2004 ISUZU TF SERIES torque

7B1-6 MANUAL TRANSMISSION

Torque : 63 N·m (6.4 kg·m/46 lb·ft)
4. Install center bearing on crossmember.
Torque : 69 N·m (7.0 kg·m/51 lb·ft)
5. Check transmission fluid level.
6. Lower vehicle.

7B1-16 MANUAL TRANSMISSION

6. Install starter(15). (Diesel engine only)
NOTE: Tighten the lower bolt temporarily.
After installing the fuel pipe assembly, tighten the bolt to
the specified torque.
Torque: 76 N




m (7.7 kg




m/56 lb




ft)
7. Install the rear support rubber (14) on the
transmission and tighten the nuts to the specified
torque.
Torque: 52 N




m (5.3 kg




m/38 lb




ft)
8. Install the middle part of transmission crossmember
(12) and bolts.
Tighten the nuts to the specified torque.
Torque: 67 N




m (6.8 kg




m/49 lb




ft)
9. Install engine rear mount nuts (11) fixing on
transmission crossmember (12).
Torque: 52 N




m (5.3 kg




m/38 lb




ft)
Remove the transmission jack from transmission
side.
10. Apply grease to top hole portion of the shift fork.
Install slave cylinder (10) and tighten the bolts to the
specified torque.
Torque: 76 N




m (7.7 kg




m/56 lb




ft)
11. Install the fuel pipe brackets (9) on the transmission.
Install the fuel pipe assembly to the fuel brackets.
Torque: Bolt & Nut 76 N




m (7.7 kg




m/56 lb




ft)
Nut 37 N





m (3.8 kg





m/28 lb





ft)
Diesel engine
220R300012

Legend
(1) Bolt
(2) Nut
(3) Fuel Pipe Assembly




6VE1, C24NE
Scan-1
12. Connect transmission harness connectors and clip.
Connector: neutral switch, car speed sensor, and
backup switch.
13. Tighten exhaust pipe fixing nuts (7) to the specified
torque. (Diesel engine only)
Torque: 67 N




m (6.8 kg




m/49 lb




ft)
150R300003

MANUAL TRANSMISSION 7B1-17

14. Install the exhaust pipe (8). (6VE1)
Torque: 67 N




m (6.8 kg




m/49 lb




ft)
RTW37ASH000101
15. Install rear propeller shaft (6).
Torque: 63 N




m (6.4 kg




m/46 lb




ft)
16. Install center bearing on crossemember.
Torque: 69 N




m (7.0 kg




m/51 lb




ft)
17. Install gear control lever (5).
Torque: 19 N




m (1.9 kg




m/14 lb




ft)
18. Install grommet assembly (4).
Torque: Screw 1.4 N




m (0.14 kg




m/12 lb




in)
Nut 7 N




m (0.7 kg




m/61 lb




in)




RTW47BMH000101

Legend
(1) Grommet Assembly
(2) Floor Panel
(3) Front
19. Install front floor console (3) and rear floor console
(2).
20. Install gear control lever knob (1).
To the female thread portion, adhesive (TB1344 or
LOCTITE 222 or equiv.) of 3 - 4 drops to be applied
and transmission knob tightened.
Torque: 9 N




m (0.9 kg




m/78 lb




in)
After tightening to specified torque, knob
rewrenched until direction of shift pattern due
positioned.
21. Connect battery ground cable.

7B1-20 MANUAL TRANSMISSION

13. Remove the rear cover assembly (3) from the
transmission case (5) and intermediate plate (4).
14. Remove intermediate plate with gear assembly (4)
from transmission case (5).
Reassembly
1. Apply recommended liquid gasket (LOCTITE 17430)
or its equivalent to the transmission case (5),
intermediate plate (4) and rear cover (3) fitting
surfaces.
2. Install the intermediate plate with gear assembly (4)
to the transmission case (5).
Pull out the top gear shaft until the ball bearing snap
ring groove protrudes from the transmission case
front cover fitting face.
Avoid subjecting the main shaft to sudden shock or
stress.
3. Install the rear cover with oil seal (3) on the
intermediate plate with gear (4) by performing the
following steps.


Cover the shaft splines with adhesive tape.
This will prevent damage to the oil seal lip. 4. Install a new gasket and gear control box assembly
(1).
Install the harness clips and brackets and then
tighten four new gear control box bolts to the
specified torque.
Torque: 20 N




m (2.0 kg




m/14 lb




ft)
261R300004
5. Install the O-ring (4) to the speedometer driven gear
bushing (3).
Install the driven gear to the speedometer driven
gear bushing (3).
6. Install the speedometer driven gear assembly (2) to
the transmission rear cover (3).
Install the plate (1) to the transmission rear cover
(3).
Torque: 15 N




m (1.5 kg




m/11 lb




ft)

MANUAL TRANSMISSION 7B1-21

7. Install the speedometer sensor (2).
Torque: 27 N




m (2.8 kg




m/20 lb




ft)
225R300001
8. Install top gear bearing snap ring (10) and counter
front bearing snap ring (8).


