2003 NISSAN TEANA reverse

EI-32
DOOR OUTSIDE LOWER MOLDING

DOOR OUTSIDE LOWER MOLDINGPFP:82877
Removal and InstallationBIS0011P
FRONT AND REAR DOOR OUTSIDE LOWER MOLDING
Removal
1. Half-open front door and rear door.
2. Remove nuts from back of door panel.
3. Disengage mounting clips from molding rear end to front end using a clip clamp remover.
4. Remove door outside lower molding from body side after disengaging.
5. Slide molding toward rear of vehicle, and then remove front end clip.
CAUTION:
After removal, visually inspect molding, and if it is deformed, replace it with new molding.
Installation
Install in the reverse order of removal.
CAUTION:
When installing, confirm clips are accurately aligned with the holes on body side panel, then press in.
PIIA6257E
1. Clip (C101) 2. Door lower molding (front) 3. Stud bolt
4. Door lower molding (rear) 5. Nut

EI-34
TRUNK LID FINISHER

4. Remove trunk lid finisher upper mounting clips, and then pull out
trunk lid finisher upper toward rear of vehicle.
5. Disconnect request switch harness connector (only for models with intelligent key) after pulling out, then
remove trunk lid finisher upper.
6. Continuously, remove trunk lid finisher lower mounting clips the same as in step 4, and then remove trunk
lid finisher lower.
CAUTION:
After removal, visually inspect finisher, and if it is deformed, replace it with new molding.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Replace double-faced adhesive tape on back of finisher with a new tape if trunk lid finisher (lower)
is reused.

Remove double-faced adhesive tape remaining on body and back of finisher using double-faced
adhesive tape remover (SUMITOMO 3M Cleaner 30 or equivalent) when removing finisher (lower).

Install after cleaning adhesive parts of body side and back of finisher (lower).

Do not wash the vehicle within 24 hours after installing so as to keep adhesive.
PIIA7081E

DOOR FINISHER
EI-37
C
D
E
F
G
H
J
K
L
MA
B
EI

12. Remove door trim.
13. Remove the following parts after removing door trim.

Inside handle assembly

Trunk lid opener switch

Step lamp (front only)

Door grip

Front door inside handle

Door grip upper bracket

Seat memory switch (With automatic drive positioner)
Installation
Install in the reverse order of removal.
CAUTION:
When installing door trim, make sure that clips are securely fitted in panel holes on body, and then
press them in.

BODY SIDE TRIM
EI-39
C
D
E
F
G
H
J
K
L
MA
B
EI

FRONT PILLAR GARNISH
Removal
Remove pillar garnish mounting clips using a clip clamp remover,
and then remove pillar garnish.
Installation
Install in the reverse order of removal.
FRONT KICKING PLATE OUTER
Removal
Remove front kicking plate outer mounting clips using a clip clamp
remover, and then remove kicking plate outer.
Installation
Install in the reverse order of removal.
FRONT KICKING PLATE INNER
Removal
Remove kicking plate inner mounting clips using a clip clamp
remover, and then remove kicking plate inner.
Installation
Install in the reverse order of removal.
FRONT BODY SIDE WELT
Removal
1. Remove center pillar lower garnish.
2. Remove center kicking plate inner.
3. Remove front body side welt.
Installation
Install in the reverse order of removal.
PIIA7072E
PIIA7070E
PIIA7073E

EI-40
BODY SIDE TRIM

CENTER PILLAR LOWER GARNISH
Removal
Remove center pillar lower garnish mounting clips using a screw-
driver, and then remove center pillar lower garnish.
Installation
Install in the reverse order of removal.
CENTER PILLAR UPPER GARNISH
Removal
1. Remove center pillar lower garnish.
2. Remove front seat belt floor anchor bolt and front seat belt
shoulder anchor bolt. Refer to SB-3, "
SEAT BELTS" .
3. Remove front body side welt and rear body side welt.
4. Remove center pillar upper garnish.
Installation
Install in the reverse order of removal.
REAR KICKING PLATE OUTER
Removal
Remove rear kicking plate outer mounting clips using a clip clamp
remover, and then remove kicking plate outer.
Installation
Install in the reverse order of removal.
REAR KICKING PLATE INNER
Removal
1. Remove rear seat cushion. Refer to SE-112, "REAR SEAT" .
PIIA7077E
PIIA7078E
PIIA7071E

