2004 SUBARU FORESTER light

4AT(H4SO)-57
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
2 CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
Measure the resistance of harness between
TCM connector and chassis ground.
Connector & terminal
(B54) No. 22 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 3.Repair the short
circuit in harness
between TCM and
transmission con-
nector.
3 CHECK SHIFT SOLENOID 1.
Measure the resistance between transmission
connector terminals.
Connector & terminal
(T4) No. 1 — No. 16:Is the resistance 10 — 16 Ω? Go to step 4.Go to step 7.
4 CHECK OUTPUT SIGNAL EMITTED FROM
TCM.
1) Connect the connectors to TCM and trans-
mission.
2) Turn the ignition switch to ON (engine
OFF).
3) Move the select lever to “D” range.
4) Measure the voltage between TCM con-
nector and chassis ground.
Connector & terminal
(B54) No. 22 (+) — Chassis ground (
−):Is the voltage more than 9 V? Go to step 5.Go to step 6.
5 CHECK OUTPUT SIGNAL EMITTED FROM
TCM.
1) Turn the HOLD mode switch to ON.
2) Measure the voltage between TCM con-
nector and chassis ground.
Connector & terminal
(B54) No. 22 (+) — Chassis ground (
−):Is the voltage less than 1 V? Even if the
POWER indicator
light was blinking,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
the harness or
contact in TCM.Go to step 6.
6 CHECK POOR CONTACT.Is there poor contact in shift
solenoid 1 circuit?Repair poor con-
tact.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
7 CHECK SHIFT SOLENOID 1 (IN TRANSMIS-
SION).
1) Remove the transmission connector from
bracket.
2) Lift-up or raise the vehicle and support with
rigid rack.
NOTE:
Raise all wheels off ground.
3) Drain the ATF.
CAUTION:
Do not drain the ATF until it cools down.
4) Remove the oil pan, and disconnect con-
nector from shift solenoid 1.
5) Measure the resistance between shift sole-
noid 1 connector and transmission ground.
Te r m i n a l s
No. 1 — Transmission ground:Is the resistance 10 — 16 Ω? Go to step 8.Replace the shift
solenoid 1. to 4AT-71, Shift
Solenoids, Duty
Solenoids and ATF
Temperature Sen-
sor.> Step Check Yes No

4AT(H4SO)-58
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
8 CHECK HARNESS CONNECTOR BETWEEN
SHIFT SOLENOID 1 AND TRANSMISSION.
Measure the resistance of harness between
shift solenoid 1 and transmission connector.
Connector & terminal
(T4) No. 1 — (AT5) No. 1:Is the resistance less than 1
Ω?Go to step 9.Repair the open
circuit in harness
between shift sole-
noid 1 and trans-
mission connector.
9 CHECK HARNESS CONNECTOR BETWEEN
SHIFT SOLENOID 1 AND TRANSMISSION.
Measure the resistance of harness between
shift solenoid 1 connector and transmission
ground.
Connector & terminal
(T4) No. 1 — Transmission ground:Is the resistance more than 1
MΩ?Even if the
POWER indicator
light was blinking,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
the harness or
connector in shift
solenoid 1 and
transmission.Repair the short
circuit harness
between shift sole-
noid 1 and trans-
mission connector. Step Check Yes No

4AT(H4SO)-60
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from TCM and
transmission.
3) Measure the resistance of harness
between TCM and shift solenoid 2 connector.
Connector & terminal
(B54) No. 5 — (B11) No. 2:Is the resistance less than 1
Ω?Go to step 2.Repair the open
circuit in harness
between TCM and
transmission con-
nector.
2 CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
Measure the resistance of harness between
TCM connector and transmission ground.
Connector & terminal
(B54) No. 5 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 3.Repair the short
circuit in harness
between TCM and
transmission con-
nector.
3 CHECK SHIFT SOLENOID 2.
Measure the resistance between transmission
connector terminals.
Connector & terminal
(T4) No. 2 — No. 16:Is the resistance 10 — 16 Ω? Go to step 4.Go to step 6.
4 CHECK OUTPUT SIGNAL EMITTED FROM
TCM.
1) Connect the connectors to TCM and trans-
mission.
2) Lift-up or raise the vehicle and support with
rigid rack.
N
OTE:
Raise all wheels off ground.
3) Start the engine and warm-up the transmis-
sion until ATF temperature is above 80°C
(176°F).
NOTE:
If ambient temperature is below 0°C (32°F),
drive the vehicle until ATF reaches its operating
temperature.
4) Move the selector lever to “D” range, and
slowly increase vehicle speed to 50 km/h (31
MPH).
NOTE:
The speed difference between front and rear
wheels may light the ABS warning light, but this
indicates no malfunction. When AT control diag-
nosis is finished, perform the ABS memory
clearance procedure of on-board diagnostics
system. Mode.>
5) Measure the voltage between TCM con-
nector and chassis ground.
Connector & terminal
(B54) No. 5 (+) — Chassis ground (
−):Is the voltage less than 1 V? Even if the
POWER indicator
light was blinking,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
the harness or
connector in TCM
and transmission.Go to step 5.
5 CHECK POOR CONTACT.Is there poor contact in shift
solenoid 2 circuit?Repair the poor
contact.Replace the TCM.
Transmission Con-
trol Module
(TCM).>

