2005 CITROEN C6 oil filter

Downloaded from www.Manualslib.com manuals search engine AXLES - SUSPENSION - STEERING
Wheels and tyres121 - 124
Checking and adjusting the vehicle height125 - 128
Values for checking and adjusting
the axle geometries129 - 133
Front axle134 - 135
Front axle tightening torques136 - 139
Rear axle140 - 141
Rear axle tightening torques142 - 143
Active suspension with variable damping144 - 149
Suspension tightening torques150 - 154
Draining-filling-bleeding
the hydraulic steering/suspension circuit155 - 158
Power steering specifications159 - 162
Power steering tightening torques163 - 164
Checking the steering assistance
pressure (ES9A engine)165 - 168
Bleeding the hydraulic steering
assistance circuit169AIR CONDITIONING
Quantities: aircon system R134.a 203
Special features: air conditioning circuit 204 - 205
Pollen filter206
Checking the compressor oil level207 - 208
Checking the efficiency of
the air conditioning circuit209 - 215
Air conditioning circuit: ES9A216
Air conditioning circuit: DT17217
CONTENTS
BRAKES
Brake specifications170
Braking system: general specifications171 - 173
Braking system: tightening torques174 - 177
Values for checking and adjusting
the braking system178
General feataures of
the electric parking brake179 - 189
Brake fluid checks190
Drain-fill-bleed the braking system191 - 194
HYDRAULICS
Safety requirements:
active suspension with variable damping195 - 197
Suspension spheres: general specifications 198
Suspension spheres:
specification - identification199 - 200
Depressurising the hydraulic
suspension circuit201 - 202
Angl-C6-Index-2005 4/02/05 17:10 Page IV

Downloaded from www.Manualslib.com manuals search engine Draining methods
Oil capacities are defined according to the following methods
16
GENERAL
CAPACITIES (in litres)
Draining of the engine lubrication system by GRAVITY
Place the vehicle on horizontal ground (in the high position if
hydropneumatic suspension).
The engine should be hot (oil temperature 80°C).
Drain the sump by gravity.
Remove the oil filter cartridge (time for draining and drip-drip = 15
minutesapprox.).
Refit the cap with a new seal.
Refit a new oil filter cartridge.
Refill the engine with oil (see table for oil capacity).
Start the engine to fill the oil filter cartridge.
Stop the engine (allow to stabilise for 5 minutes).Draining of the engine lubrication system by SUCTION
Place the vehicle on horizontal ground (in the high position if
hydropneumatic suspension).
The engine should be hot (oil temperature 80°C).
Remove the oil by suction through the dipstick tube.
Remove the oil filter cartridge.
Maintain the suction of oil in the sump (15 minutesapprox.).
Refit a new oil filter cartridge.
Refill the engine with oil (see table for oil capacity).
Start the engine to fill the oil filter cartridge.
Stop the engine (allow to stabilise for 5 minutes).
WARNING: Remove the suction container before starting the engine.
ESSENTIAL: Systematically check the oil level using the oil dipstick.
Angl-C6-page001-21-2005 4/02/05 17:12 Page 16

Downloaded from www.Manualslib.com manuals search engine 17
CAPACITIES (in litres)
GENERAL
Petrol Diesel
3.0i 24S 2.7 24V
BVA BVA
XFV UHZ
5,25
5,75
5,55
5,95
2
7
4
3
6,3
11,3 13,2
65
Engine type
Engine with filter cartridge
Max. after draining and change of filter (by suction)Max. after draining and change of filter (by gravity)Dry sump
Between min. and max.
Dry automatic gearbox
Volume of oil remaining after draining
Quantity of oil to be put back in after draining
Hydraulic circuit
Cooling circuit
Fuel tank
Angl-C6-page001-21-2005 4/02/05 17:12 Page 17

Downloaded from www.Manualslib.com manuals search engine 18
GENERAL
LUBRICANTS - TOTAL recommended oils
Engine oil specifications
Commercial descriptionTOTAL ACTIVA or TOTAL ACTIVA QUARTZ
Synthetic 9000 Semi-synthetic 7000
S.A.E. norms 0W40 5W30 5W40 10W40 15W40
Climate
ClimateCold Temperate
Hot
Temperate Hot
Petrol enginesACE: A3 ACE: A5 ACE : A3
API: SJ API: SL
Diesel engines (*) (**)ACEA: B5 ACEA: B3 or B4 ACEA: B3
Prohibited API: CF
Prohibited FAP
(*)In the winter season, on HDi engines, it is recommended to use 5W40 oil instead of 10W40oil, this to enhance starting from cold.
(**)Do not use 5W30oil on HDi engines with particle filter (FAP).
Angl-C6-page001-21-2005 4/02/05 17:12 Page 18

