2004 ISUZU TF SERIES torque

7B1-78 MANUAL TRANSMISSION

Rear Oil Seal Replacement
220R300025

Legend
(1) Installer 5-8840-2797-0
(2) Grip 5-8840-0007-0
1. Remove the oil seal from the rear case and discard
the used oil seal.
2. Apply engine oil to new oil seal outer surfaces.
3. Apply recommended grease (BESCO L2) or
equivalent to the oil seal lip.
4. Use the oil seal installer 5-8840-2797-0 and grip 5-
8840-0007-0 to install the oil seal to the rear case.
Reassembly
1. Apply recommended liquid gasket (LOCTITE 17430)
or its equivalent to the transmission case (4),
intermediate plate (3) and rear case (2) fitting
surfaces.
2. Install the intermediate plate with gear assembly (3)
to the transmission case (4).
Pull out the top gear shaft until the ball bearing snap
ring groove protrudes from the transmission case
front cover fitting face.
Avoid subjecting the mainshaft to sudden shock or
stress.
3. Install the rear case with oil seal (2) on the
intermediate plate with gear (3) by performing the
following steps.


Cover the shaft splines with adhesive tape.
This will prevent damage to the oil seal lip.


Tighten the transmission rear case bolts and
nuts to the specified torque.
Torque: 37 N




m (3.8 kg




m/27 lb




ft)

220R300026

Notes When Tightening the Bolt:


After cleaning the bolt hole, dry it thoroughly with air.

After cleaning the screw face of a removed bolt or
new one, dry it thoroughly. Apply recommended
liquid gasket (LOCTITE 242) or its equivalent on
them before tightening it.
4. Install a new gasket and gear control box assembly
(1).
Install the harness clips and brackets and then
tighten four new gear control box bolts to the
specified torque.
Torque: 20 N




m (2.0 kg




m/14 lb




ft)
261R300004

MANUAL TRANSMISSION 7B1-79

5. Install top gear bearing snap ring (9) and counter
front bearing snap ring (7).


Use a pair of snap ring pliers to install the snap
rings to the mainshaft and countershaft.


The snap rings must be fully inserted into the
bearing snap ring groove.
6. Front cover with oil seal (8).
Front Cover Oil Seal Replacement


Remove the oil seal from the front cover.


Apply engine oil to a new oil seal outer
circumference.

Apply recommended grease to the oil seal lip.


Use the oil seal installer 5-8840-0026-0 to install
the oil seal to the front cover.
220R3000020
8. Apply molybdenum disulfide type grease to the
areas as shown in the figure and install shift fork (6).
(Diesel engine, C24NE)
F07L100026
9. Install the fulcrum bridge to the transmission case.
(6VE1)
Torque: 38 N




m (3.9 kg




m/28 lb




ft)
RTW37ASH0002

Legend
(1) Fulcrum bridge

10. Apply molybdenum disulfide type grease to the pin
hole inner circumferences and thrust surfaces.
(6VE1)
11. Attach the shift fork to the fulcrum bridge and insert
the pin from below of the fulcrum bridge. (6VE1)

7B1-84 MANUAL TRANSMISSION

Reassembly
1. Install rev-5th shift arm and reverse inhibitor (6) and
rev-5th shift rod (5).

Apply oil to the reverse inhibitor inner surface.

Install the shift rod in the intermediate plate (12).


Hold a round bar against the shift rod end lower
face to protect it against damage.

Install a new spring pin.
Never reinstall the used spring pin.


Install the interlock pin (11) in the intermediate
plate (12).
Do not allow the interlock pin to fall from the
intermediate plate (12).
2. Install 1st-2nd shift arm (10) and 3rd-4th shift arm(9)
to intermediate plate and gear assembly (12).
3. Install 3rd-4th shift rod (8) and 1st-2nd shift rod (7).


Install the interlock pin (11) in the intermediate
plate and gear assembly (12).


Install the 3rd-4th shift rod (8) in the intermediate
plate (12).
Do not allow the interlock pin to fall from the
intermediate plate.


Install the interlock pin (11) and then 1st-2nd
shift rod (7) in the intermediate plate (12).
Do not allow the interlock pin to fall from the
intermediate plate.


Hold a round bar against the shift rod end lower
face to protect it against damage.

Install a new spring pin.
Never reinstall the used spring pin.

230RS007
4. Install spring (4).
5. Put detent balls (3) in the intermediate plate holes.


Apply oil to the detent balls.
6. Install detent springs (2) and detent spring plate and
gasket (1).


Install a new gasket and the detent spring plate.


Tighten the detent spring plate bolts to the
specified torque.
Torque: 25 N




m (2.5 kg




m/18 lb




ft)


220RS030

Legend
(1) Warped

MANUAL TRANSMISSION 7B1-89

2. Install bearing snap ring (26).
3. Apply recommended thread locking agents
(LOCTITE 242) or its equivalent to each of the
bearing plate screw threads.
Install bearing plate and screw (25).
Tighten the screws to the specified torque by using
torx bit wrench 5-8840-0047-0.
Torque: 15 N




m (1.5 kg




m/11 lb




ft)

220RW137
4. Install needle bearing (24), reverse gear (23), and
reverse block ring (22). 5. Assemble rev-5th synchronizer assembly (21) by
performing the following steps.
1. Turn the clutch hub face (1) toward the sleeve
groove (2) (rear side) on the outer
circumference.
2. Check that the inserts (3) fit snugly into the
clutch hub (5) ring insert grooves.
3. Check that the inserts springs (4) are fitted to
the inserts as shown in the illustration.
4. Check that the clutch hub (5) and the sleeve (6)
slide smoothly.
5. Install the synchronizer assembly (21) to the
mainshaft.
The clutch hub face with the heavy boss must be
facing the reverse gear side.

226RS013

226RS049

7B1-90 MANUAL TRANSMISSION

6. Mesh the 1st-2nd and 3rd-4th synchronizers with
both the 1st and 3rd gears (double engagement).

226RS015
This will prevent the mainshaft from turning.
7. Install the new mainshaft hub nut.
Use the mainshaft nut wrench 5-8840-2156-0 to
tighten the mainshaft nut (20) to the specified
torque.
Torque: 137 N




m (14 kg




m/101 lb




ft)
226RW214


8. Use a punch to stake the mainshaft nut (20).

226RW153
9. Install needle bearing (19), 5th block ring (18), and
5th gear (17).
10. Apply engine oil to the counter reverse gear (16) and
the reverse gear (23).
Install the counter reverse gear (16) to the counter
shaft.
The reverse gear projection must be facing the
intermediate plate.

226RW151

7B1-108 MANUAL TRANSMISSION

Torque Specifications

RTW47BLF001101
About arrow mark, refer to Transmission (MUA) Installation in this section.

MANUAL TRANSMISSION 7B1-109

Torque Specifications (Cont'd)

RTW47BLF000801

7B1-110 MANUAL TRANSMISSION

Torque Specifications (Cont'd)

RTW47BLF000601