(4)Air butterfly housing: MAN HUMEL
(5)Rear turbocharger: GARETT
(6)Flowmeters: SIEMENS VDO
B1HP26UD
Angl-C6-page83-100-2005 4/02/05 17:22 Page 98