Downloaded from www.Manualslib.com manuals search engine 37
ENGINE
ENGINE TIGHTENING TORQUES
Lubrication
19 Oil filter cover 2,3 ± 0,3
20 Oil filter support
0,9 ± 0,221 Oil/coolant heat exchanger22 Oil pressure switch 1,3 ± 0,223 Oil pump assembly 0,9 ± 0,224 Oil gauge 2,3 ± 0,325 Oil level sensor 2,7 ± 0,526 Oil sump 0,9 ± 0,227 Drain plug 2,3 ± 0,328 Oil suction strainer 0,9 ± 0,129 Piston skirt spray jets 1 ± 0,130 Turbocharger lubrication pipe 0,9 ± 0,231 Turbocharger lubrication pipe 1,3 ± 0,3Engine: DT17BTED4
B1DP1M6P
Angl-C6-page022-82-2005 4/02/05 17:19 Page 37

Downloaded from www.Manualslib.com manuals search engine 114
CLUTCH
GEARBOX
TRANSMISSION
DRAINING, FILLING AND TOPPING UP THE AM6 AUTOMATIC GEARBOX
Tool.
[1] Filling cylinder: (-).0340
Respect the safety and cleanliness requirements.
Draining.
IMPERATIVE: Draining of the gearbox must be done with the oil hot (60°C minimum), in order to
ensure that the impurities in suspension in the oil are eliminated.
NOTE:Drainage is only partial, as the torque converter cannot be drained totally.
Raise the vehicle.
Remove:
- The oil level plug (2)by means of the Torx spanner.
- The drain plug (1)using a hexagonalspanner.
NOTE :Around 3 litresof oil should flow out.
Filling.
Fit the drain plug (1)(with a new seal).
Tighten the plug (1)to: 5 ± 1 mdaN.
Remove:
- The air filter housing.
- The oil filler plug (3).
Use tool [1].
B2CP3WZCB1BP317C
Angl-C6-page101-120-2005 4/02/05 17:25 Page 114

Downloaded from www.Manualslib.com manuals search engine 117
CLUTCH
GEARBOX
TRANSMISSION
CHECKING THE OIL PRESSURE IN THE AM6 AUTOMATIC GEARBOX
Tools.
[1]Flexible pipe and pressure gauge: 4601- TF1 Toolkit 4601-T
[2]Flexible union: (-).0336.X Toolkit 8010-T
IMPERATIVE: Respect the safety and cleanliness requirements.
Preliminary operations.
Remove the air filter housing.
Move aside the pipe (1).
Remove the screw (2).
Screw in the tool [2]in place of the screw (2).
B2CP45GCB2CP45FC
Angl-C6-page101-120-2005 4/02/05 17:25 Page 117

Downloaded from www.Manualslib.com manuals search engine 119
CLUTCH
GEARBOX
TRANSMISSION
CHECKING THE OIL PRESSURE IN THE AM6 AUTOMATIC GEARBOX
Checking the torque converter.
WARNING: This check has to be of short duration (2 seconds), as it causes a rapid
rise in the temperature of the oil in the automatic gearbox.
Respect the following checking conditions:
- Engine at operating temperature.
- Gear lever in position D.
- Press on the brake pedal.
- Accelerate the engine to the maximum engine speed (see below).
Gear lever position.: D.
Maximum engine speed for ES9A : 2400 ± 50 rpm.
Maximum engine speed for DT17 : 2600 ± 50 rpm.
Diagnosis:
- If the maximum engine speed obtained is lower than the value indicated, the torque
converter is the cause.
- If the maximum engine speed obtained is higher than the value indicated, the automatic
gearbox is the cause (slipping).
Additional operations.
Remove tools [1]and [2].
Refit the screw (2), with a new seal.
Reposition the pipe (1).
Refit the air filter housing.
B1BP3END
Angl-C6-page101-120-2005 4/02/05 17:25 Page 119