4AT(H4SO)-61
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
6 CHECK SHIFT SOLENOID 2 (IN TRANSMIS-
SION).
1) Remove the transmission connector from
bracket.
2) Drain the ATF.
CAUTION:
Do not drain the ATF until it cools down.
3) Remove the oil pan, and disconnect con-
nector from shift solenoid 2.
4) Measure the resistance between shift sole-
noid 2 connector and transmission ground.
Connector & terminal
No. 1 — Transmission ground:Is the resistance 10 — 16 Ω? Go to step 7.Replace the shift
solenoid 2 assem-
bly. 71, Shift Sole-
noids, Duty Sole-
noids and ATF
Temperature Sen-
sor.>
7 CHECK HARNESS CONNECTOR BETWEEN
SHIFT SOLENOID 2 AND TRANSMISSION.
Measure the resistance of harness between
shift solenoid 2 and transmission connector.
Connector & terminal
(AT6) No. 1 — (T4) No. 2:Is the resistance less than 1
Ω?Go to step 8.Repair the open
circuit in harness
between shift sole-
noid 2 and trans-
mission connector.
8 CHECK HARNESS CONNECTOR BETWEEN
SHIFT SOLENOID 2 AND TRANSMISSION.
Measure the resistance of harness between
shift solenoid 2 connector and transmission
ground.
Connector & terminal
(T4) No. 2 — Transmission ground:Is the resistance more than 1
MΩ?Even if the
POWER indicator
light was blinking,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
the harness or
connector in shift
solenoid 2 and
transmission.Repair the short
circuit harness
between shift sole-
noid 2 and trans-
mission connector. Step Check Yes No

4AT(H4SO)-63
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from TCM and
transmission.
3) Measure the resistance of harness
between TCM and transmission connector.
Connector & terminal
(B54) No. 15 — (B11) No. 3:Is the resistance less than 1
Ω?Go to step 2.Repair the open
circuit in harness
between TCM and
transmission con-
nector.
2 CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
Measure the resistance of harness between
TCM connector and chassis ground.
Connector & terminal
(B54) No. 15 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 3.Repair the short
circuit in harness
between TCM and
transmission con-
nector.
3 CHECK LOW CLUTCH TIMING SOLENOID.
Measure the resistance between transmission
connector terminals.
Connector & terminal
(T4) No. 3 — No. 16:Is the resistance 10 — 16 Ω? Go to step 4.Go to step 7.
4 CHECK OUTPUT SIGNAL EMITTED FROM
TCM.
1) Connect the connectors to TCM and trans-
mission.
2) Turn the ignition switch to ON (engine
OFF).
3) Move the select lever to “D” range.
4) Measure the voltage between TCM con-
nector and chassis ground.
Connector & terminal
(B54) No. 15 (+) — Chassis ground (
−):Is the voltage more than 9 V? Go to step 5.Go to step 6.
5 CHECK OUTPUT SIGNAL EMITTED FROM
TCM.
1) Turn the HOLD mode switch to ON.
2) Measure the voltage between TCM con-
nector and chassis ground.
Connector & terminal
(B54) No. 15 (+) — Chassis ground (
−):Is the voltage less than 1 V? Even if the
POWER indicator
light was blinking,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
the harness or
contact in TCM
and transmission.Go to step 6.
6 CHECK POOR CONTACT.Is there poor contact in low
clutch timing solenoid circuit?Repair the poor
contact.Replace the TCM.
Transmission Con-
trol Module
(TCM).>

4AT(H4SO)-64
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
7 CHECK LOW CLUTCH TIMING SOLENOID
(IN TRANSMISSION).
1) Remove the transmission connector from
bracket.
2) Lift-up or raise the vehicle and support with
rigid rack.
N
OTE:
Raise all wheels off ground.
3) Drain the ATF.
CAUTION:
Do not drain the ATF until it cools down.
4) Remove the oil pan, and disconnect con-
nector from low clutch timing solenoid.
5) Measure the resistance between low clutch
timing solenoid connector and transmission
ground.
Te r m i n a l s
No. 1 — Transmission ground:Is the resistance 10 — 16 Ω? Go to step 8.Replace the low
clutch timing sole-
noid. 71, Shift Sole-
noids, Duty Sole-
noids and ATF
Temperature Sen-
sor.>
8 CHECK HARNESS CONNECTOR BETWEEN
LOW CLUTCH TIMING SOLENOID AND
TRANSMISSION.
Measure the resistance of harness between
low clutch timing solenoid and transmission
connector.
Connector & terminal
(AT9) No. 1 — (AT4) No. 3:Is the resistance less than 1
Ω?Go to step 9.Repair the open
circuit in harness
between low clutch
timing solenoid
and transmission
connector.
9 CHECK HARNESS CONNECTOR BETWEEN
LOW CLUTCH TIMING SOLENOID AND
TRANSMISSION.
Measure the resistance of harness between
low clutch timing solenoid connector and trans-
mission ground.
Connector & terminal
(T4) No. 3 — Transmission ground:Is the resistance more than 1
MΩ?Even if the
POWER indicator
light was blinking,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
the harness or
connector in low
clutch timing sole-
noid and transmis-
sion.Repair the short
circuit harness
between low clutch
timing solenoid
and transmission
connector. Step Check Yes No

