2004 ISUZU TF SERIES torque

POWER-ASSISTED STEERING SYSTEM 3B-25

Main Data and Specifications
General Specifications
Oil pump Type Vane
Operating fluid
ATF DEXRON®
III



Torque Specifications
C24SE N
m (kg
m/Ib ft)


RTW43BLF000401

3B-26 POWER-ASSISTED STEERING SYSTEM

Power Steering Pump and Associated Parts (6VE1)
RTW33BLF000701

Legend
(1) Pump Assembly
(2) Hose, Suction
(3) Hose, Flexible


(4) Bolt
(5) Connector, Pressure switch

Removal
1. Remove the drive belt.
2. Place a drain pan below the pump.
3. Disconnect the suction hose.
4. Disconnect the flexible hose.
5. Disconnect the oil pressure switch connector.
6. Remove the power steering fixing bolt and remove
the pump assembly.

Installation
1. Install the pump assembly to the pump braket,
tighten the fixing bolt to the specified torque.
Torque: 31-63 N·m (3.2-6.4 kg·m/23-46 lb ft)
2. Connector the oil pressure switch connector.
3. Install the flexible hose.
Tighten the eye bolt to specified torque.
Torque: 49 - 59 N·m (5.0 – 6.0 kg·m/36 - 43 lb ft)
4. Install the drive belt.
5. Connect the suction hose, then fill and bleed
system.
Refer to Bleeding the Power Steering System in this
section.

POWER-ASSISTED STEERING SYSTEM 3B-29

3. Install the vanes to roter with curved face in contact
with the inner wall of cam.
442RS005
4. Install rotor and vanes to cam.
5. Install pin to front housing.
6. Install two new O-rings to front housing. Be sure to
discard used O-ring.
7. Install side plate.
CAUTION: When installing side plate, be careful not
to damage its inner surface. Damaged side plate
may cause poor pump performance, pump seizure
or oil leakage.
8. Install pump cartridge assembly to front housing.
9. Install snap ring to shaft end.
10. Install rear housing with a new O-ring. Be sure to
discard used O-ring. Then install bolt and tighten i
t
to specified torque.
Torque: 22-26 N




m (2.2-2.7 kg




m/16-20 lb ft)
11. Install suction pipe with a new O-ring. Be sure to
discard used O-ring. Then install bolt and tighten i
t
to specified torque.
Torque: 7.8-12 N




m (0.8-1.2 kg




m/6-9 lb ft)
12. Install relief valve and spring.
13. Install connector with a new O-ring. Be sure to
discard used O-ring. Tighten the connector to
specified torque.
Torque: 49-69 N




m (5.0-7.0 kg




m/36-51 lb ft)
14. Install pressure switch assembly and tighten it to
specified torque.
Torque: 15-20 N




m (1.5-2.0 kg




m/11-14 lb ft)

3B-30 POWER-ASSISTED STEERING SYSTEM

Main Data and Specifications
General Specifications
Oil pump Type Vane
Operating fluid
ATF DEXRON®
III



Torque Specifications
6VE1 N
m (kg
m/Ib ft)


RTW43BMF000401

POWER-ASSISTED STEERING SYSTEM 3B-35

Inspection and Repair (with SRS air
bag)
The inflator module consists of a cover, air bag, inflator,
and retainer. Inspect the inflator module mainly for the
following:


Check for holes, cracks, severe blemishes and
deformation on the cover.


Check that the retainer is not deformed.


Check for defects such as damage and breakage in
the lead wire for the igniter.
If an abnormality is found as the result of the inspection,
replace the inflator module with a new one.

Installation
1. Support the inflator module and carefully connect the
SRS connector and horn lead. (with SRS air bag)
060R300041


2. Connect the horn leads at center of wheel. (without
SRS air bag)
NOTE: Horn leads is letting a bracket top pass.
(Plastic type steering wheel only)



RTW43BSH000301
3. Push the born pad area 1-4.
Tighten the born pad fixing screw to the specifed
torque (without SRS air bag)
Torque: 2 - 4 N





m (0.2 – 0.4 kg





m/17 - 35 lb ft)
NOTE: A horn pad is not struck at the time o
f
attachment.



RTW43BSH000401

3B-40 POWER-ASSISTED STEERING SYSTEM



430RX005-X
14. Remove steering column cover.
15. Disconnect the wiring harness connectors located
under the steering column then remove combination
switch and SRS coil assembly.

Installation
1. Align the setting marks made when removing then
install steering wheel.
Refer to the adjustment method in case a mark is
not attached in this section.
NOTE: Confirm SRS and Horn harness connector is
fixed by the steering wheel.
RTW33BSH000601

CAUTION: Never apply force to the steering wheel in
direction of the shaft by using a hammer or othe
r
impact tools in an attempt to remove the steering
wheel. The steering shaft is designed as an energy
absorbing unit.
2. Tighten the steering wheel fixing nut to the specified
torque.
Torque: 31 - 39 N





m (3.2 – 4.0 kg





m/23 - 29 lb ft)
3. Support the inflator module and carefully connect the
SRS connector and horn lead. (with SRS air bag)
060R300041
4. Connect the horn leads at center of wheel. (without
SRS air bag)
NOTE: Horn leads is letting a bracket top pass.
(Plastic type steering wheel only)



RTW43BSH000301

POWER-ASSISTED STEERING SYSTEM 3B-41

5. Push the born pad area 1-4.
Tighten the born pad fixing screw to the specifed
torque (without SRS air bag)
Torque: 2 - 4 N




m (0.2 – 0.4 kg




m/17 - 35 lb ft)
NOTE: A horn pad is not struck at the time o
f
attachment.



RTW43BSH000401
6. Align the each snap stud of driver air bag to the hole
of steering wheel. (with SRS air bag)
060R300030


060R300020
7. Push the SRS air bag area1 and area2. At that time
confirm the audible noise of each stud. (with SRS ai
r
bag)
060R300036
8. Enable the SRS (Refer to "Enabling the SRS" in this
section). (with SRS air bag)
9. Connect the SRS connector. (with SRS air bag)
10. Connect the battery "-" terminal cable. (with SRS ai
r
bag)
11. Turn the ignition switch to "ON" while watching
warning light and check the light should flash 7 times
and then go off. If lamp does not operate correctly,
refer to Restraints section.

POWER-ASSISTED STEERING SYSTEM 3B-47

6. Install the driver knee bolster assembly.
7. Install the steering lower cover and engine hood
opening lever.
8. Install the steering wheel and align the setting
marks.
Refer to the adjustment method in case a mark is
not attached in this section.
NOTE: Confirm SRS and Horn harness connector is
fixed by the steering wheel.
RTW33BSH000601
CAUTION: Never apply force to the steering wheel in
direction of the shaft by using a hammer or othe
r
impact tools in an attempt to remove the steering
wheel. The steering shaft is designed as an energy
absorbing unit.
9. Tighten the steering wheel fixing nut to the specified
torque.
Torque: 31 - 39 N




m (3.2 – 4.0 kg




m/23 - 29 lb ft)
10. Support the inflator module and carefully connec
t
the SRS connector and horn lead. (with SRS air
bag)
060R300010

11. Connect the horn leads at center of wheel. (without
SRS air bag)
NOTE: Horn leads is letting a bracket top pass.
(Plastic type steering wheel only)



RTW43BSH000301
12. Push the born pad area 1-4.
Tighten the born pad fixing screw to the specifed
torque (without SRS air bag)
Torque: 2 - 4 N





m (0.2 – 0.4 kg





m/17 - 35 lb ft)
NOTE: A horn pad is not struck at the time o
f
attachment.



RTW43BSH00040