BODY SIDE TRIM
EI-41
C
D
E
F
G
H
J
K
L
MA
B
EI

2. Remove kicking plate inner mounting clips using a clip clamp
remover, and then remove kicking plate inner.
Installation
Install in the reverse order of removal.
REAR BODY SIDE WELT
Removal
1. Remove center pillar lower garnish.
2. Remove rear seat cushion. Refer to SE-112, "
REAR SEAT" .
3. Remove rear kicking plate inner.
4. Remove rear body side welt.
Installation
Install in the reverse order of removal.
REAR SEATBACK FINISHER
Removal
1. Remove rear seat cushion and rear seatback. Refer to SE-112,
"REAR SEAT" .
2. Remove rear seat belt floor anchor bolt. Refer to SB-5,
"Removal and Installation of Rear Seat Belt" .
3. Remove rear kicking plate inner.
4. Remove rear seatback finisher.
Installation
Install in the reverse order of removal.
NOTE:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
REAR PILLAR FINISHER
Removal
1. Remove rear seat cushion and rear seatback. Refer to SE-112,
"REAR SEAT" .
2. Remove rear seat belt floor anchor bolt. Refer to SB-5,
"Removal and Installation of Rear Seat Belt" .
3. Remove rear kicking plate inner.
4. Remove rear seatback finisher.
5. Remove pillar finisher mounting clips using a screwdriver, and
then remove pillar finisher.
PIIA7074E
PIIA7075E
PIIA7076E

EI-42
BODY SIDE TRIM

CAUTION:
Insert a clip clamp remover wrapped with a shop cloth or
clip clamp remover into the part shown by the arrow
(between the clips and the body side panel). Remove clips.
Installation
Install in the reverse order of removal.
CAUTION:
Make sure that clips are securely fitted in panel holes on body when installing, and then press them in.
SIIA0810E

EI-44
REAR PARCEL SHELF FINISHER

REMOVAL
1. Remove rear seatback and rear seat cushion. Refer to SE-112, "REAR SEAT" .
2. Remove rear seat belt floor anchor bolt and rear seat belt shoulder anchor bolt. Refer to SB-5, "
Removal
and Installation of Rear Seat Belt" .
3. Disengage child anchor cover front pawls, and then pull out child
anchor cover (LH/RH center) toward front of vehicle.(Models
with rear window sunshade)
4. Remove rear kicking plate inner, rear seatback finisher, rear pillar finisher. Refer to EI-38, "
BODY SIDE
TRIM" .
5. Disconnect high-mounted stop lamp harness connector from
trunk room side. (Models without rear window sunshade)
6. Disconnect high-mounted stop lamp harness connector from
front side of rear parcel shelf finisher. (Models with rear window
sunshade)
7. Remove rear parcel shelf finisher mounting clip using a clip clamp remover.
8. Remove rear parcel shelf finisher while disengaging dual-lock fastener on back of rear parcel shelf fin-
isher. (Models with rear window sunshade)
9. Remove the following parts after removing rear parcel shelf finisher.

Rear speaker grille (for woofer)

High-mounted stop lamp
INSTALLATION
Install in the reverse order of removal.
7. Screw 8.Rear parcel shelf finisher (with sun-
shade)9. Child anchor cover (LH/RH center)
10. Rear window sunshade 11. Bolt 12. Locating pin
PIIA9530E
PIIA9531E
PIIA9535E