4AT(H4SO)-66
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
2 CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
Measure the resistance of harness between
TCM connector and chassis ground.
Connector & terminal
(B54) No. 16 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 3.Repair the short
circuit in harness
between TCM and
transmission con-
nector.
3 CHECK 2-4 BRAKE TIMING SOLENOID.
Measure the resistance between transmission
connector terminals.
Connector & terminal
(T4) No. 4 — No. 16:Is the resistance 10 — 16 Ω? Go to step 4.Go to step 7.
4 CHECK OUTPUT SIGNAL EMITTED FROM
TCM.
1) Connect the connectors to TCM and trans-
mission.
2) Lift-up or raise the vehicle and support with
rigid rack.
N
OTE:
Raise all wheels off ground.
3) Start the engine and warm-up the transmis-
sion until ATF temperature is above 80°C
(176°F).
N
OTE:
If ambient temperature is below 0°C (32°F),
drive the vehicle until ATF reaches its operating
temperature.
4) Move the selector lever to “1” range, and
slowly increase vehicle speed to 10 km/h (6
MPH).
N
OTE:
The speed difference between front and rear
wheels may light the ABS warning light, but this
indicates no malfunction. When AT control diag-
nosis is finished, perform the ABS memory
clearance procedure of on-board diagnostics
system. Mode.>
5) Measure the voltage between TCM con-
nector and chassis ground.
Connector & terminal
(B54) No. 16 (+) — Chassis ground (
−):Is the voltage less than 1 V? Go to step 5.Go to step 6.
5 CHECK OUTPUT SIGNAL EMITTED FROM
TCM.
1) Move the selector lever to “D” range, and
slowly increase vehicle speed to 65 km/h (40
MPH).
N
OTE:
The speed difference between front and rear
wheels may light the ABS warning light, but this
indicates no malfunction. When AT control diag-
nosis is finished, perform the ABS memory
clearance procedure of on-board diagnostics
system. Mode.>
2) Measure the voltage between TCM con-
nector and chassis ground.
Connector & terminal
(B54) No. 16 (+) — Chassis ground (
−):Is the voltage more than 9 V? Even if the
POWER indicator
light was blinking,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
the harness or
contact in trans-
mission.Go to step 6. Step Check Yes No

4AT(H4SO)-67
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
6 CHECK POOR CONTACT.Is there poor contact in 2-4
brake timing solenoid circuit?Repair the poor
contact.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
7 CHECK 2-4 BRAKE TIMING SOLENOID (IN
TRANSMISSION).
1) Remove the transmission connector from
bracket.
2) Lift-up or raise the vehicle and support with
rigid rack.
N
OTE:
Raise all wheels off ground.
3) Drain the ATF.
CAUTION:
Do not drain the ATF until it cools down.
4) Remove the oil pan, and disconnect con-
nector from 2-4 brake timing solenoid.
5) Measure the resistance between 2-4 brake
timing solenoid connector and transmission
ground.
Te r m i n a l s
No. 1 — Transmission ground:Is the resistance 10 — 16 Ω? Go to step 8.Replace the 2-4
brake timing sole-
noid. 71, Shift Sole-
noids, Duty Sole-
noids and ATF
Temperature Sen-
sor.>
8 CHECK HARNESS CONNECTOR BETWEEN
2-4 BRAKE TIMING SOLENOID AND
TRANSMISSION.
Measure the resistance of harness between 2-
4 brake timing solenoid and transmission con-
nector.
Connector & terminal
(AT8) No. 1 — (T4) No. 4:Is the resistance less than 1
Ω?Go to step 9.Repair the open
circuit in harness
between 2-4 brake
timing solenoid
and transmission
connector.
9 CHECK HARNESS CONNECTOR BETWEEN
2-4 BRAKE TIMING SOLENOID AND
TRANSMISSION.
Measure the resistance of harness between 2-
4 brake timing solenoid connector and trans-
mission ground.
Connector & terminal
(T4) No. 4 — Transmission ground:Is the resistance more than 1
MΩ?Even if the
POWER indicator
light was blinking,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
the harness or
connector in 2-4
brake timing sole-
noid and transmis-
sion.Repair the short
circuit harness
between 2-4 brake
timing solenoid
and transmission
connector. Step Check Yes No