Use a pair of snap ring pliers to install the snap
rings to the mainshaft and countershaft.


The snap rings must be fully inserted into the
bearing snap ring groove.
9. Front cover with oil seal (9).
Front Cover Oil Seal Replacement


Remove the oil seal from the front cover.


Apply engine oil to a new oil seal outer
circumference.


Apply recommended grease to the oil seal lip.


Use the oil seal installer 5-8840-0026-0 to install
the oil seal to the front cover.

220R3000020
10. Install a new gasket and front cover (9) to the
transmission case.
NOTE: Take care not to damage the oil seal.
Notes When Tightening the Bolt:


After cleaning the bolt hole, dry it thoroughly with air.


After cleaning the screw face of a removed bolt or
new one, dry it thoroughly. Apply recommended
liquid gasket (LOCTITE 242) or its equivalent before
tightening it.
Tighten six front cover bolts to the specified torque.
Torque: 25 N





m (2.6 kg





m/19 lb





ft)
11. Apply molybdenum disulfide type grease to the
areas as shown in the figure and install shift fork (7).
(Diesel engine, C24NE)
F07L100026

7B1-22 MANUAL TRANSMISSION

12. Install the fulcrum bridge to the transmission case.
(6VE1)
Torque: 38 N





m (3.9 kg





m/28 lb





ft)
RTW37ASH0002

Legend
(1) Fulcrum bridge
13. Apply molybdenum disulfide type grease to the pin
hole inner circumferences and thrust surfaces.
(6VE1)
14. Attach the shift fork to the fulcrum bridge and insert
the pin from below of the fulcrum bridge. (6VE1)
15. Install the washer and snap pin. (6VE1)



RTW47BMH000201
16. Pack the inside recess (A) and coat the back (B) of
the release bearing with molybdenum disulfide type
grease as shown in the figure.
A07RW075
17. Install the release bearing (6) on the front cover,
joining it to the shift frok.

7B1-26 MANUAL TRANSMISSION

Reassembly
1. Install rev-5th shift arm and reverse inhibitor (6) and
rev-5th shift rod (5).

Apply oil to the reverse inhibitor inner surface.

Install the shift rod in the intermediate plate (12).


Hold a round bar against the shift rod end lower
face to protect it against damage.

Install a new spring pin.
Never reinstall the used spring pin.


Install the interlock pin (11) in the intermediate
plate (12).
Do not allow the interlock pin to fall from the
intermediate plate (12).
2. Install 1st-2nd shift arm (10) and 3rd-4th shift arm(9)
to intermediate plate and gear assembly (12).
3. Install 3rd-4th shift rod (8) and 1st-2nd shift rod (7).


Install the interlock pin (11) in the intermediate
plate and gear assembly (12).


Install the 3rd-4th shift rod (8) in the intermediate
plate (12).
Do not allow the interlock pin to fall from the
intermediate plate.


Install the interlock pin (11) and then 1st-2nd
shift rod (7) in the intermediate plate (12).
Do not allow the interlock pin to fall from the
intermediate plate.


Hold a round bar against the shift rod end lower
face to protect it against damage.

Install a new spring pin.
Never reinstall the used spring pin.

230RS007
4. Install spring (4).
5. Put detent balls (3) in the intermediate plate holes.


Apply oil to the detent balls.
6. Install detent springs (2) and detent spring plate and
gasket (1).


Install a new gasket and the detent spring plate.


Tighten the detent spring plate bolts to the
specified torque.
Torque: 25 N




m (2.5 kg




m/18 lb




ft)


220RS030

Legend
(1) Warped

7B1-32 MANUAL TRANSMISSION

2. Install bearing snap ring (29).
3. Apply recommended thread locking agents
(LOCTITE 242) or its equivalent to each of the
bearing plate screw threads.
Install bearing plate and screw (28).
Tighten the screws to the specified torque by using
torx bit wrench 5-8840-0047-0.
Torque: 15 N




m (1.5 kg




m/11 lb




ft)

220RW137
4. Install needle bearing (27), reverse gear (26), and
reverse block ring (25). 5. Assemble rev-5th synchronizer assembly (24) by
performing the following steps.
1. Turn the clutch hub face (1) toward the sleeve
groove (2) (rear side) on the outer
circumference.
2. Check that the inserts (3) fit snugly into the
clutch hub (5) ring insert grooves.
3. Check that the inserts springs (4) are fitted to
the inserts as shown in the illustration.
4. Check that the clutch hub (5) and the sleeve (6)
slide smoothly.
5. Install the synchronizer assembly (24) to the
mainshaft.
The clutch hub face with the heavy boss must be
facing the reverse gear side.

226RS013

226RS049